2 layers65 × 56 mm
RDMA
SkullKill/RDMA-PCB
Rpi Dead Man Alarm - PCB and 3D case - Occupancy Monitoring - Raspberry Pi hat
92 partsGPL-3.0
2 layers65 × 56 mm
ACYONP SMD LCSC
SkullKill/ACYONP-PCB1PCB for Access Control Yubikey OTP NFC Pi (ACYONP). For Raspberry Pi. This is a Door Access Control using Electronic Door Strike, with Yubikey OTP via NFC / KeyPad / WebInterface for Authentication.
- Size
- 65 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 81
- Pads
- 280
- Tracks, vias
- 995, 101
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 Jul 2019
- Updated
- 27 Jul 2019
Overview
ACYONP SMD LCSC is an open-source printed circuit board by SkullKill, from the SkullKill/ACYONP-PCB repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 65 × 56 mm with 93 parts on 81 nets, routed with 995 tracks and 101 vias.
It is built around the CAT24C32LI-, ULN2003A and FMMT491TA, with the SOD1F7, DMG2305UX and DMMT5401 among its other parts. Its parts include 33 resistors, 15 diodes, 15 connectors, 8 transistors and 7 capacitors.
Main components
6
CAT24C32LI-
PDIP-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 2mA 3.5us 32Kbit 5ms 5uA Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROM
ULN2003A
SOP-16-40℃~+85℃ 0.93mA 100uA 15pF 20uA 30V 50V Seven channels SOP-16 Darlington Transistor Arrays ROHSUMWDarlington Transistor Arrays
FMMT491TA
SOT-23-55℃~+150℃ 1 NPN 100nA 150MHz 160mV 1A 500mW 60V 7V 80 NPN SOT-23 Bipolar (BJT) ROHSDiodes IncorporatedTransistors (NPN/PNP)
SOD1F7
SOD-123FL-50℃~+150℃ 1 Independent 1.3V@1A 1A 1kV 30A 500ns 5uA@1kV SOD-123FL Fast Recovery / High Efficiency Diodes ROHSMDDFast Recovery / High Efficiency DiodesDMG2305UX
SOT-23-55℃~+150℃ 1 P-Channel 1.7W 190pF 1V 20V 4.1A 52mΩ@4.5V 7.8nC 740pF P-Channel SOT-23 MOSFETs ROHSTECH PUBLICMOSFETs
DMMT5401
SOT-26(SC74R)-55℃~+150℃ 150V 2 PNP 200mA 200mV 300MHz 300mW 50uA 5V 60 PNP SOT-26(SC74R) Bipolar (BJT) ROHSDiodes IncorporatedBipolar (BJT)
README
README.mdACYONP-PCB
PCB for Access Control Yubikey OTP NFC Pi (ACYONP). For Raspberry Pi. This is a Door Access Control using Electronic Door Strike, with Yubikey OTP via NFC / KeyPad / WebInterface for Authentication.
Web interface shows the status of the whole system, along with the ability to enter pin/password/yubikey OTP string for authentication to unlock the door
Uses Inturrupt and Threads to minimise overhead, and to be non blocking as much as possible.
All options are completely customizable through the ini config file
The script ACYONP is design specificly for the Raspberry Pi.
SKaccess by Simon Kong
ACYONP-SMD-01.jpg
NFC Reader is at the top of the Box, inside. putting the yubikey on top of the box will scan the yubikey neo / yubikey 5 nfc.
ACYONP-webinterface-01.jpg
V 1.0 21/05/2019 - Initial Release
PCB Board Used
Ready to use PCB Board
https://www.skstore.com.au/electronics/pcb/ACYONP
PCB Design Files / gerber files
FYI Gerber files are in the release section
https://github.com/SkullKill/ACYONP-PCB/releases
more pictures in the wiki
https://github.com/SkullKill/ACYONP-PCB/wiki
ACYONP-SMD-Front-Red-RT-V1.2.jpg
ACYONP-SMD-Back-Red-V1.2.jpg
Schematics
ACYONP-SMD-schematics-v1.2a.jpg
Code Used
Product Used (not included)
Dupont kit / Jumper Wires
you will need a dupont crimp kit 2.54 / tool and / or jumper wires
e.g
Crimping Tool: 0.1-1.0 mm² Capacity, 16-28 AWG https://www.pololu.com/product/1928
Crimp Connector Housings https://www.pololu.com/category/70/crimp-connector-housings
Female Crimp Pins for 0.1" Housings https://www.pololu.com/product/1930
Male Crimp Pins for 0.1" Housings https://www.pololu.com/product/1931
Wires with Pre-Crimped Terminals https://www.pololu.com/category/71/wires-with-pre-crimped-terminals
Premium Jumper Wires https://www.pololu.com/category/65/premium-jumper-wires
https://www.futurlec.com/ConnHead.shtml
Keypad
Metallic Waterproof 3x4 Keypad https://www.futurlec.com/Keypads.shtml
PN532 NFC controller in UART mode
e.g
https://www.dfrobot.com/product-892.html
https://wiki.dfrobot.com/NFC_Module_for_Arduino__SKU_DFR0231_
Yubico Yubikey
YubiKey 5 NFC
https://www.yubico.com/product/yubikey-5-nfc
other items used, can be any other ones.
H0307 • 145Lx105Wx65Dmm IP65 Sealed ABS Enclosure
https://www.altronics.com.au/p/h0307-ritec-145lx105wx65dmm-ip65-sealed-abs-enclosure/
H0151 • UB1 (157Lx95Wx53Hmm) Grey ABS Jiffy Box
https://www.altronics.com.au/p/h0151-ub1-157lx95wx53hmm-grey-abs-jiffy-box/
P0628 • 2.1mm Female Plastic Chassis Mount DC Power Socket (not necessary)
https://www.altronics.com.au/p/p0628-2.1mm-female-plastic-chassis-mount-dc-power-socket/
H1554 • 5mm LED Mounts Pk 100
https://www.altronics.com.au/p/h1554-5mm-led-mounts-pk-100/
S6109 • 1.5-24V Piezo Chassis Mount Buzzer (status buzzer)
https://www.altronics.com.au/p/s6109-1.5-24v-piezo-chassis-mount-buzzer/
S6100 • 3-15V Mechanical Chassis Mount Buzzer (door buzzer)
https://www.altronics.com.au/p/s6100-3-15v-mechanical-chassis-mount-buzzer/
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 330Ω | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R18, R27, R29, R30, R31, R32, R33 |
| 7 | LED-Green | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3, D4, D11, D12, D13, D14, D15 |
| 5 | 150Ω | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R8, R12, R16, R20 |
| 5 | FMMT491TA | Package_TO_SOT_SMD:SOT-23 | Q2, Q3, Q5, Q7, Q9 |
| 5 | MountingHole | ACYONP-SMD-LCSC:MountingHole_2.75mm_M2.5_NoPad | H1, H2, H4, H5, H6 |
| 4 | 100nF-25V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2, C3, C5, C6 |
| 4 | 2KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R6, R10, R14 |
| 4 | SOD1F7 | Diode_SMD:D_SOD-123 | D1, D2, D9, D10 |
| 3 | 10KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R4, R11, R25 |
| 3 | 22UF-25V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C4, C7 |
| 3 | 4.7KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R21, R23, R24 |
| 3 | 510Ω | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2, R5, R17 |
| 2 | 270Ω | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9, R13 |
| 2 | 3.9KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R22, R28 |
| 2 | DMG2305UX | Package_TO_SOT_SMD:SOT-23 | Q1, Q12 |
| 2 | LED-Yellow | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5, D6 |
| 1 | 1-Wire | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J12 |
| 1 | 1.2KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R7 |
| 1 | 12Vpsu | pi-template:TerminalBlock_bornier-2_P5.08mm | J16 |
| 1 | 1KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R19 |
| 1 | 3.3UH-8.5A | ACYONP-SMD-LCSC:L_6.3x6.3_H3_HandSolder | L1 |
| 1 | 47KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R15 |
| 1 | 57.6KΩ | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R26 |
| 1 | 5V Reg Sw on-off | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | 5V-12V Jumper | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP2 |
| 1 | 5V-3.3V Sw NFC | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | AlarmStatus | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J20 |
| 1 | CAT24C32 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | DMMT5401 | Package_TO_SOT_SMD:SOT-23-6 | Q11 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | KeyPad3X4 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J8 |
| 1 | LED-Blue | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D8 |
| 1 | LED-Red | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7 |
| 1 | LOGO | ACYONP-SMD-LCSC:skaccessLogo3000 | G*** |
| 1 | LOGO | ACYONP-SMD-LCSC:skaccessLogo2000 | G*** |
| 1 | LatchOpen | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J18 |
| 1 | NFC_Module | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J15 |
| 1 | PTC-2A-16V_1812 | Fuse:Fuse_1812_4532Metric_Pad1.30x3.40mm_HandSolder | F1 |
| 1 | PowerStatus | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J21 |
| 1 | PowerToSolenoidStrike | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | ProgrammingJumper | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J22 |
| 1 | Raspberry_Pi_2_3 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | ReedSwitchOpen | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J19 |
| 1 | Screw_Terminal_01x04_Left_Top | pi-template:TerminalBlock_TE_282834-4_1x04_P2.54mm_Horizontal | J23 |
| 1 | Screw_Terminal_01x06_Top_Right | pi-template:TerminalBlock_TE_282834-6_1x06_P2.54mm_Horizontal | J26 |
| 1 | Screw_Terminal_01x08_Bottom_Left | pi-template:TerminalBlock_TE_282834-8_1x08_P2.54mm_Horizontal | J25 |
| 1 | TPS563200 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U1 |
| 1 | ULN2003A | ACYONP-SMD-LCSC:SOIC-16_ti-Package-D | U3 |
Questions
How big is the ACYONP SMD LCSC PCB?
It measures 65 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ACYONP SMD LCSC use?
93 parts, built around the CAT24C32LI-, ULN2003A, FMMT491TA and SOD1F7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ACYONP SMD LCSC KiCad files?
From the SkullKill/ACYONP-PCB repository on GitHub, at the commit this page was made from: the board is ACYONP-SMD-LCSC.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ACYONP SMD LCSC design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers65 × 56 mm
Toy Ikea MicrowaveController
SkullKill/Toy-Ikea-MicrowaveController-PCB
PCB for Microwave Controller for Ikea Kitchen DUKTIG
73 parts1GPL-3.0 - 2 layers65 × 56.5 mm
Sangaboard v0.4
kitspace-test-repos/Sangaboard
The Sangaboard is a motor controller for unipolar stepper motors such as the cheap 28BYJ-48 motors. The custom board (v0.3) can be programmed as an Arduino Leonardo in the Arduino IDE.
96 parts - 4 layers200 × 100 mm
Heteromycin
hasenbanck/heteromycin
A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
373 parts40 - 2 layers65 × 56 mm
- 2 layers65 × 56 mm
- 2 layers65 × 56 mm
- 2 layers182.5 × 65 mm
V1Panel
pilotniq/MJoulnir
Hardware and software for the control system of a full size electric boat.
171 parts2