Skip to the content
2 layers52.8 × 37.8 mmMr Radar Kit, the printed circuit board in 3D

Mr. Radar is a port security evading, discovery device used to detect network switches connected to lone network ports.

Size
52.8 × 37.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
16
Pads
44
Tracks, vias
80, 0
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
7 Nov 2022
Updated
13 Feb 2023

Overview

Mr Radar Kit is an open-source printed circuit board by skinnyrad, from the skinnyrad/Mr-Radar repository on GitHub. It is a 2-layer board of 52.8 × 37.8 mm with 14 parts on 16 nets, routed with 80 tracks and 0 vias.

It is built around the RJ45. Its parts include 9 resistors, 1 IC, 1 connector and 1 switch.

Main components

1

README

README.md

Mr Radar

Mr. Radar is a port security evading, discovery device used to detect network switches connected to lone network ports. In addition, it has the ability to detect if Power over Ethernet (PoE) is present and whether the PoE being provide is Mode A or Mode B in nature. An understanding of the functionality of Mr. Radar can be found here: https://skinnyrd.com/mr-radar-layer-1-recon/

Mr Radar Photo

Mr. Radar has the following indicators that appear on the Trinket M0.

  • Small Green LED: Mr. Radar is ON. LED is located to the left of the µUSB connector.
  • Large Green LED: Mr. Radar has discovered a network device. LED is the Dotstar in the center.
  • Large Orange LED: Mr. Radar has discovered a network device that can only support 10/100 Mbits/s. LED is the Dotstar in the center.
  • Small Rapid Blinking Red LED: Mr. Radar has detected PoE in a Mode A configuration. LED is located to the right of the µUSB connector.
  • Small Slowly Blinking Red LED: Mr. Radar has detected PoE in a Mode B configuration. LED is located to the right of the µUSB connector.

Github File Structure

The hardware folder contains the KiCad project files for Mr. Radar. The MrRadar_firmware folder contains the .ino file for the Arduino IDE. These files will be used to program the Trinket M0 which controls Mr. Radar.

Schematic

If you don't want to bother with KiCad and just want to make the board from scratch or want to use another microcontroller, the schematic below will help. mrradarschematic

Bill of Materials

Tips for construction

  • When loading the code for the Trinket M0, ensure you have setup the Trinket according to the Adafruit tutorial. Use the Arduino IDE setup procedures.
  • The battery pack goes on the bottom of the board. You'll need to solder everything on top first and then clip all the excess wire pieces before affixing the battery pack.

Parts

14
QtyValueFootprintReferences
4100kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2, R8, R9
410kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R4, R5, R7
13.3kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR6
1Battery_CellBattery Holders Clips and Contacts:AAA_Keystone_2479BT1
1LOGOLOGOG***
1RJ45Modular_Connector_Jacks:RJ45_RJSSE-5080J1
1SW_SPSTButton_Switch_THT:SW_DIP_SPSTx01_Slide_9.78x4.72mm_W7.62mm_P2.54mmSW1
1Trinket_M0Adafruit:Trinket M0U1

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 4 layers84 × 82 mmToad, the printed circuit board in 3D

    Toad

    travisgoodspeed/goodfet

    An embedded bus adapter for various microcontrollers and radios.

    241 parts333
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99
  • 2 layers50 × 55.4 mmCasserole, the printed circuit board in 3D

    Casserole

    puddly/casserole

    Control GE appliances

    23 parts94Apache-2.0
  • 2 layers67.9 × 47.8 mmPlatine, the printed circuit board in 3D

    Platine

    nv1t/standing-desk-interceptor

    I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project

    11 parts52CC0-1.0
  • 4 layers90 × 75 mmCM4 2 Backup, the printed circuit board in 3D

    CM4 2 Backup

    olvint/CM4-NAS-MiniPCIE

    Raspberry Pi CM4 based NAS solution board

    21 parts51
  • 4 layers73.9 × 84.5 mmAei, the printed circuit board in 3D

    Aei

    Severson-Group/AMDC-Hardware

    Circuit board designs for controlling advanced motor systems

    54 parts51
  • 2 layers99 × 60 mmPwr, the printed circuit board in 3D

    Pwr

    mfkiwl/KiwiSDR_PCB

    KiCAD PCB files for KiwiSDR project including active antenna and bias tee

    64 parts46

Questions

How big is the Mr Radar Kit PCB?

It measures 52.8 × 37.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Mr Radar Kit use?

14 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Mr Radar Kit KiCad files?

From the skinnyrad/Mr-Radar repository on GitHub, at the commit this page was made from: the board is hardware/Mr_Radar_Kit.kicad_pcb and its schematic hardware/Mr_Radar_Kit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Mr Radar Kit design in my own project?

Its repository states no licence, so its author keeps all rights: ask skinnyrad before reusing the design.