Skip to the content
4 layers25.5 × 27 mmJlink adapter, the printed circuit board in 3D

Small, Custom Tools for Electronics

Size
25.5 × 27 mm
Copper layers
4
Thickness
1.6 mm
Parts
13
Nets
24
Pads
57
Tracks, vias
64, 8
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
10 Aug 2023
Updated
18 Oct 2026

Overview

Jlink adapter is an open-source printed circuit board by SK-Electronics-Consulting, from the SK-Electronics-Consulting/electronics-widgets repository on GitHub. It is a 4-layer board of 25.5 × 27 mm with 13 parts on 24 nets, routed with 64 tracks and 8 vias.

It is built around the BSS123TA and D5V0L1B2WS-7. Its parts include 4 resistors, 3 diodes, 3 connectors and 1 transistor. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

mm8130_rf_cal_kit/README.md

MM8130 RF Calibration Kit

A 1‑ and 2‑port VNA calibration kit presented at the Murata MM8130‑2600RA2 SWF‑type microwave coaxial switch‑connector interface (DC–6 GHz). Use it to calibrate a cable + Murata probe assembly (or a fixture that uses the SWF/MM8130 probe interface) to the probe tip, so the reference plane lands at the connector's center contact.

Status: V1, 2‑layer, ready for OSH Park. Design‑rule clean (0 DRC, 0 ERC, 0 schematic‑parity).

⚠️ AI‑generated design. This schematic and PCB layout were produced with AI assistance. Review every connection, value, footprint, and dimension against the datasheets before ordering or trusting it. The schematic and the board silkscreen carry the same warning.

Top render

Standards included (SOLT)

All standards sit on one non‑separable board. Each is an MM8130 receptacle with the standard element placed right at the RF contact. The Murata probe, when inserted, opens the connector's internal switch and contacts pin 1 (IN) — so every standard is defined between IN and GND.

RefStandardImplementation
J1OpenIN left unterminated (open); defined by the connector's fringing C.
J2ShortIN tied to the connector's own shell‑ground pads with short, wide copper + a ground via.
J3+R1Load50.0 Ω precision thin‑film RF resistor (Stackpole RNCQ 0603, HF) from IN to GND, placed at the contact.
J4↔J5Thru~50 Ω coplanar‑waveguide line, 5.18 mm IN‑to‑IN, between two MM8130s.

The switched OUT pin (pin 2) of every connector is intentionally left unconnected — the internal switch isolates it from IN while a probe is inserted, so loading it would only add a stub.

The connector (MM8130‑2600RA2)

  • Murata SWF‑type microwave coaxial connector with switch, 50 Ω, DC–6 GHz, 2.5 × 2.5 × 1.4 mm.
  • Normally the internal mechanical switch connects IN→OUT (signal passes through). Inserting a Murata probe breaks that path and connects the probe to IN. That is why all standards are referenced to IN.
  • Pinout: 1 = IN (center RF contact, probe‑contacted), 2 = OUT (switched), 3 = GND (shell, 4 lands).
  • LCSC C167503, DigiKey 490‑4981‑1‑ND, Mouser 81‑MM8130‑2600RA2.

Footprint

Custom footprint MM8130:MM8130-2600RA2 (in the project's MM8130.pretty), built from Murata catalog O30E ("Standard Pattern Dimension") and cross‑checked pad‑for‑pad against the vendor land pattern (LCSC C167503). Copper lands: two 0.50 × 0.58 mm signal pads (IN/OUT) on the center axis at ±1.16 mm, and four 0.75 × 0.80 mm ground lands at (±1.025, ±0.95) mm — reproducing the catalog's 2.80 mm ground span / 1.30 mm signal gap / 2.90 mm signal span.

Board / fabrication — OSH Park 2‑layer

  • Board size ≈ 46.5 × 15.0 mm, rounded rectangle with 3 mm corner fillets. Connector pitch is ~8 mm; the Thru pair is ~7.5 mm apart. Standards are probed one at a time during a cal, so the tighter spacing is fine — just confirm your specific Murata probe body clears a neighbour when inserted.
  • 2 × M3 mounting holes (3.2 mm, non‑plated) at the lower‑left and lower‑right corners (H1, H2), centred in the corner fillets, in a clear band below the connectors so screw heads/standoffs stay out of the probe area.

Using the kit (SOLT)

  1. Terminate your VNA cable with the mating Murata SWF probe (Murata O30E p.23 lists the probes).
  2. In the VNA's cal‑kit definition, enter the standard models:
    • Open: characterize the open capacitance (C0…C3) — the MM8130 open is not an ideal open.
    • Short: offset‑short with the small residual inductance of the via/copper.
    • Load: 50 Ω; the Stackpole RNCQ 0603 HF resistor is good but not a perfect broadband load — characterize if you need <‑30 dB return loss near 6 GHz.
    • Thru: one‑way delay ≈ 30 ps for the 5.18 mm CPW line (plus the two connector transitions). Measure it for the exact electrical length/loss.
  3. PCB standards are secondary standards — for best accuracy, characterize each one against a known‑good reference and store the measured models.

Next‑version ideas / caveats

  • The load uses an 0603 (chosen for easy hand‑soldering). It has more parasitic reactance than an 0402/0201, so characterize the load if you need high accuracy near 6 GHz; drop to 0402/0201 and shorten the stub for a better HF load.
  • If you want tight Thru impedance, a 4‑layer controlled‑impedance build (thin top dielectric) is the better route; on 2‑layer, keep the Thru as a characterized reference rather than a precise standard.
  • Characterize and label each standard with its measured model.

Sources

Parts

13
QtyValueFootprintReferences
21kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR1, R2
2Jumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP1, JP2
1100Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR3
1100kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR4
1BSS123TAPackage_TO_SOT_SMD:SOT-23Q1
1Conn_02x05_Odd_EvenJLink-adapter:PinHeader_2x05_P1.27mm_Vertical_comb_SMT_THJ2
1Conn_02x10_Odd_EvenJLink-adapter:PinSocket_2x10_P2.54mm_Horizontal_clipped_silkscreenJ1
1D5V0L1B2WS-7Diode_SMD:D_SOD-323_HandSolderingD3
1RedLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD2
1Tag-Connect IDCConnector_IDC:IDC-Header_2x03_P2.54mm_VerticalJ3
1YellowLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1

More from SK-Electronics-Consulting/electronics-widgets

12
  • 4 layers82 × 40 mmGridfinity USB hub, the printed circuit board in 3D

    Gridfinity USB hub

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    124 parts1
  • 4 layers76 × 54 mmPixelblaze battery backpack, the printed circuit board in 3D

    Pixelblaze battery backpack

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    112 parts1
  • 4 layers70 × 70 mmHUSB238A Dev Board, the printed circuit board in 3D

    HUSB238A Dev Board

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    44 parts1
  • 4 layers11.1 × 40.5 mmSAO tree ornament, the printed circuit board in 3D

    SAO tree ornament

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    23 parts1
  • 4 layers25 × 25.5 mmQwiic CAN Saleae Adapter, the printed circuit board in 3D

    Qwiic CAN Saleae Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    15 parts1
  • 2 layers46.5 × 15 mmMm8130 rf cal kit, the printed circuit board in 3D

    Mm8130 rf cal kit

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    9 parts1
  • 2 layers28.5 × 17 mmCR2032 battery load tester, the printed circuit board in 3D

    CR2032 battery load tester

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    5 parts1
  • 2 layers7.5 × 10 mmREF33xx Breadboard Adapter, the printed circuit board in 3D

    REF33xx Breadboard Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    4 parts1
  • 2 layers9.3 × 13.3 mmRasPi Power Adapter, the printed circuit board in 3D

    RasPi Power Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    3 parts1

Similar boards

  • 4 layers100 × 66.1 mmDriver v1, the printed circuit board in 3D

    Driver v1

    nmk456/gamma-spectrometer

    Tested on Python 3.13, should work on >=3.9

    92 parts1
  • 4 layers100 × 106 mmDelivery robot 1, the printed circuit board in 3D

    Delivery robot 1

    ECE49022Team22/delivery-robot-pcb

    Delivery robot KiCad PCB project and reusable 3.3 V LDO module

    181 parts
  • 4 layers39.2 × 28.4 mmSensorstick, the printed circuit board in 3D

    Sensorstick

    SamanHushi/sensorstick_minimal

    25 parts
  • 4 layers131.5 × 13 mmPower r2, the printed circuit board in 3D

    Power r2

    4lml4/LED_Glasses

    New public repo for work on LED Glasses

    55 parts2
  • 4 layers31.6 × 84.1 mmMCL68, the printed circuit board in 3D

    MCL68

    MicroCoreLabs/Projects

    Ted Fried's MicroCore Labs Projects - FPGA CPU cores and emulators for the 8088, 8086, 8051, 6502, 68000, Z80, Risc-V, and also Typewriter and EPROM Emulator projects.

    13 parts534
  • 4 layers33 × 32 mmDoorman slot programmer, the printed circuit board in 3D

    Doorman slot programmer

    AzonInc/Doorman

    ESP32-S3 based Intercom Gateway (TCS / Koch / Niko / Scantron / Analogue Systems)

    13 parts252GPL-3.0
  • 4 layers25 × 20.5 mmRefclk breakout, the printed circuit board in 3D

    Refclk breakout

    loxodes/vna

    Under development open hardware microwave vector network analyzer

    13 parts205
  • 4 layers59 × 20 mmPmod mmcx, the printed circuit board in 3D

    Pmod mmcx

    azonenberg/starshipraider

    Open hardware test equipment

    13 parts193BSD-3-Clause

Questions

How big is the Jlink adapter PCB?

It measures 25.5 × 27 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Jlink adapter use?

13 parts, built around the BSS123TA and D5V0L1B2WS-7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Jlink adapter KiCad files?

From the SK-Electronics-Consulting/electronics-widgets repository on GitHub, at the commit this page was made from: the board is jlink-adapter-PCB/jlink-adapter.kicad_pcb and its schematic Breadboard Power Supply Adapter/Breadboard Power Supply Adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Jlink adapter design in my own project?

Its repository states no licence, so its author keeps all rights: ask SK-Electronics-Consulting before reusing the design.