Skip to the content
4 layers70 × 70 mmHUSB238A Dev Board, the printed circuit board in 3D

Small, Custom Tools for Electronics

Size
70 × 70 mm
Copper layers
4
Thickness
1.6 mm
Parts
44
Nets
30
Pads
175
Tracks, vias
221, 68
Pours
7
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
10 Aug 2023
Updated
18 Oct 2026

Overview

HUSB238A Dev Board is an open-source printed circuit board by SK-Electronics-Consulting, from the SK-Electronics-Consulting/electronics-widgets repository on GitHub. It is a 4-layer board of 70 × 70 mm with 44 parts on 30 nets, routed with 221 tracks and 68 vias.

It is built around the LMR14006YDDCR, HUSB238A-BB001-QN16R and ME6211C33M5G-N, with the HMK212BC7105KGHTE, FS32X106K101EGG and RC0402FR-10KL among its other parts. Its parts include 11 resistors, 9 capacitors, 6 connectors, 3 ICs and 3 diodes. It belongs with the microcontroller boards boards of this library.

Main components

12

README

mm8130_rf_cal_kit/README.md

MM8130 RF Calibration Kit

A 1‑ and 2‑port VNA calibration kit presented at the Murata MM8130‑2600RA2 SWF‑type microwave coaxial switch‑connector interface (DC–6 GHz). Use it to calibrate a cable + Murata probe assembly (or a fixture that uses the SWF/MM8130 probe interface) to the probe tip, so the reference plane lands at the connector's center contact.

Status: V1, 2‑layer, ready for OSH Park. Design‑rule clean (0 DRC, 0 ERC, 0 schematic‑parity).

⚠️ AI‑generated design. This schematic and PCB layout were produced with AI assistance. Review every connection, value, footprint, and dimension against the datasheets before ordering or trusting it. The schematic and the board silkscreen carry the same warning.

Top render

Standards included (SOLT)

All standards sit on one non‑separable board. Each is an MM8130 receptacle with the standard element placed right at the RF contact. The Murata probe, when inserted, opens the connector's internal switch and contacts pin 1 (IN) — so every standard is defined between IN and GND.

RefStandardImplementation
J1OpenIN left unterminated (open); defined by the connector's fringing C.
J2ShortIN tied to the connector's own shell‑ground pads with short, wide copper + a ground via.
J3+R1Load50.0 Ω precision thin‑film RF resistor (Stackpole RNCQ 0603, HF) from IN to GND, placed at the contact.
J4↔J5Thru~50 Ω coplanar‑waveguide line, 5.18 mm IN‑to‑IN, between two MM8130s.

The switched OUT pin (pin 2) of every connector is intentionally left unconnected — the internal switch isolates it from IN while a probe is inserted, so loading it would only add a stub.

The connector (MM8130‑2600RA2)

  • Murata SWF‑type microwave coaxial connector with switch, 50 Ω, DC–6 GHz, 2.5 × 2.5 × 1.4 mm.
  • Normally the internal mechanical switch connects IN→OUT (signal passes through). Inserting a Murata probe breaks that path and connects the probe to IN. That is why all standards are referenced to IN.
  • Pinout: 1 = IN (center RF contact, probe‑contacted), 2 = OUT (switched), 3 = GND (shell, 4 lands).
  • LCSC C167503, DigiKey 490‑4981‑1‑ND, Mouser 81‑MM8130‑2600RA2.

Footprint

Custom footprint MM8130:MM8130-2600RA2 (in the project's MM8130.pretty), built from Murata catalog O30E ("Standard Pattern Dimension") and cross‑checked pad‑for‑pad against the vendor land pattern (LCSC C167503). Copper lands: two 0.50 × 0.58 mm signal pads (IN/OUT) on the center axis at ±1.16 mm, and four 0.75 × 0.80 mm ground lands at (±1.025, ±0.95) mm — reproducing the catalog's 2.80 mm ground span / 1.30 mm signal gap / 2.90 mm signal span.

Board / fabrication — OSH Park 2‑layer

  • Board size ≈ 46.5 × 15.0 mm, rounded rectangle with 3 mm corner fillets. Connector pitch is ~8 mm; the Thru pair is ~7.5 mm apart. Standards are probed one at a time during a cal, so the tighter spacing is fine — just confirm your specific Murata probe body clears a neighbour when inserted.
  • 2 × M3 mounting holes (3.2 mm, non‑plated) at the lower‑left and lower‑right corners (H1, H2), centred in the corner fillets, in a clear band below the connectors so screw heads/standoffs stay out of the probe area.

Using the kit (SOLT)

  1. Terminate your VNA cable with the mating Murata SWF probe (Murata O30E p.23 lists the probes).
  2. In the VNA's cal‑kit definition, enter the standard models:
    • Open: characterize the open capacitance (C0…C3) — the MM8130 open is not an ideal open.
    • Short: offset‑short with the small residual inductance of the via/copper.
    • Load: 50 Ω; the Stackpole RNCQ 0603 HF resistor is good but not a perfect broadband load — characterize if you need <‑30 dB return loss near 6 GHz.
    • Thru: one‑way delay ≈ 30 ps for the 5.18 mm CPW line (plus the two connector transitions). Measure it for the exact electrical length/loss.
  3. PCB standards are secondary standards — for best accuracy, characterize each one against a known‑good reference and store the measured models.

Next‑version ideas / caveats

  • The load uses an 0603 (chosen for easy hand‑soldering). It has more parasitic reactance than an 0402/0201, so characterize the load if you need high accuracy near 6 GHz; drop to 0402/0201 and shorten the stub for a better HF load.
  • If you want tight Thru impedance, a 4‑layer controlled‑impedance build (thin top dielectric) is the better route; on 2‑layer, keep the Thru as a characterized reference rather than a precise standard.
  • Characterize and label each standard with its measured model.

Sources

Parts

44
QtyValueFootprintReferences
41uCapacitor_SMD:C_0805_2012MetricC3, C5, C8, C9
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
310uCapacitor_SMD:C_1210_3225MetricC1, C6, C7
3DNPResistor_SMD:R_0402_1005MetricR1, R2, R7
3TestPointTestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mmTP1, TP2, TP4
210kResistor_SMD:R_0402_1005MetricR4, R8
22.2kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR9, R10
2820kResistor_SMD:R_0402_1005MetricR5, R6
2Conn_01x06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ4, J5
10.1uCapacitor_SMD:C_0603_1608MetricC2
110uHInductor_SMD:L_KOHERelec_MDA7030L1
112VDiode_SMD:D_SOD-123D2
11kResistor_SMD:R_0402_1005MetricR11
122pCapacitor_SMD:C_0402_1005MetricC4
154.9kResistor_SMD:R_0402_1005MetricR3
1B1100Diode_SMD:D_SMAD1
1BlueLED_SMD:LED_0603_1608MetricD3
1Conn_QWIIC_HorizontalConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ6
1DOD50P06Package_TO_SOT_SMD:TO-252-2Q1
1HUSB238APackage_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mmU2
1Jumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mmJP1
1LMR14006Package_TO_SOT_SMD:SOT-23-6U1
1ME6211C33Package_TO_SOT_SMD:SOT-23-5U3
1Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalJ3
1TestPointTestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP3
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1
1USB_DEBUGConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1~Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mmJP2

More from SK-Electronics-Consulting/electronics-widgets

12
  • 4 layers82 × 40 mmGridfinity USB hub, the printed circuit board in 3D

    Gridfinity USB hub

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    124 parts1
  • 4 layers76 × 54 mmPixelblaze battery backpack, the printed circuit board in 3D

    Pixelblaze battery backpack

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    112 parts1
  • 4 layers11.1 × 40.5 mmSAO tree ornament, the printed circuit board in 3D

    SAO tree ornament

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    23 parts1
  • 4 layers25 × 25.5 mmQwiic CAN Saleae Adapter, the printed circuit board in 3D

    Qwiic CAN Saleae Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    15 parts1
  • 4 layers25.5 × 27 mmJlink adapter, the printed circuit board in 3D

    Jlink adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    13 parts1
  • 2 layers46.5 × 15 mmMm8130 rf cal kit, the printed circuit board in 3D

    Mm8130 rf cal kit

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    9 parts1
  • 2 layers28.5 × 17 mmCR2032 battery load tester, the printed circuit board in 3D

    CR2032 battery load tester

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    5 parts1
  • 2 layers7.5 × 10 mmREF33xx Breadboard Adapter, the printed circuit board in 3D

    REF33xx Breadboard Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    4 parts1
  • 2 layers9.3 × 13.3 mmRasPi Power Adapter, the printed circuit board in 3D

    RasPi Power Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    3 parts1

Similar boards

  • 2 layers38.5 × 27.5 mmUsbc2dell, the printed circuit board in 3D

    Usbc2dell

    H3wastooshort/usbc2dell

    USB-C PD to Dell Barrel-Jack adapter

    30 partsGPL-3.0
  • 4 layers100 × 90 mmOSBAMS Rev2 RC1, the printed circuit board in 3D

    OSBAMS Rev2 RC1

    hle12345/OSBAMS

    Moved here on 2026-10-01. The Rev.1 80x80 mm carrier PCB is a proven-prototype reference (circuits and interfaces that worked), not a design to revise or manufacture.

    149 partsMIT
  • 4 layers36.9 × 36.9 mmFpv flight controller, the printed circuit board in 3D

    Fpv flight controller

    stefanpopovic-dev/fpv-flight-controller

    An open-hardware, 4-layer FPV flight controller board built around the STM32F405RGT6, designed in KiCad. Currently at hardware revision REV3. Designed to run Betaflight.

    111 partsCERN-OHL-S-2.0
  • 4 layers82.1 × 80.2 mmSeguidor de linhas 4camada2-2026-1, the printed circuit board in 3D

    Seguidor de linhas 4camada2-2026-1

    wvianna/mcp-kicad-vscode

    Workspace que combina um servidor MCP para automação de design de PCB com KiCad e o projeto de hardware (placa de circuito impresso) desenvolvido com ele.

    97 parts
  • 4 layers110 × 90 mmUsb hub 3s, the printed circuit board in 3D

    Usb hub 3s

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    116 parts3MIT
  • 2 layers58.5 × 88 mmFugu2, the printed circuit board in 3D

    Fugu2

    fl4p/Fugu2

    Links: git | kicanvas | cadlab | docs | pdf schematics | IBOM (TODO) | firmware | additional docs & resources

    147 parts24
  • 2 layers35 × 38.7 mmRpi2040-lcd gauge, the printed circuit board in 3D

    Rpi2040-lcd gauge

    fharold/rpi2040-lcd-gauge

    Basic and versatile gauges based on the WAVESHARE RP2040-LCD-1.28 module. A small HAT enhances it:

    52 parts
  • 4 layers100 × 60 mmGigaDFN56, the printed circuit board in 3D

    GigaDFN56

    kaminaris/GigaESC-DFN5x6

    Compact, modular three-phase ESC power board for the GigaESC project. Designed in KiCad 10 on a 100 × 60 mm, four-layer PCB, with separate plug-in control and power-supply boards.

    234 parts

Questions

How big is the HUSB238A Dev Board PCB?

It measures 70 × 70 mm and has 4 copper layers, 1.6 mm thick.

What parts does the HUSB238A Dev Board use?

44 parts, built around the LMR14006YDDCR, HUSB238A-BB001-QN16R, ME6211C33M5G-N and HMK212BC7105KGHTE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the HUSB238A Dev Board KiCad files?

From the SK-Electronics-Consulting/electronics-widgets repository on GitHub, at the commit this page was made from: the board is HUSB238A_Dev_Board/HUSB238A_Dev_Board.kicad_pcb and its schematic Breadboard Power Supply Adapter/Breadboard Power Supply Adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the HUSB238A Dev Board design in my own project?

Its repository states no licence, so its author keeps all rights: ask SK-Electronics-Consulting before reusing the design.