shm-dmitry/auto_close_window1This IOT project allows you to open and close your window from any smart house. For example - you can setup rules like a "If night and noise greater then expected -> close window" and "Noise reduced -> open window"
Handle module is an open-source printed circuit board by shm-dmitry, from the shm-dmitry/auto_close_window repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 80 × 42 mm with 114 parts on 77 nets, routed with 534 tracks and 68 vias.
It is built around the ATMEGA328-AU, INA219AID and AMS1117-5.0, with the IRLML0030, BAT760 and IRLML5203 among its other parts. Its parts include 33 capacitors, 29 resistors, 11 transistors, 9 diodes and 6 ICs. It belongs with the home automation and IoT and robots and motor control boards and the ESP32 and AVR (ATmega, ATtiny) boards of this library.
This project allows auto-open and auto-close your windows. Project consists schematics of 3 modules and firmware for 2 controllers
Project re-started
| Hardware | status |
|---|---|
| Indoor schema :: near-handle module | no |
| Indoor schema :: servo module | no |
| Indoor schema :: digital channel to outdoor schema | no |
| Outdoor module schema :: microcontroller and its periphery | no |
| Outdoor module schema :: sensors | no |
| Board | status |
|---|---|
| Indoor board :: near-handle module | no |
| Indoor board :: servo module | no |
| Outdoor module board | no |
| Firmware | status |
|---|---|
| Indoor firmware :: hardware sensors - hall, switch and soft lock | no |
| Indoor firmware :: buttons | no |
| Indoor firmware :: servo control and calibration | no |
| Indoor firmware :: led indication | no |
| Indoor firmware :: controller | no |
| Outdoor firmware :: BMP280 | no |
| Outdoor firmware :: SGP30 | no |
| Outdoor firmware :: Noise sensor | no |
| Outdoor firmware :: Sensor value filters and controller | no |
| Outdoor firmware :: Data transmitter | no |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100 nF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C9, C10, C11, C17, C20, C21, C23, C29, C30, C31, C33 |
| 12 | 10K | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R6, R7, R9, R10, R16, R18, R19, R24 |
| 8 | IRLML0030 | Package_TO_SOT_SMD:SOT-23 | Q3, Q4, Q5, Q7, Q8, Q9, Q10, Q11 |
| 6 | 10 | Resistor_SMD:R_0805_2012Metric | R21, R22, R25, R27, R28, R29 |
| 6 | 2.2 uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C8, C12, C22, C24 |
| 6 | 22 uF | Capacitor_SMD:C_1210_3225Metric | C7, C13, C15, C27, C28, C32 |
| 5 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4, H5 |
| 4 | BAT760 | Diode_SMD:D_SOD-323F | D2, D3, D4, D5 |
| 3 | IRLML5203 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q6 |
| 2 | 0.01 R | Resistor_SMD:R_1206_3216Metric | R17, R26 |
| 2 | 100 uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C5, C6 |
| 2 | 15 pF | Capacitor_SMD:C_0603_1608Metric | C18, C19 |
| 2 | 15MQ030NPBF | Diode_SMD:D_SMA | D6, D8 |
| 2 | 3A | Library:FuseHolder1808 | F1, F2 |
| 2 | 3K9 | Resistor_SMD:R_0805_2012Metric | R14, R15 |
| 2 | 47 nF | Capacitor_SMD:C_0603_1608Metric | C16, C25 |
| 2 | KLS7-TS3601-5.0-180 | Library:SW_PUSH_P6.5_W3.5 | SW1, SW2 |
| 2 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT2, NT3 |
| 1 | +5V | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | 1 nF | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 2*LiFePo4@18650@1800mAh, 6,4V | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | 2K2 | Resistor_SMD:R_0805_2012Metric | R23 |
| 1 | 3K3 | Resistor_SMD:R_0805_2012Metric | R20 |
| 1 | 4.7 uF | Capacitor_SMD:C_0603_1608Metric | C26 |
| 1 | 45K | Resistor_SMD:R_0805_2012Metric | R12 |
| 1 | 5 | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | 5R | Resistor_SMD:R_0805_2012Metric | R8 |
| 1 | 620 | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | ACDET | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | ACDRV | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | ACOK | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | AGND/PGND | NetTie:NetTie-2_SMD_Pad2.0mm | NT1 |
| 1 | AMPLF0630, 8,2uH | Inductor_SMD:L_Abracon_ASPI-0630LR | L1 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | ATmega328-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U3 |
| 1 | BQ24780S | Package_DFN_QFN:QFN-28-1EP_4x4mm_P0.4mm_EP2.6x2.6mm_ThermalVias | U5 |
| 1 | CHG SUPPLY | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | Charger | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | ES2J | Diode_SMD:D_SMB | D9 |
| 1 | GND | Library:TestPoint_Plated_Hole_D1.0mm | TP2 |
| 1 | HC-49U, 8MHz | Crystal:Crystal_HC49-U_Vertical | X1 |
| 1 | INA219 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | JVR-05N180M | Varistor:RV_Disc_D7mm_W4.5mm_P5mm | RV1 |
| 1 | PROCHOT#_EN | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | SMAJ26A | Diode_SMD:D_SMA | D7 |
| 1 | SRX882@443MHz | Library:SRX882_Vertical | U2 |
| 1 | STX882@443MHz | Library:STX882_Vertical | U1 |
| 1 | USBASP | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J3 |
| 1 | VSYS | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | red/green, common cathode, F3 | LED_THT:LED_D5.0mm-3 | D1 |
It measures 80 × 42 mm and has 4 copper layers, 1.6 mm thick.
114 parts, built around the ATMEGA328-AU, INA219AID, AMS1117-5.0 and IRLML0030. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the shm-dmitry/auto_close_window repository on GitHub, at the commit this page was made from: the board is schematics/handle-module/handle-module.kicad_pcb and its schematic schematics/handle-module/handle-module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
shm-dmitry/auto_close_window
This IOT project allows you to open and close your window from any smart house. For example - you can setup rules like a "If night and noise greater then expected -> close window" and "Noise reduced -> open window"
shm-dmitry/auto_close_window
This IOT project allows you to open and close your window from any smart house. For example - you can setup rules like a "If night and noise greater then expected -> close window" and "Noise reduced -> open window"
kenyattaejones32-boop/AQM
Open-source hardware design for OpenHAP, an ESP32-based air quality monitor with CO sensing, thermistor temperature input, USB-C charging, and cellular data upload.
kenyattaejones32-boop/Gasmat_Gateway
KiCad 8 hardware design for the Gasmat Gateway board (Geviton).
stan23/myPCBs
Verschiedene Platinen für HomeMatic, AskSinPP und SmartHome
rapha-tech/ESP32-hema-console
New PCB for the small console from hema to use an ESP32
pipipipi2002/stm32f446vetx-dev-module
Dev Module for STM32F446VETx