Skip to the content
2 layers54.6 × 61.1 mmAlto ethernet interface, the printed circuit board in 3D

Alto ethernet interface

shirriff/alto-ethernet-interface15

Interface to Xerox Alto's 3 Mb/s Ethernet

Size
54.6 × 61.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
88
Pads
130
Tracks, vias
51, 0
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
12 Oct 2017
Updated
28 May 2020

Overview

Alto ethernet interface is an open-source printed circuit board by shirriff, from the shirriff/alto-ethernet-interface repository on GitHub, published under the AGPL-3.0 licence. It is a 2-layer board of 54.6 × 61.1 mm with 11 parts on 88 nets, routed with 51 tracks and 0 vias.

It is built around the RJ45. Its parts include 4 resistors, 3 capacitors, 3 connectors and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

board/README.md

Instructions for building the v3 board

The v3 board works as is. This board fixes a missing trace in v2. The v1 board is not software compatible with the v2/v3 coards.

The board was designed with KiCad. This directory contains the KiCad files. The board can be ordered from OshPark here.

Materials

  • 7438 open-collector NAND gate.
  • 2 x 2x23 Male Headers
  • C2, C3: 2 x 0.1uF ceramic capacitor
  • R3: 120 ohm resistor
  • R4: 330 ohm resistor
  • Ethernet connector: through-hole, PCB mount RJ45
  • DB25 male to RJ45 female modular adapter kit (ADM-25M8-BK)
  • Ethernet cable
  • BeagleBone Black + power supply + network connection (e.g. Apple Thunderbolt to Ethernet)

Note: R1/R2/C1 in the middle of the board are unused. They were provided in case a pullup/down was needed.

DB25 connector wiring

  • 3 Blue

  • 16 Orange

  • 8 Red

  • 20 Green

  • 12 Yellow

  • 24 Black

  • 13 White

  • 25 Brown

Insert pins from back. Pin 1 is left on the wider side. Push pins in until they click. You can twist the pairs of wires together if you want.

text

(L = blue, N = brown, K = black)

Testing

Output signal to Alto can be measured across pins 7 and 3 of the IC (pin 7 = ground). When connected to Alto, signal should be idle low (0.2V), pulsing to 3.5V. Can be a bit of overshoot, but shouldn't be ringing. When disconnected from Alto, signal should go between 0V and 5V.

Input signal from Alto can be measured across the right hand side of a resistor. Signal should be idle high (2.2V) pulsing to 0V.

LEDS

0 = top, 3 = closest to Ethernet port. 0 and 3 should flash every 2 seconds for Breath-of-life packet. Others should flash during network boot or other network traffic. If LED 0 is stuck on, reboot the BeagleBone. (There's something wrong with the gateway.)

At the end of a disk boot, LED 1 should flash a couple times (as the Alto does a couple network requests).

Parts

11
QtyValueFootprintReferences
20.1uFCapacitors_ThroughHole:C_Disc_D3.0mm_W1.6mm_P2.50mmC2, C3
2BeagleBone_Black_HeaderSocket_BeagleBone_Black:Socket_BeagleBone_BlackP8, P9
2unusedSparkFun:AXIAL-0.3R1, R2
1120SparkFun:AXIAL-0.3R3
1330SparkFun:AXIAL-0.3R4
17438Housings_DIP:DIP-14_W7.62mmU1
1RJ45Connect:RJ45_8J1
1unusedCapacitors_ThroughHole:C_Disc_D3.0mm_W1.6mm_P2.50mmC1

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 4 layers84 × 82 mmToad, the printed circuit board in 3D

    Toad

    travisgoodspeed/goodfet

    An embedded bus adapter for various microcontrollers and radios.

    241 parts333
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99
  • 2 layers50 × 55.4 mmCasserole, the printed circuit board in 3D

    Casserole

    puddly/casserole

    Control GE appliances

    23 parts94Apache-2.0
  • 2 layers67.9 × 47.8 mmPlatine, the printed circuit board in 3D

    Platine

    nv1t/standing-desk-interceptor

    I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project

    11 parts52CC0-1.0
  • 4 layers90 × 75 mmCM4 2 Backup, the printed circuit board in 3D

    CM4 2 Backup

    olvint/CM4-NAS-MiniPCIE

    Raspberry Pi CM4 based NAS solution board

    21 parts51
  • 4 layers73.9 × 84.5 mmAei, the printed circuit board in 3D

    Aei

    Severson-Group/AMDC-Hardware

    Circuit board designs for controlling advanced motor systems

    54 parts51
  • 2 layers99 × 60 mmPwr, the printed circuit board in 3D

    Pwr

    mfkiwl/KiwiSDR_PCB

    KiCAD PCB files for KiwiSDR project including active antenna and bias tee

    64 parts46

Questions

How big is the Alto ethernet interface PCB?

It measures 54.6 × 61.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Alto ethernet interface use?

11 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Alto ethernet interface KiCad files?

From the shirriff/alto-ethernet-interface repository on GitHub, at the commit this page was made from: the board is board/board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Alto ethernet interface design in my own project?

Its repository publishes it under the AGPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).