Skip to the content
2 layers309 × 104.1 mmAbomination, the printed circuit board in 3D

Split keyboard with trackpad

Size
309 × 104.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
103
Nets
94
Pads
541
Tracks, vias
549, 70
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
14 Oct 2023
Updated
20 Oct 2023

Overview

Abomination is an open-source printed circuit board by sebastian-stumpf, from the sebastian-stumpf/abomination repository on GitHub. It is a 2-layer board of 309 × 104.1 mm with 103 parts on 94 nets, routed with 549 tracks and 70 vias.

It is built around the 1N4148W. Its parts include 40 diodes, 40 switches, 3 connectors and 2 ICs. It belongs with the keyboards and input boards of this library.

Main components

1

README

README.md

abomination

abomination

Attention

I'm a hobbyist/amateur at best. So there may be things that aren't optimized. That being said I've had the files in the gerbers/ directory manufactured at JLC with 1.6mm thickness and they work just fine with my fork of the qmk repository directory. So if you decide to use this, then please be advised that I'm not providing any sort of liability and you should exercise some caution.

Trackpad

The trackpad relies on the following adapter https://github.com/keyboard-magpie/minimal-fpc-i2c-pcb/ which can cheapily be PCBA'ed. There reasons for using this adapter are that I hate soldering those tiny clamshell connectors and I can easily hot swap the trackpad with an OLED display.

Case

There are two plate versions for the case. The default version is very thin and wobbly and the switches aren't pressed in easily. There's also a 'thick' version of the plates that sits on the pcb rock solid and the switches pop in with ease. I'd heavily recommend the thick version. Just be aware that it will consume about 4 times the material as the thin plate.

BOM

QuantityItemComment
2Helios or Liatris Controller
2IC-Sockets for MCUOptional but recommended
2TRRS Sockets
401N4148 SOD123 diodes
2SKHLLBA010 buttons
36MX Hotswap Sockets
1EC12 Encoders
46mm tactile switchesLonger caps work best
36MX Switches + Keycaps
1Cirque 40mm curved trackpadDesolder R1 for i2c
1i2c adapter PCB for trackpadsee above
1fpc cable for adapter
14 pin dip socket and headerfor the adapter
a lotM2 Screws (flat & countersunk)
also a lotM2 heat inserts
12round bumpons with 3,1mm dia

Firmware

See my fork of the qmk repository. Nothing special here. You can just copy the code over to your own repository and adjust the keymap.

Feedback

I'm always happy to hear your opinions about this and if you decide to build this board then please do send me a picture of it.

Parts

103
QtyValueFootprintReferences
401N4148Wsepp:D_SOD-123D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +24
36MX_SW_HSsepp:SW_MX_HS_1uSW1, SW2, SW10, SW13, SW14, SW15, SW16, SW17, SW20, SW21, SW22, SW23, SW24, SW25, SW26, SW27 +20
10MountingHoleMountingHole:MountingHole_2.2mm_M2_DIN965H1, H2, H3, H4, H5, H6, H8, H9, H14, H15
4actionswitchsepp:actionswitchSW11, SW12, SW18, SW19
4mousebitessepp:breakaway-mousebitesH7, H10, H11, H12
2Liatrismarbastlib-xp-promicroish:Liatris_AH_USBdnU1, U2
2MJ-4PP-9sepp:MJ-4PP-9J1, J2
2SW_Pushmarbastlib-various:SW_SKHLLCA010L_RST1, R_RST1
1Conn_01x04_Pinsepp:fpc-breakcout-connectorJ3
1RotaryEncoderRotary_Encoder:RotaryEncoder_Alps_EC12E_Vertical_H20mmL_ROT1
1Trackpad-Holdersepp:abimination-trackpad-holderH13

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers208.8 × 396.9 mmFerris, the printed circuit board in 3D

    Ferris

    pierrechevalier83/ferris

    A low profile split keyboard designed to satisfy one single use case elegantly

    145 parts1.3k
  • 2 layers285.5 × 95 mmReviung46 ver1 1, the printed circuit board in 3D

    Reviung46 ver1 1

    gtips/reviung

    The REVIUNG41 is 41-key column staggered keyboard.

    119 parts517MIT
  • 4 layers95.6 × 73.6 mmMathpad, the printed circuit board in 3D

    Mathpad

    Summa-Cogni/Mathpad

    A mathematical keypad for students and professionals

    93 parts243
  • 2 layers141.5 × 83 mmRolio, the printed circuit board in 3D

    Rolio

    MickiusMousius/Rolio46Keyboard

    A split wireless keyboard based on the Corne and Sofle

    110 parts236MIT
  • 6 layers160 × 100 mmAdrmu6layer, the printed circuit board in 3D

    Adrmu6layer

    marcoreps/ADRmu

    ADR1000 10V standard

    240 parts149
  • 2 layers99.1 × 90.7 mmBgkeeb, the printed circuit board in 3D

    Bgkeeb

    sadekbaroudi/bgkeeb

    This is a reversible 100mm x 100mm pcb with support for mx or choc switches (no hotswap), per key led, rotary encoders, and exposes the SDA/SCL/GND/VCC lines in the form of the pimoroni trackball pins (meaning you can…

    108 parts108
  • 2 layers229.8 × 102.6 mmBw2, the printed circuit board in 3D

    Bw2

    hazels-garage/bad-wings

    Bad Wings

    107 parts107CC-BY-SA-4.0

Questions

How big is the Abomination PCB?

It measures 309 × 104.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Abomination use?

103 parts, built around the 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Abomination KiCad files?

From the sebastian-stumpf/abomination repository on GitHub, at the commit this page was made from: the board is pcb/abomination.kicad_pcb and its schematic pcb/abomination.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Abomination design in my own project?

Its repository states no licence, so its author keeps all rights: ask sebastian-stumpf before reusing the design.