2 layers34.5 × 14.2 mm
2 layers34.5 × 14.2 mm
Can Module
scottcjx/Can-Module- Size
- 34.5 × 14.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 11
- Nets
- 20
- Pads
- 50
- Tracks, vias
- 87, 21
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 8 Dec 2023
- Updated
- 20 Dec 2023
Overview
Can Module is an open-source printed circuit board by scottcjx, from the scottcjx/Can-Module repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 34.5 × 14.2 mm with 11 parts on 20 nets, routed with 87 tracks and 21 vias.
It is built around the SN65HVD230D and MCP2518FD-E/SL. Its parts include 4 capacitors, 2 resistors, 2 ICs, 2 connectors and 1 crystal.
Main components
2
SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
MCP2518FD-E/SL
SOIC-14-40℃~+125℃ 2.7V~5.5V 20mA 8Mbps CAN FD Controller Monitor mode、Low-power mode、Programmable auto retransmission control SPI SOIC-14 CAN Controllers ROHSMicrochip TechnologyCAN Controllers
Parts
11| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100n | Capacitor_SMD:C_0402_1005Metric | C101, C102 |
| 2 | 20p | Capacitor_SMD:C_0402_1005Metric | C103, C104 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R101 |
| 1 | 120 | Resistor_SMD:R_0805_2012Metric | R102 |
| 1 | 40MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y101 |
| 1 | Can Termination | NVF-Kicad:PinHeader_1x02_P2.54mm_Horizontal | J103 |
| 1 | MCP2518FD | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U101 |
| 1 | MCP251X | NVF-Kicad:Can-Module-CM251X | J101 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U102 |
Questions
How big is the Can Module PCB?
It measures 34.5 × 14.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Can Module use?
11 parts, built around the SN65HVD230D and MCP2518FD-E/SL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Can Module KiCad files?
From the scottcjx/Can-Module repository on GitHub, at the commit this page was made from: the board is HDK/CM-2518/Can-Module.kicad_pcb and its schematic HDK/CM-2515/Can-Module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Can Module design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from scottcjx/Can-Module
1Similar boards
- 2 layers48 × 48 mm
- 2 layers65 × 30 mm
CANFDZeroHAT
generationmake/CANFDZeroHAT
Raspberry Pi HAT with Microchip MCP2518FD CAN FD controller
32 parts27 - 4 layers100 × 82 mm
LCC Pico Node v3 0B - 1206
bocabob/LCC-RPi-Pico-Board
KiCad files for a board supporting LCC CAN hardware implementation for RPiPico
89 parts3CERN-OHL-S-2.0 - 4 layers98 × 100 mm
Esp32s3-can sd logger
MrBlahhhh/esp32-shield-can1-can2-kdcan-analogin-sdcard
A carrier board an ESP32-S3-DevKitC-1 plugs into, turning it into a vehicle data logger. The dev board brings the MCU and its power; this board brings everything that has to touch a car.
164 parts1 - 4 layers90 × 56.1 mm
K2-cm5-traeger
Gamecard/k2-plus-cm5
K2 Plus CM5 – Creality K2 Plus mit Upstream-Klipper auf einem Raspberry Pi CM5
137 partsGPL-3.0 - 4 layers110 × 100 mm
Icc gateway prerouting r2
moistpope/fisker-icc-gateway
KiCad 10 project. Sits between the car harness and the ICC (head unit) main connector J1 (Molex stAK50h 160013-0641), passes every circuit straight through except the two CAN buses, which go through a Teensy 4.1 gateway…
70 parts - 4 layers100 × 90 mm
- 2 layers100 × 95 mm
