
Sensorunit
scalinq-lab/cryomagsens
The sensor unit was designed in KiCad 10 and manufactured by JLCPCB. It is built in a flex PCB material to achieve a very small build height, in order to come very close to the device under test.

The sensor unit was designed in KiCad 10 and manufactured by JLCPCB. It is built in a flex PCB material to achieve a very small build height, in order to come very close to the device under test.
Signal processing unit is an open-source printed circuit board by scalinq-lab, from the scalinq-lab/cryomagsens repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 6-layer board of 100.7 × 106.4 mm with 178 parts on 192 nets, routed with 2,017 tracks and 507 vias.
It is built around the AD8675ARZ, AD8421ARZ and AD7175-2BRUZ, with the AD8603AUJ among its other parts. Its parts include 61 capacitors, 47 resistors, 27 ICs, 4 diodes and 4 connectors. It belongs with the RP2040 boards of this library.
(Sensor unit)
The sensor unit was designed in KiCad 10 and manufactured by JLCPCB. It is built in a flex PCB material to achieve
a very small build height, in order to come very close to the device under test. The Flex PCB is mounted to a copper
spine (see ..\mechanical_designs for the full design) for thermalisation purposes. The total build height of the sensor unit is 1.1 mm.
The sensor unit features a AKM HQ0811 InAs Hall element as a magnetic field sensor, a 1N4148 Si diode as a temperature sensor and a 10-pin Molex PicoBlade connector for a good and stable connection.
The Hall element has four nodes, here denoted a, b, c, d. When a current is pushed fron a to c, a potential difference can be measured between b and d, which scales linearly with the applied orthogonal magnetic flux density. When a current is pushed from b to d, a similar potential difference can be measured between a and c. By modulating the current directiion and through which axis the current is pushed, the remaining DC offset due to asymmetries in the element can be eliminated.
The sensor unit also features a 4-wire measurement setup for the diode, which acts as a temperature sensor. The nominal drive current of the diode is 10 µA.
The sensor unit features a presence pin (denoted PRS), which is internally connected to the ground pin on the sensor PCB. When connected to the signal processing unit, a GPIO pin is pulled low through the sensor unit, indicating that a sensor is connected and allowing current output.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 10µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C16, C18, C20, C23, C27, C29, C32, C35, C38, C40, C41, C50, C53, C54, C57 +3 |
| 16 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C19, C21, C22, C28, C30, C33, C34, C37, C39, C42, C44, C46, C51, C52, C55 |
| 9 | ADG1404 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U9, U13, U14, U15, U16, U17, U18, U19, U20 |
| 8 | 47 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R33, R34, R35, R36, R37, R38, R39, R40 |
| 6 | 4,7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C8, C12, C13, C15, C60 |
| 5 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R25, R28, R29, R46, R47 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R24, R41, R42, R43 |
| 4 | 1µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C45, C47, C58, C59 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100 K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R8, R45 |
| 3 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R44 |
| 3 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19, R20, R23 |
| 3 | AD8675ARZ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U7, U8, U22 |
| 3 | ADG1413 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U10, U11, U12 |
| 3 | BAV199-7-F | Package_TO_SOT_SMD:SOT-23-3 | D1, D2, D3 |
| 3 | Conn_01x10_Pin | Connector_Molex:Molex_PicoBlade_53261-1071_1x10-1MP_P1.25mm_Horizontal | J1, J2, J3 |
| 3 | ~ | SPU_custom_footprints:APC817D1SL | U5, U6, U27 |
| 2 | 1,5nF/5KV | Capacitor_SMD:C_1825_4564Metric | C2, C3 |
| 2 | 10 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R30, R31 |
| 2 | 10n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C31, C56 |
| 2 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C24, C25 |
| 2 | 120k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R7 |
| 2 | 2.2uF/100V | Capacitor_SMD:C_1206_3216Metric | C1, C4 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C62, C63 |
| 2 | 25 K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R10 |
| 2 | 470n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11, C14 |
| 2 | 499 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R9 |
| 2 | 7.5k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R5 |
| 2 | AD8421ARZ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U21, U24 |
| 2 | LT3042xMSE | Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm | U3, U4 |
| 2 | LT3094xMSE | Package_SO:MSOP-12-1EP_3x4.039mm_P0.65mm_EP1.651x2.845mm | U1, U2 |
| 1 | +12V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | +12 |
| 1 | +15V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | +15 |
| 1 | +2.5V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | +2.5 |
| 1 | -12V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | -12 |
| 1 | -15V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | -15 |
| 1 | -2.5V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | -2.5 |
| 1 | 0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18 |
| 1 | 0.47 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R32 |
| 1 | 1.6k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R26 |
| 1 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R22 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R27 |
| 1 | 250k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 1 | 3.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21 |
| 1 | 300 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
| 1 | 4.7µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C43 |
| 1 | 47n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C36 |
| 1 | 47nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C26 |
| 1 | 54-00164 | SPU_custom_footprints:DC_plug | J4 |
| 1 | 8.2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 820 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14 |
| 1 | 82k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16 |
| 1 | A | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | A2 |
| 1 | AD7175-2BRUZ | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U23 |
| 1 | AD8603 | Package_TO_SOT_SMD:TSOT-23-5 | U25 |
| 1 | ADS8866 | Package_SO:MSOP-10_3x3mm_P0.5mm | U26 |
| 1 | B | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | B1 |
| 1 | C | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | C61 |
| 1 | CONVST1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | CONVST1 |
| 1 | D | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | D4 |
| 1 | DIN0 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | DIN0 |
| 1 | DIN1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | DIN1 |
| 1 | DOUT0 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | DOUT0 |
| 1 | DOUT1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | DOUT1 |
| 1 | GND1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | GND1 |
| 1 | GND2 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | GND2 |
| 1 | HALL_CURRENT | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | HALL_CURR1 |
| 1 | PWRGND | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | PWRGND1 |
| 1 | RaspberryPi_Pico | footprints:Raspberry_Pi_Pico_mod | A1 |
| 1 | S/E0 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | S/E0 |
| 1 | SCLK0 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | SCLK0 |
| 1 | SCLK1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | SCLK1 |
| 1 | TEMP_I+ | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TEMP_I+1 |
| 1 | TEMP_I- | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TEMP_I-1 |
| 1 | TEMP_V+ | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TEMP_V+1 |
| 1 | TEMP_V- | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TEMP_V-1 |
| 1 | V_HALL+ | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | V_HALL+1 |
| 1 | V_HALL- | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | V_HALL-1 |
| 1 | V_HALL_ADC | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | V_HALL_ADC1 |
| 1 | V_TEMP_ADC | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | V_TEMP_ADC1 |
The 176 most common of 178 parts.

scalinq-lab/cryomagsens
The sensor unit was designed in KiCad 10 and manufactured by JLCPCB. It is built in a flex PCB material to achieve a very small build height, in order to come very close to the device under test.

ShizeChe/unispin
Unified control architecture for spin qubits in quantum dot devices


NSLS2/zupsc-hw
Zynq UltraScale Power Supply Controller hardware


niki100jad/POQUITO_ADCS
ADCS for a PocketQube mission (Warning: Still untested!)


ZeshuLiu/SX-70-Mk2
把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

It measures 100.7 × 106.4 mm and has 6 copper layers, 1.6 mm thick.
178 parts, built around the AD8675ARZ, AD8421ARZ, AD7175-2BRUZ and AD8603AUJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the scalinq-lab/cryomagsens repository on GitHub, at the commit this page was made from: the board is signal_processing_unit_pcb/signal_processing_unit.kicad_pcb and its schematic sensor_unit_pcb/Sensorunit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).