Skip to the content
2 layers95.9 × 27.8 mmOpsx x, the printed circuit board in 3D

把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

Size
95.9 × 27.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
74
Nets
74
Pads
278
Tracks, vias
955, 153
Pours
12
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
3 Jun 2023
Updated
11 Oct 2026

Overview

Opsx x is an open-source printed circuit board by ZeshuLiu, from the ZeshuLiu/SX-70-Mk2 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 95.9 × 27.8 mm with 74 parts on 74 nets, routed with 955 tracks and 153 vias.

It is built around the RP2040, AD8603AUJ and TSL2561T, with the W25Q128JVSIQ, TLV70430DBVR-TD and 1N4148WS among its other parts. Its parts include 35 resistors, 15 capacitors, 6 ICs, 6 diodes and 4 transistors. It belongs with the RP2040 boards of this library.

Main components

8

README

Readme.md

SX-70 Mk2

介绍

针对SX-70 Sonnar相机的现代化改造,在保留原本机身的自动功能的情况下,提供更直接的手动控制方式,能够更加自由地进行拍摄。安装机身控制器后手动控制更加方便
相机正面

相机背面

项目组成

项目中包含几个部分的硬件:

  1. 相机主控板:替换相机机头内原装的控制器,接管相机的控制。
  2. 机身控制器:显示当前相机工作状态并提供用于交互的按键。粘贴在机身背部,不会增加相机高度,因此大部分相机包依旧可以通用,与相机主控板连接需要转接器以及60mm长1.0mm间距的6pin Fpc排线。
  3. 闪光灯接口:(还未实际测试),从原本的闪光灯排上引出3.5mm接口,用于外置闪光灯。
  4. 机身电池:(正在开发中),通过相机底部的两个触点为相机供电,可以使用iType相纸进行拍摄。

开发

PCB部分除闪光灯接口使用嘉立创EDA外均使用KiCad8绘制,仓库提供了相应的工程和光绘(gerber)文件。

Rev1.x - Rev2.x 版本的主控使用RP2040,通过micropython编程。micropython中硬件定时器最小单位为1ms,后续考虑换用C语言获得更高定时器配置精度。

性能参数

相机主控 相机主控可以单独使用,此时可以进行自动测光和曝光,如果需要使用B、T以及手动模式需要配备机身控制器。

快门速度: 1/2000s-1s,支持B门及T门
自拍定时: 3s 5s 10s (可以与T门或B门同时使用减轻机器振动的影响)
测光: 目前软件仅支持600型相纸,自动测光下最低快门速度1/2s
闪光同步: 插入闪光灯后快门组速度自动变为1/30s,在手动模式下可以设置慢于1/30s的快门速度来进行填充闪光。快门速度设置为快于1/30s时将会自动调整至1/30s,机身控制器上将会显示实际使用的快门速度\

SX70的光圈在使用闪光灯时将会根据对焦距离进行收缩,此时调整黑白轮可以控制其光圈大小。本项目依旧保留了该特点,因此在使用闪光灯时请注意对焦距离以及黑白轮的位置

样片

自动测光:

自动测光拍摄

手动曝光:

手动曝光

闪光灯:

闪光灯

1/1000s 快门速度:

1/1000s

硬件制造

光绘(Gerber)文件可以在Fabrication文件夹中找到,必须使用0.8mm以下的PCB制造。需要使用 60mm 长 1mm间距的 6pin fpc软排线连接主板和机身控制器。

软件

把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。
在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将g_main.py命名为 main.py(非常重要,只有这样才能够上电运行)
建议针对自己的快门适当调整代码中快门速度的值,可以使用这个快门速度测试器来测试机器的快门速度,便于调整。

组装

提示:组装需要一些基本的工具:电烙铁、撬棒和镊子。
大多数sx70相机的螺丝都是非常特殊的1mm x 1mm 宝丽来螺丝,拆卸需要特殊的螺丝刀,可以从咸鱼买一把或者自己磨一个。
在操作之前推荐先浏览以下内容Disassembly Guide 或者 SX70 camera 125ASA to 600ASA conversion.

拆卸后对原本主板进行替换即可,如需要机身控制器则将左上角焊盘焊线引出即可通过转接板连接机身控制器。焊接FPC时建议使用含铅(低温)焊锡,否则有损伤机器FPC的风险。只需要将原本的拆掉并且替换上去即可,对于有焊接及机身拆装经验的人来说难度不高。

相关开源软件

  1. 项目受到了OPSX 和openSX70的启发。
  2. Rev1.x - Rev2.x 版本的128x32OLED屏幕代码:micropython-adafruit-ssd1306
  3. 机身控制器按键使用的PCF8575:micropython-pcf8575
  4. Rev1.x-Rev2.x 主控使用的tsl2561光线传感器:micropython-adafruit-tsl256

Parts

74
QtyValueFootprintReferences
10100nCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC1, C2, C6, C7, C8, C9, C10, C11, C12, C14
910kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR4, R6, R9, R11, R12, R13, R15, R17, R19
612kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR5, R10, R14, R16, R18, R20
4100kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR8, R23, R25, R28
41kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR3, R26, R27, R35
3100Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR21, R22, R24
31N4148WSDiode_SMD:D_SOD-323D1, D3, D4
31uCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC3, C5, C13
3Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1, J2, J3
3~OPSX:Selector_defaultZ1, Z2, Z3
227.4Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR1, R2
2AD8603Package_TO_SOT_SMD:TSOT-23-5U5, U6
2LEDDiode_SMD:D_0603_1608Metric_Pad1.05x0.95mm_HandSolderD5, D6
2Q_NMOS_GSDPackage_TO_SOT_SMD:SOT-23Q1, Q2
10.1uCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC4
113pCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC15
1150Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR30
1180Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR29
12.7kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR33
122kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR7
1330Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR34
147kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR32
15.6kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR31
1Crystal_GND2Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mmY1
1MMBT3904Package_TO_SOT_SMD:SOT-23Q4
1OPTICAL-TSL2561T(6P-3.8X2.6MM)OPSX:TMB6-1.55-3.8X2.6MMU4
1Q_PMOS_GSDPackage_TO_SOT_SMD:SOT-23Q3
1RP2040RP2040_minimal:RP2040-QFN-56U1
1SFH2430OptoDevice:Osram_SFH2430D2
1TLV70430DBVRTI_footprints:DBV0005A_NU2
1W25Q128JVSPackage_SO:SOIC-8_5.23x5.23mm_P1.27mmU3
1sx~OPSX:sx70sx1

More from ZeshuLiu/SX-70-Mk2

3
  • 2 layers95.9 × 27.8 mmOpsx x, the printed circuit board in 3D

    Opsx x

    ZeshuLiu/SX-70-Mk2

    把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

    62 parts2GPL-3.0
  • 2 layers65 × 74 mmSx70battery, the printed circuit board in 3D

    Sx70battery

    ZeshuLiu/SX-70-Mk2

    把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

    46 parts2GPL-3.0
  • 2 layers24 × 85.2 mmController body, the printed circuit board in 3D

    Controller body

    ZeshuLiu/SX-70-Mk2

    把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

    31 parts2GPL-3.0

Similar boards

  • 2 layers105.1 × 55.3 mmBMS 1, the printed circuit board in 3D

    BMS 1

    lbrosnan1/quboElectrical

    Stores the KiCAD PCB files for Qubo

    111 parts2
  • 2 layers97.6 × 67.3 mmIO 16x8 matrix, the printed circuit board in 3D

    IO 16x8 matrix

    PPUC/Hardware_IO_16x8_matrix

    Hardware for a Switch Matrix Board for PPUC

    210 parts
  • 4 layers82.5 × 65.5 mmOpenHomeSwitch, the printed circuit board in 3D

    OpenHomeSwitch

    TobleMiner/OpenHomelabSwitch

    297 parts11
  • 2 layers105 × 105 mmGW A, the printed circuit board in 3D

    GW A

    ayaxan7/SolarAlert

    SolarAlert is a compact embedded hardware project designed to monitor the health and performance of solar panels.

    97 parts
  • 4 layers94.4 × 72.8 mmRP2040 base, the printed circuit board in 3D

    RP2040 base

    Twisted-Fields/rp2040-motor-controller

    A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.

    325 parts419
  • 2 layers76 × 63.5 mmPicoTracker, the printed circuit board in 3D

    PicoTracker

    xiphonics/picoTracker-pcb

    Buy the official kit at xiphonics store # Trademark Notice

    98 parts36CC0-1.0
  • 4 layers40 × 58.5 mmPicoFox PCB, the printed circuit board in 3D

    PicoFox PCB

    ai6ym/PicoFox

    The open source fox transmitter.

    143 parts16

Questions

How big is the Opsx x PCB?

It measures 95.9 × 27.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Opsx x use?

74 parts, built around the RP2040, AD8603AUJ, TSL2561T and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Opsx x KiCad files?

From the ZeshuLiu/SX-70-Mk2 repository on GitHub, at the commit this page was made from: the board is Hardwares/MainController/rev1/opsx_x.kicad_pcb and its schematic Hardwares/Body_controller/Rev1/Controller_body/Controller_body.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Opsx x design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).