2 layers76 × 64.5 mm
PicoTracker
xiphonics/picoTracker-pcb
Buy the official kit at xiphonics store # Trademark Notice
14 parts36CC0-1.0
2 layers76 × 63.5 mm
PicoTracker
xiphonics/picoTracker-pcb36Buy the official kit at xiphonics store # Trademark Notice
- Size
- 76 × 63.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 98
- Nets
- 119
- Pads
- 457
- Tracks, vias
- 1,012, 239
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 5 Jun 2023
- Updated
- 29 May 2026
Overview
PicoTracker is an open-source printed circuit board by xiphonics, from the xiphonics/picoTracker-pcb repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 76 × 63.5 mm with 98 parts on 119 nets, routed with 1,012 tracks and 239 vias.
It is built around the RP2040, AP2502KTR-G1 and W25Q128JVSIQ, with the XC6206P332MR, BQ24074RGTR and H11L1 among its other parts. Its parts include 45 capacitors, 21 resistors, 9 ICs, 8 connectors and 2 diodes. It belongs with the RP2040 boards of this library.
Main components
10
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
AP2502KTR-G1
SOT-23-6-40℃~+85℃ 1% 150kHz 20mA 2V~6V 4 Built-in Over-Temperature Protection (OTP) PWM SOT-23-6 LED Drivers ROHSDiodes IncorporatedLED Drivers
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
BQ24074RGTR
QFN-16-EP(3x3)-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.2V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery Management
H11L1
DIP-6-55℃~+100℃ 1 1.6mA 1Mbit/s 250mW 3V~15V 5kV DC DIP-6 Logic Output Optoisolators ROHSEverlight ElectronicsLogic Output Optoisolators
PCM5102APW
TSSOP-20-25℃~+85℃ 1.8V~3.3V 2 32 384kHz 500uA 50MHz Audio Decoder Digital filtering、Power-down mode I2S TSSOP-20 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special Purpose
1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes
FPC-05FB-40PH20
SMD,P=0.5mm,卧贴-25℃~+85℃ 0.3mm 0.5mm 2mm 40P 500mA 50V Double-Sided Contacts, Top and Bottom Entry Hinged Lid Phosphor bronze Surface Mount, Right Angle Tin SMD,P=0.5mm,卧贴 FFC, FPC (Flat Flexible) Connector Assemblies ROHSXUNPUFFC, FPC (Flat Flexible) Connector Assemblies
MS-22D28-G020
SMD,7.1x4mm-20℃~+70℃ 10,000 Cycles 1A 4.15mm 4mm 6V 7.1mm Black DPDT Gull Wing Rectangular Columnar Surface Mount,Vertical SMD,7.1x4mm Slide Switches ROHSG-SwitchSlide Switches
README
README.mdPCB for PicoTracker
All data in order to fabricate the PCB for the picoTracker
Buy the official kit at xiphonics store
Trademark Notice
This repository contains the open-source hardware design files for the picoTracker project.
The hardware design files are released under the CC0 1.0 Universal license and may be used, modified, manufactured, and sold without restriction.
However, the picoTracker name, logos, product branding, and associated trademarks are not covered by the CC0 license and are not licensed for use by third parties.
You may manufacture and sell hardware derived from these design files, but you may not market, advertise, label, or otherwise represent such products using the "picoTracker" name or branding without prior written permission from Xiphonics.
Products manufactured from these files must be sold under a different product name and must not imply endorsement by, affiliation with, or origin from Xiphonics.
To facilitate this separation, the manufacturing files distributed through this repository intentionally omit picoTracker branding elements.
Use of the picoTracker name in connection with unauthorized derivative hardware may constitute trademark infringement and unfair competition.
Parts
98| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 100nF | Capacitor_SMD:C_0603_1608Metric | C4, C14, C15, C16, C17, C18, C19, C20, C21, C25, C26, C28, C30, C38, C45, C46 |
| 8 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C7, C8, C9, C10, C22, C32, C37, C48 |
| 7 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C27, C29, C31, C40 |
| 6 | 1uF | Capacitor_SMD:C_0603_1608Metric | C13, C23, C24, C47, C49, C57 |
| 5 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R8, R13, R16, R27 |
| 5 | 600@100MHz | Resistor_SMD:R_0805_2012Metric | FB1, FB2, FB3, FB4, FB5 |
| 4 | 47uF | Capacitor_SMD:C_0805_2012Metric | C5, C6, C11, C12 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C33, C34 |
| 2 | 20pF | Capacitor_SMD:C_0603_1608Metric | C35, C36 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R10, R11 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric | R14, R15 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | IC1, IC2 |
| 1 | 10 | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | 12MHz 20pF ±10ppm | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 1N4148WS | Diode_SMD:D_SOD-323 | D1 |
| 1 | 220 | Resistor_SMD:R_0402_1005Metric | R22 |
| 1 | 270 | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 33 | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 560 | Resistor_SMD:R_0603_1608Metric | R29 |
| 1 | 82k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | AP2502KTR-G1 | project:SOT23-6_DIO | U1 |
| 1 | BQ24074RGT | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm | U2 |
| 1 | Conn_01x03 | project:CONN_S3B-ZR-SM4A-TFLFSN_JST | J1 |
| 1 | Conn_02x10_Counter_Clockwise | Connector_Hirose:Hirose_DF12_DF12C3.0-20DS-0.5V_2x10_P0.50mm_Vertical | J3 |
| 1 | DNF | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | FPC-05FB-40PH20 | project:FPC_40-flap | J10 |
| 1 | H11L1 | Package_DIP:SMDIP-6_W9.53mm | IC8 |
| 1 | Headphones | project:PJ327C4A | J5 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | MIDI In | project:PJ327C4A | J9 |
| 1 | MIDI Out | project:PJ327C4A | J8 |
| 1 | MS-22D28-G020 | project:MS22D28G020 | SW1 |
| 1 | Micro_SD_Card | project:Xunpu_TF-115_microSD | J4 |
| 1 | PCM5102A | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | IC5 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | IC6 |
| 1 | SW_SPST | project:SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | TPA6139A2RGTR | project:QFN50P300X300X100-17N-D | IC3 |
| 1 | USB_C_Receptacle_USB2.0 | project:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J2 |
| 1 | W25Q128JVS | project:SOIC-8_5.23x5.23mm_P1.27mm | IC4 |
The 97 most common of 98 parts.
More from xiphonics/picoTracker-pcb
1Similar boards
- 4 layers56.6 × 41.6 mm
- 6 layers147 × 90 mm
- 4 layers80 × 70 mm
- 4 layers85.3 × 75.7 mm
- 2 layers46 × 47.5 mm
Pico opm writer pcba
hyano/pico-opm-writer
Raspberry Pi Pico 2 (RP2350) firmware that drives a YM2151 (OPM) register bus over USB serial, with a PIO-generated master clock and Python tools for batch sequences and DAC capture analysis.
68 partsMIT - 4 layers136.3 × 71.1 mm
- 2 layers74.9 × 39.4 mm
ProjectFiles
khnmuhaimin/EEE3088F-Group-64
This repository contains the design and implementation of the sensing and power subsystems for a micromouse project.
28 partsMIT - 2 layers39.5 × 11.4 mm
Jumper switches smd
silasstokes/header_pins_to_switches_adapter
A compact SMD PCB adapter that replaces traditional 2.54mm header pin jumpers with four labeled slide switches. No more fumbling with tiny jumper caps or searching for pliers.
5 parts
Questions
How big is the PicoTracker PCB?
It measures 76 × 63.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the PicoTracker use?
98 parts, built around the RP2040, AP2502KTR-G1, W25Q128JVSIQ and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PicoTracker KiCad files?
From the xiphonics/picoTracker-pcb repository on GitHub, at the commit this page was made from: the board is main/picoTracker.kicad_pcb and its schematic bezel/bezel.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PicoTracker design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).