

Titan 2026 rev a
TITAN Tandem Electronics System for 2026
- Size
- 82 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 87
- Nets
- 138
- Pads
- 439
- Tracks, vias
- 693, 67
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 8 Apr 2026
- Updated
- 19 Sep 2026
Overview
Titan 2026 rev a is an open-source printed circuit board by savob, from the savob/titan_2026 repository on GitHub. It is a 2-layer board of 82 × 56 mm with 87 parts on 138 nets, routed with 693 tracks and 67 vias.
It is built around the STM32F105RCT6, AT2659S and ATGM336H-5N31, with the BME280, INA219AIDCN and TPS2116DRL among its other parts. Its parts include 24 resistors, 22 capacitors, 13 ICs, 12 connectors and 3 diodes. It belongs with the STM32 boards of this library.
Main components
12STM32F105RCT6
LQFP-64(10x10)-40℃~+85℃ 12bit 12bit 256KB 2V~3.6V 32 Bit 51 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AT2659S
SOT-23-6-15dBm -40℃~+85℃ -6dBm 0.8dB 1.4V~3.6V 1.55GHz~1.615GHz 15dB 20dB 20dB 4.4mA 输出匹配集成、快速使能控制、低功耗模式、ESD保护 SOT-23-6 Low Noise Amplifiers (LNA) - RF ROHSZHONGKEWEILow Noise Amplifiers (LNA) - RFATGM336H-5N31
SMD,10.1x9.7mm-148dBm -40℃~+85℃ 2.5m 2.7V~3.6V 25mA@3.3V 35s GPS、BDS UART、I2C SMD,10.1x9.7mm GNSS Modules ROHS杭州中科微GNSS ModulesBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorINA219AIDCN
SOT-23-8-40℃~+125℃ 0.1uV/℃ 100dB 10uV 20uA 300mV~26V 3V~5.5V 700uA Bidirectional detection、Zero drift / auto-zero、Input filter、Power monitoring、Digital output interface ±26V SOT-23-8 Current Sense Amplifiers ROHSTexas InstrumentsCurrent Sense AmplifiersTPS2116DRL
SOT-583Operating status indication SOT-583 Power Management - Specialized ROHSTexas InstrumentsPower Distribution SwitchesSCD41-D-R2
LGA-20UncategorisedSensirionTLV73333PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 125mV@(300mA) 28uVrms 3.3V 300mA 34uA 5.5V 50dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPS563201
UncategorisedTexas InstrumentsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)BWSMA-KWE-Z001
插件1 50Ω 6.2mm Bent tip Board Side Inner hole SMA 插件 Coaxial Connectors (RF) ROHSBAT WIRELESSCoaxial Connectors (RF)DS1023-2*20SF11
插件,P=2.54mm-40℃~+105℃ 2 2.54mm 2.54mm 2x20P 3A 40P 600V 8.5mm Gold Through Hole Top 插件,P=2.54mm Female Headers ROHSCONNFLYFemale Headers
README
hardware/wheel_2026_rev_a/README.mdTITAN Wheel 2026 Rev. A
This board houses a brake temperature sensor as well as a wheel encoder for monitoring speed and distance. It was designed to fit within the wheel bracket close to the brake disk without interfering with the rider's pedaling.
Changes from 2022
The main changes from the last version will be in improving physical reliability of the system
- Changed everything to other than sensors to be surface mount on the top of the PCB to eliminate the possibility of shorting against mounting surface
- Changed operational amplifier to a TLV2372IDR instead of an LM358 for better performance, namely rail-to-rail output
- Using pads to connect the data cables, headers can be soldered in later if desired
- Removed connector to daisy-chain wheels since that is now handled on the HAT
- Added notes to operate at 3.3 V not 5 V - although the system can handle it
Looking on data from 2022, there was some noise on the encoder speed signal when plotted alongside the GPS derived speed. This could potentially benefit from filtering the signals, although I would really chalk it up to my firmware not properly capturing each spoke and not using a hardware timer.
Tuning the Encoder's Comparator Operation
The onboard comparator circuit for the wheel encoder needs to have the two potentiometers to be properly set for reliable operation. One is responsible for the baseline threshold the encoder is compared to to know if the spoke is present of not, labeled THRES. The other potentiometer adjusts the level of hysteresis preventing spurious switching by moving the active threshold so the signal can't repeatedly cross it, labeled HYST.
To begin, the board must be installed into the wheel bracket and powered, ideally via the TITAN HAT. An oscilloscope is strongly recommended to probe the test pads while doing this to complete it accurately but, but not necessary. If possible, perform this with the wheel enclosed in its fairing - or out at least out of direct sunlight as it may influence the IR sensor.
Without an Oscilloscope
- Connect the target wheel board to an RPi HAT board and supply power to the HAT board to power the sensor board - battery or USB power is fine.
- Gently turn both potentiometers entirely counterclockwise to reset them.
- Rotate the wheel so that the IR sensor is entirely clear of any brake disk spokes.
- Check that the LED is lit up, if not there may be an issue with the board or too much ambient IR which will need different conditions for testing.
- Rotate the wheel so a spoke is directly in front of the IR sensor.
- Turn
THRESclockwise to increase it until the LED turns off, remember this as the "low" mark. - Spin the wheel and make sure that the LED is turning off with each passing of a spoke, and then back on again. Gradually increase
THRESby turning it clockwise until the LED is no longer turning on again when the spoke is gone - this is the "high" mark. - Set
THRESto be halfway between the "low" and "high" mark. Spinning the wheel should have the LED flash again with each spoke pass. - Keep spinning the wheel and increasing
HYSTby turning it clockwise. - Once the LED is no longer changing state with the wheel's rotation, this it the "high" mark.
- Set
HYSTto be about halfway from the starting/zero point to the "high" mark. - Spin the wheel to ensure that the LED is flashing again.
This should roughly center the threshold correctly and provide a decent level of hysteresis. It is impossible for the human eye to perceive the true effect of hysteresis with the LED alone, so we're basically just guessing this.
With an Oscilloscope
The precise way to do this, no major guesstimations here!
- Connect the target wheel board to an RPi HAT board and supply power to the HAT board to power the sensor board - battery or USB power is fine.
- Gently turn both potentiometers entirely counterclockwise to "reset" them.
- Rotate the wheel so that the IR sensor is entirely clear of any brake disk spokes.
- Check that the LED is lit up, if not there may be an issue with the board or too much ambient IR which will need different conditions for testing.
- Read the voltage on the test point labeled
RAW, this is our ambient level. - Rotate the wheel so that there is a spoke directly in front of the IR sensor.
- Record the voltage on the test point labeled
RAW, this is our presence level. - Gradually turn
THRESpotentiometer until the voltage on the test point labeledTHRis halfway between the ambient and presence levels. If the spoke is still in front of the IR sensor at this point, the LED should turn off. - Spin the wheel to observe the LED turning on and off as the spoke passes.
- Keep the wheel spinning and probe
OUT. - Gradually increase
HYSTby turning the potentiometer clockwise until the signal onOUTshows a single pulse for each spoke pass rather than a series of pulses during the transition. Then turnHYSTa sliver more - just not too much so that theOUTstops switching- If you're also able to probe the other two signals you should be able to see that
THRis changing between two levels and thatRAWshould be able to crossTHRonly once per spoke passing. RAWshould continue to a level pastTHRafter crossing it, so that even ifTHRdidn't moveRAWwould not be causing potential switching with any sensor noise.- If the hysteresis gets too large then it might make it hard to catch occasional pulses leading to slower perceived speed.
- If you're also able to probe the other two signals you should be able to see that
- Spin the wheel to ensure that the LED is flashing with each spoke passing.
Known IR Encoder Issue
There is a fundamental issue with the use of the IR sensor for the wheel encoder: the wheel encoder would fail to track the wheel speed once the brakes were engaged as it gets saturated due to IR radiation from the brake disks reaching temperatures in the multi-hundred degrees as they stop TITAN at the end of runs.
This issue was tolerable as we still had the GPS speed to fallback to, and the brakes would only be engaged when a run was ending so there was no longer a need to know TITAN's exact speed. Future revisions should consider a different sensor type for the encoder, but this revision kept it since it was field proven and doesn't require modifications to TITAN's wheels.
A possible hack that could be done using these boards as-is, would be to replace the IR sensor with a visible light discrete LED and photodiode or photoreceptor pair. This should avoid the issue where the brake disk temperature affects the sensor while retaining compatability with the wheels as they are.
A larger overhaul of the board could move to using a magnetic system by attaching magnets to the spokes. If wheel modification is to be avoided, then inductive or capacitive proximity sensing system for the spokes could be considered but the rework needed there would be significant and need collaboration with the mechanical team.
Parts
87| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8, C9, C11, C13, C18, C20, C21, C22, C23 |
| 10 | 2k | Resistor_SMD:R_0402_1005Metric | R6, R7, R8, R9, R15, R16, R17, R21, R23, R24 |
| 5 | 120 | Resistor_SMD:R_0402_1005Metric | R1, R2, R4, R12, R14 |
| 5 | 5k1 | Resistor_SMD:R_0402_1005Metric | R5, R10, R11, R19, R20 |
| 4 | MountingHole_2.7mm_M2.5_ISO14580_Pad_TopBottom | MountingHole:MountingHole_2.7mm_M2.5_ISO14580_Pad_TopBottom | MH1, MH3, MH4, MH4 |
| 3 | 10u | Capacitor_SMD:C_0603_1608Metric | C12, C16, C17 |
| 3 | 28k | Resistor_SMD:R_0402_1005Metric | R3, R18, R22 |
| 3 | SolderJumper_3_Open | Jumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm | JP1, JP2, JP5 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric | C14, C15 |
| 2 | B3B-XH | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4, J5 |
| 2 | B5B-XH | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J2, J3 |
| 2 | B7B-XH | Connector_JST:JST_XH_B7B-XH-A_1x07_P2.50mm_Vertical | J7, J8 |
| 2 | TPS2116DRL | Package_TO_SOT_SMD:SOT-583-8 | U9, U10 |
| 2 | WHITE | LED_SMD:LED_0805_2012Metric | D2, D3 |
| 1 | 10m | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | 3u3 | Inductor_SMD:L_Changjiang_FNR6045S | L1 |
| 1 | 470p | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 6n8 | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 8M | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | AT2659S | Package_TO_SOT_SMD:SOT-23-6 | U13 |
| 1 | ATGM336H-5N31 | titan:ATGM336H-5N | U11 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U1 |
| 1 | BWSMA-KWE-Z001 | Connector_Coaxial:SMA_BAT_Wireless_BWSMA-KWE-Z001 | J12 |
| 1 | DS1023-2*20SF11 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | HB-PH9-12727PB2GOB | Connector_PinHeader_1.27mm:PinHeader_2x07_P1.27mm_Vertical_SMD | J6 |
| 1 | INA219AIDCN | Package_TO_SOT_SMD:SOT-23-8 | U6 |
| 1 | ISO1642DWR | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U4 |
| 1 | NRF24L01_Breakout | titan:nRF24L01_PA_LNA_Breakout | U12 |
| 1 | RED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | SCD41-D-R2 | Sensor:Sensirion_SCD4x-1EP_10.1x10.1mm_P1.25mm_EP4.8x4.8mm | U2 |
| 1 | STM32F105RCT6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U3 |
| 1 | SW_SPST | titan:SW_SPST_SKPM | SW1 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP4 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm_NumberLabels | JP3 |
| 1 | TLV73333PDBV | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | TPS563201 | Package_TO_SOT_SMD:SOT-23-6 | U8 |
| 1 | USB4105-GF-A-120 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J9 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | XT30PW-F20.G.Y | Connector_AMASS:AMASS_XT30PW-F_1x02_P2.50mm_Horizontal | J10 |
| 1 | XT30PW-M30.G.Y | Connector_AMASS:AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J11 |
More from savob/titan_2026
1- 2 layers48 × 20 mm

Similar boards
- 4 layers78 × 48 mm

Motherboard rev 3
hpvdt/falcon_motherboard
Firmware and hardware designs for the Falcon motherboard
69 parts - 4 layers20.5 × 23 mm

Ublox breakout
TobleMiner/ublox-M8030-KT-breakout
Breakout for the bare UBX-M8030-KT chip. Supports pin compatible chips from M6, M7 and M8 generations. JLCSMT assembly supported
32 parts1 - 2 layers100 × 80 mm

- 2 layers71.5 × 63.8 mm

MiniUSBFF
Board-Folk/flash-floppy-drives
Multiple hardware projects that use the Flash Floppy firmware by Kier Fraser for various systems
58 parts3 - 4 layers99.8 × 74.9 mm

- 4 layers60 × 70 mm

Control board PCB
arthur-wirjo/reaction-wheel-inverted-pendulum
A custom-engineered Reaction Wheel Inverted Pendulum designed as a physical testbed for advanced modern control theory.
77 partsMIT - 4 layers80 × 156 mm

Supercap simple
Twisted-Fields/acorn-robot-electronics
PCB hardware designs in KICAD for Acorn, the precision farming rover from Twisted Fields.
56 parts81 - 2 layers49 × 18 mm

Questions
How big is the Titan 2026 rev a PCB?
It measures 82 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Titan 2026 rev a use?
87 parts, built around the STM32F105RCT6, AT2659S, ATGM336H-5N31 and BME280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Titan 2026 rev a KiCad files?
From the savob/titan_2026 repository on GitHub, at the commit this page was made from: the board is hardware/titan_2026_rev_a/titan_2026_rev_a.kicad_pcb and its schematic hardware/titan_2026_rev_a/interboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Titan 2026 rev a design in my own project?
Its repository states no licence, so its author keeps all rights: ask savob before reusing the design.