

Load v2
- Size
- 150.5 × 90.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 118
- Nets
- 86
- Pads
- 320
- Tracks, vias
- 721, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 28 Nov 2016
- Updated
- 23 Jun 2017
Overview
Load v2 is an open-source printed circuit board by sangseu, from the sangseu/kicad repository on GitHub. It is a 2-layer board of 150.5 × 90.8 mm with 118 parts on 86 nets, routed with 721 tracks and 0 vias.
It is built around the ATMEGA328-PU, LM324N and ICL7660N, with the LM7812CT, LM7805CT and TL431 among its other parts. Its parts include 57 resistors, 21 capacitors, 11 diodes, 10 connectors and 8 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM324N
DIP-14-16V~-1.5V、1.5V~16V -40℃~+85℃ 1.5V~30V 250nA 35mA 4 50nA 600uA 7uV/℃ 80dB 9mV DIP-14 Operational Amplifier ROHSHGSEMIOperational AmplifierICL7660N
DIP-83V~9.5V DIP-8 Charge Pumps ROHSHGSEMIDC-DC ConvertersLM7812CT
TO-220-30℃~+125℃@(Ta) 1 1.5A 12V 35V 55dB@(120Hz) 75uV Fixed Positive Short Circuit Protection、Thermal shutdown TO-220-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHGSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM7805CT
TO-2200℃~+70℃@(Ta) 1 1A 20V 2V@(1A) 40uV 5V 62dB@(120Hz) 8mA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTL431
SOT-23-20℃~+85℃ 150mA 1mA 2.5V~36V 50ppm/℃ Adjustable Parallel Temperature compensation control ±1% SOT-23 Voltage Reference ROHSGuangdong HottechVoltage Reference14D470K
插件,P=7.5mm100mW 15J 1kA 30V 38V 43V~53V 6.5nF@1kHz 93V 插件,P=7.5mm Varistors ROHSRUILONVaristors
Parts
118| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 0R | Wire_Connections_Bridges:WireConnection_0.80mmDrill | R47, R48, R49, R50, R51, R52, R53, R54, R55, R56, R57 |
| 11 | 10k | Resistors_THT:Resistor_Horizontal_RM7mm | R8, R20, R21, R26, R32, R34, R35, R38, R41, R45, R46 |
| 10 | 0.5R | Resistors_SMD:R_2512_HandSoldering | R9, R10, R11, R12, R13, R14, R15, R16, R17, R18 |
| 8 | 100nF | Capacitors_THT:C_Disc_D3_P2.5 | C3, C5, C16, C17, C20, C21, C22, C23 |
| 7 | 1k | Resistors_THT:Resistor_Horizontal_RM7mm | R1, R4, R23, R27, R39, R42, R43 |
| 6 | 470R | Resistors_THT:Resistor_Horizontal_RM7mm | R5, R6, R19, R22, R40, R44 |
| 4 | 330R | Resistors_THT:Resistor_Horizontal_RM7mm | R24, R28, R31, R36 |
| 4 | 5.1V | Diodes_THT:Diode_DO-35_SOD27_Horizontal_RM10 | D8, D9, D10, D11 |
| 4 | Led_Small | LEDs:LED-3MM | D2, D3, D4, D6 |
| 3 | Q_NPN_BCE | TO_SOT_Packages_THT:TO-92_Molded_Narrow | Q1, Q2, Q3 |
| 2 | 100nF | Capacitors_SMD:C_0805_HandSoldering | C9, C10 |
| 2 | 10k | Resistors_SMD:R_0805_HandSoldering | R2, R3 |
| 2 | 10uF-25V | Capacitors_THT:C_Radial_D5_L6_P2.5 | C6, C7 |
| 2 | 14D470K | Varistors:RV_Disc_D15.5_W3.9_P7.5 | VR1, VR2 |
| 2 | 220F-25V | Capacitors_THT:C_Radial_D5_L6_P2.5 | C2, C15 |
| 2 | 22pF | Capacitors_SMD:C_0805_HandSoldering | C12, C13 |
| 2 | 8.2k | Resistors_THT:Resistor_Horizontal_RM7mm | R25, R37 |
| 2 | HEATSINK | Heatsinks:Heatsink_Stonecold_HS-132_32x14mm_2xFixation1.5mm | HS1, HS2 |
| 2 | LM324N | Housings_DIP:DIP-14_W7.62mm_LongPads | U5, U6 |
| 2 | LM7812CT | Power_Integrations:TO-220 | U1, U7 |
| 1 | 100nF | Capacitors_THT:C_Rect_L7_W2_P5 | C18 |
| 1 | 100nF | Capacitors_THT:C_Rect_L7_W2.5_P5 | C11 |
| 1 | 10k | Potentiometers:Potentiometer_Bourns_3296W_3-8Zoll_Inline_ScrewUp | RV1 |
| 1 | 10k | Resistors_THT:Resistor_Horizontal_RM15mm | R29 |
| 1 | 10uH | Resistors_THT:Resistor_Horizontal_RM7mm | R7 |
| 1 | 12N60C | Connectors_Phoenix:PhoenixContact_MCV-G_05x5.08mm_Vertical | P4 |
| 1 | 12VAC | Connectors_Phoenix:PhoenixContact_MCV-G_02x5.08mm_Vertical | P1 |
| 1 | 16MHz | Crystals:Crystal_HC52-U_Vertical | Y1 |
| 1 | 180k | Resistors_THT:Resistor_Horizontal_RM7mm | R33 |
| 1 | 180k | Resistors_THT:Resistor_Horizontal_RM15mm | R30 |
| 1 | 1N4001 | Diodes_THT:Diode_DO-35_SOD27_Horizontal_RM10 | D7 |
| 1 | 1N5402 | Diodes_THT:Diode_DO-201AD_Horizontal_RM15 | D5 |
| 1 | 20k | Potentiometers:Potentiometer_Bourns_3296W_3-8Zoll_Inline_ScrewUp | RV2 |
| 1 | 220uF-50V | Capacitors_THT:C_Radial_D5_L6_P2.5 | C1 |
| 1 | 22nF | Capacitors_THT:C_Disc_D3_P2.5 | C19 |
| 1 | 470uF-25V | Capacitors_THT:C_Radial_D5_L6_P2.5 | C4 |
| 1 | 7-seg | Connectors:XH2.54-4P | P9 |
| 1 | ATMEGA328-P | Housings_DIP:DIP-28_W7.62mm_LongPads | IC1 |
| 1 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02 | P5 |
| 1 | Diode_Bridge | Diodes_THT:Diode_Bridge_18.5x5.5 | D1 |
| 1 | FAN | Connectors:XH2.54-2P | P8 |
| 1 | ICL7660 | Power_Integrations:PDIP-8 | U3 |
| 1 | LM7805CT | Power_Integrations:TO-220 | U2 |
| 1 | NGUON | Connectors_Phoenix:PhoenixContact_MCV-G_02x5.08mm_Vertical | P2 |
| 1 | SAC | Connectors_Phoenix:PhoenixContact_MCV-G_02x5.08mm_Vertical | P3 |
| 1 | TL431 | TO_SOT_Packages_THT:TO-92_Molded_Narrow | U4 |
| 1 | UART | Pin_Headers:Pin_Header_Straight_1x04 | P7 |
| 1 | button | Connectors:XH2.54-8P | P6 |
| 1 | relay | Connectors:XH2.54-4P | P10 |
| 1 | reset | Buttons_Switches_THT:SW_PUSH_6mm | SW1 |
More from sangseu/kicad
10- 2 layers

- 2 layers

- 2 layers213.1 × 165.9 mm

- 2 layers206.1 × 150.5 mm

- 2 layers152.4 × 86.4 mm

- 2 layers140 × 70 mm

- 2 layers224.2 × 130.8 mm

- 2 layers

- 2 layers142.2 × 17.8 mm

- 2 layers

Similar boards
- 2 layers73 × 35.6 mm

Twilight switch
joseguerra3000/twilight-switch
System able to control a relee to turn on or off exterior lights depending on the lighting.
24 parts1 - 2 layers117.6 × 97.8 mm

Alimentatore
CarloMara/didactic-octo-PSU
So, @nicogela and I decided to build a LAB PSU, but because we're lazy people and we don't like to carry weight we're tring to unite the high efficiency of the switching topologies to the high stability and low noise of…
83 parts - 2 layers137.2 × 78.7 mm

- 2 layers49.5 × 49.5 mm

- 2 layers263.3 × 150.4 mm

ArduBooster 4x2
ddo02/ArduBooster
Throttle pedal booster based on Arduino. To improve throttle response.
216 parts3 - 2 layers169.3 × 128 mm

PSU PCB
ThomasVDD/SmartSupply
SmartSupply is a digital battery powered lab powersupply. It is Arduino compatible and can be controlled via PC over USB.
134 parts96 - 2 layers69.9 × 52.6 mm

ArduiBodet
PatriceG/ArduiBodet
Horloge mère pour Horloge de type Bodet pilotée par Arduino
22 parts5GPL-3.0 - 2 layers100.1 × 70.1 mm

Questions
How big is the Load v2 PCB?
It measures 150.5 × 90.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Load v2 use?
118 parts, built around the ATMEGA328-PU, LM324N, ICL7660N and LM7812CT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Load v2 KiCad files?
From the sangseu/kicad repository on GitHub, at the commit this page was made from: the board is project/load_v2/v2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Load v2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask sangseu before reusing the design.