
NucDeck Left Controller PCB
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!

Shield for the Spartan Edge board to output HDMI for the Game Boy Advance
GBAHD Shield is an open-source printed circuit board by sanchezand, from the sanchezand/GBAHD-Shield repository on GitHub. It is a 2-layer board of 79.5 × 64.4 mm with 70 parts on 147 nets, routed with 752 tracks and 115 vias.
It is built around the ATMEGA328P-AU. Its parts include 13 connectors, 4 switches, 3 capacitors, 2 resistors and 1 IC. It belongs with the retro computing and games boards and the AVR (ATmega, ATtiny) boards of this library.
This is a shield for the gbaHD project.
Has the following features.
If you wish to contribute, see something wrong or want to add a feature please make a pull request or leave an issue!
| Reference | Value |
|---|---|
| C1, C2 | 22pF |
| C3 | 100nF |
| R1 | 10K ohm |
| R2 | 120 ohm (or change for your LED) |
| D1 | 5mm LED or TJ-L5FPTGCRMFCSFLC2R-A5 |
| U2 | ATMEGA328p-AU |
| X1 | 16MHz Crystal SMD-3225 |
| SW1 | XKB-TS-1185EC-C-D-B |
| SW2 | XKB_XKB5858-Z-C |
| J1 | JUSHUO_AFC01-S40FCC-00 |
| J2 | PinHeader 2x08 2.54mm |
| J3, J9 | JUSHUO_AFC01-S20FCC-00 |
| J5 | JUSHUO_AFC07-S34FCC-00 |
| J7 | JUSHUO_AFC01-S32FCC-00 |
| J4 | PinHeader 2x10 2.54mm |
| P1, P2 | Wii Expansion Port |
| EXTRA 1 | PinHeader 1x08 2.54mm |
| EXTRA 2 | PinHeader 1x06 2.54mm |
In order to program the MCU, you need an arduino to use as ISP.
Use the following image to wire up an arduino to the board to program it.
I would also recomend not programming it while seated in the FPGA board.

After wiring the board, follow this tutorial to flash the bootloader and the sketch to the board.
ICSP Tutorial
The Arduino code requires the NintendoExtensionCtrl library.

This documentation describes Open Hardware and is licensed under the CERN OHL v. 1.2. You may redistribute and modify this documentation under the terms of the CERN OHL v.1.2. (http://ohwr.org/cernohl). This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN OHL v.1.2 for applicable conditions.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | VAL** | Panelization:mouse-bite-2.54mm-slot | mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite, mousebite |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | CONN_WII | Raizu_OFFSET:CONN_WII | P1, P2 |
| 2 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J8, J11 |
| 2 | Conn_01x20 | Raizu:JUSHUO_AFC01-S20FCC-00 | J3, J9 |
| 2 | VAL** | keyboard_parts:HOLE_M3 | HOLEM3, HOLEM3 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 120 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | ATmega328P-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U2 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | Conn_01x32 | Raizu:JUSHUO_AFC01-S32FCC-00 | J7 |
| 1 | Conn_01x34 | Raizu:JUSHUO_AFC07-S34FCC-00 | J5 |
| 1 | Conn_01x40 | Raizu:JUSHUO_AFC01-S40FCC-00 | J1 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J6 |
| 1 | Conn_02x08_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J2 |
| 1 | Conn_02x10_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J4 |
| 1 | Crystal_GND2 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | X1 |
| 1 | EX1 | TestPoint:TestPoint_Pad_1.5x1.5mm | EX1 |
| 1 | EX2 | TestPoint:TestPoint_Pad_1.5x1.5mm | EX2 |
| 1 | EX3 | TestPoint:TestPoint_Pad_1.5x1.5mm | EX3 |
| 1 | EX4 | TestPoint:TestPoint_Pad_1.5x1.5mm | EX4 |
| 1 | GBA_A | Raizu_OFFSET:SOLDER_PAD | TP0 |
| 1 | GBA_B | Raizu_OFFSET:SOLDER_PAD | TP1 |
| 1 | GBA_CLK | Raizu_OFFSET:SOLDER_PAD | GBA3 |
| 1 | GBA_DD | Raizu_OFFSET:SOLDER_PAD | TP7 |
| 1 | GBA_DL | Raizu_OFFSET:SOLDER_PAD | TP5 |
| 1 | GBA_DR | Raizu_OFFSET:SOLDER_PAD | TP4 |
| 1 | GBA_DU | Raizu_OFFSET:SOLDER_PAD | TP6 |
| 1 | GBA_EX1 | Raizu_OFFSET:SOLDER_PAD | GEX1 |
| 1 | GBA_EX2 | Raizu_OFFSET:SOLDER_PAD | GEX2 |
| 1 | GBA_EX3 | Raizu_OFFSET:SOLDER_PAD | GEX3 |
| 1 | GBA_EX4 | Raizu_OFFSET:SOLDER_PAD | GEX4 |
| 1 | GBA_GND | Raizu_OFFSET:SOLDER_PAD | GBA4 |
| 1 | GBA_L | Raizu_OFFSET:SOLDER_PAD | TP9 |
| 1 | GBA_R | Raizu_OFFSET:SOLDER_PAD | TP8 |
| 1 | GBA_RESET | Raizu_OFFSET:SOLDER_PAD | GBA2 |
| 1 | GBA_S01 | Raizu_OFFSET:SOLDER_PAD | S1 |
| 1 | GBA_S02 | Raizu_OFFSET:SOLDER_PAD | S2 |
| 1 | GBA_SEL | Raizu_OFFSET:SOLDER_PAD | TP2 |
| 1 | GBA_STR | Raizu_OFFSET:SOLDER_PAD | TP3 |
| 1 | GBA_VCC | Raizu_OFFSET:SOLDER_PAD | GBA1 |
| 1 | LED | LED_THT:LED_D5.0mm_FlatTop | D1 |
| 1 | LOGO | Raizu_OFFSET:OFFSET_LOGO_4.0mm | G*** |
| 1 | PinHeader_1x06_P2.54mm_Vertical | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | EXP2 |
| 1 | PinHeader_1x08_P2.54mm_Vertical | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | EXP1 |
| 1 | SW_Push | Raizu_OFFSET:XKB-TS-1185EC-C-D-B | SW1 |
| 1 | Switch-DPDT | Raizu_OFFSET:XKB_XKB5858-Z-C | SW2 |
| 1 | TestPoint | Raizu_OFFSET:SOLDER_PAD | TP19 |
The 68 most common of 70 parts.

dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!


profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance

futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.


sportiduino/sportiduino
Electronic timing system for orienteering and similar outdoor sports events on Arduino

SukkoPera/OpenPSX2AmigaPadAdapter
Playstation to Commodore Amiga/CD32 Controller Adapter

4x1md/vx8_gps
DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.
It measures 79.5 × 64.4 mm and has 2 copper layers, 1.6 mm thick.
70 parts, built around the ATMEGA328P-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the sanchezand/GBAHD-Shield repository on GitHub, at the commit this page was made from: the board is shield/GBAHD_Shield.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask sanchezand before reusing the design.