
Vik universal
sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.
Vikropad is an open-source printed circuit board by sadekbaroudi, from the sadekbaroudi/vik repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 2-layer board of 94 × 94.5 mm with 59 parts on 59 nets, routed with 1,025 tracks and 178 vias.
It is built around the SN74HC595D and 1N4148W. Its parts include 28 diodes, 18 switches, 5 connectors, 4 ICs and 2 resistors.
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.
This was used to demonstrate a build for vulpes minora. See the repo for pictures.
For PCB fabrication, you can use the files in the production folder.
Using the 3 files above, this has been tested at jlcpcb.com
| Category | Classification | Response |
|---|---|---|
| FPC connector | Required | :heavy_check_mark: |
| Breakout pins | Recommended | :x: |
| Uses: SPI | Optional | :heavy_check_mark: |
| SPI used for SPI only | Strongly recommended | :heavy_check_mark: |
| Uses: I2C | Optional | :x: |
| I2C used for I2C only | Strongly Recommended | N/A |
| I2C pull ups | Required | N/A |
| Uses: RGB | Optional | :heavy_check_mark: |
| Uses: Extra GPIO 1 | Optional | :heavy_check_mark: |
| Uses: Extra GPIO 2 | Optional | :heavy_check_mark: |
| Standard PCB Size/Mount | Strongly recommended | Large |


| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 1N4148W | Diode_SMD:D_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D10, D11, D12, D13, D14, D15, D16, D17, D18 +2 |
| 18 | SW_Push | fingerpunch:gateron-ks27-choc-v1-mx-soldered-and-hotswap | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18 +2 |
| 10 | 1N4148 | Diode_SMD:D_SOD-123 | D21, D22, D23, D24, D25, D26, D27, D28, D29, D30 |
| 3 | Conn_01x02_Socket | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3, J4, J5 |
| 2 | 4.7kΩ | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9 |
| 2 | 5Way-Tactile_K1-1506DN-01 | fingerpunch:5Way-Tactile_K1-1506DN-01 | HAT1, HAT2 |
| 2 | SN74HC595 | Package_DIP:DIP-16_W7.62mm | U3, U4 |
| 2 | SN74HC595 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1, U2 |
| 1 | Conn_01x01_Socket | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J2 |
| 1 | ~ | vik:vik-module-connector-horizontal | J1 |

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.





Alberta2514640/EIT-Machine
Arbitrary Waveform Generator for the Raspberry Pi Pico 16 Channels

FRC-1721/AccidentCounter
A digital sign hung in the build space advertising days without incident

richgumy/black_sensor
A sensor developed using solely a carbon black silicone elastomer composite and the driving electronics.

It measures 94 × 94.5 mm and has 2 copper layers, 1.6 mm thick.
59 parts, built around the SN74HC595D and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the sadekbaroudi/vik repository on GitHub, at the commit this page was made from: the board is pcb/vikropad/vikropad.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).