2 layers120 × 60 mm
CAN interface
rkhvrnen/UDS-logger
A Python script and MCU source code for collecting real-time diagnostic data from control units of a vehicle using UDS over CAN bus.
82 partsMIT
2 layers43.2 × 17.8 mm
NanoV3.3
s-a-usman/Type-C-Arduino-NanoArduino Nano Clone with USB type-c
- Size
- 43.2 × 17.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 53
- Pads
- 180
- Tracks, vias
- 422, 41
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 6 (file 20220308)
- Created
- 20 Dec 2023
- Updated
- 13 Jan 2024
Overview
NanoV3.3 is an open-source printed circuit board by s-a-usman, from the s-a-usman/Type-C-Arduino-Nano repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 43.2 × 17.8 mm with 35 parts on 53 nets, routed with 422 tracks and 41 vias.
It is built around the FT232RL, LM1117IMPX-5.0 and MF-FSMF050X-2. Its parts include 9 capacitors, 4 connectors, 3 ICs, 2 fuses and 1 diode.
Main components
3
FT232RL
SSOP-28-208mil-40℃~+85℃ 3.3V~5.25V、4V~5.25V USB 2.0 USB to UART SSOP-28-208mil USB Converters ROHSFTDIUSB Converters
LM1117IMPX-5.0
SOT-223-4-40℃~+125℃@(Tj) 1 1.2V@(800mA) 150uVrms 15V 5V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MF-FSMF050X-2
0603-40℃~+85℃ 0.8mm 1.6mm 100mΩ 1A 40A 500mA 500mW 6V 800mΩ 0603 Resettable Fuses ROHSBournsResettable Fuses
README
README.mdArduino-nano-with-type_C
This is an Arduino nano board with type c port instead of the popular type b.
Acknowledgement
The original project was downloaded from (Arduino Official Store)[https://store.arduino.cc/products/arduino-nano].
3D models in the NanoV3.3.3dshapes directory are works of others.
| File | Source |
|---|---|
| DO-220AA.stp | https://componentsearchengine.com/part-view/SS1P3L-M3%2F84A/Vishay |
| SW_SPST_3.9x2.9mm.wrl | https://lceda.cn |
| Others | https://gitlab.com/kicad/libraries/kicad-packages3D |
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nF | NanoV3.3:C_0603_1608Metric | C1, C4, C6, C9 |
| 4 | DNP | NanoV3.3:Fiducial_1mm_Mask1.5mm | FD1, FD2, FD3, FD4 |
| 3 | 1uF | NanoV3.3:C_0603_1608Metric | C3, C7, C8 |
| 2 | 1K | NanoV3.3:R_CAY16-4 | RP1, RP2 |
| 2 | 4,7uF_16V | NanoV3.3:CP_EIA-3216-18_Kemet-A | C2, C5 |
| 2 | Conn_1x15 | NanoV3.3:PinHeader_1x15_P2.54mm_Vertical | J1, J2 |
| 2 | DNP | NanoV3.3:TestPoint_Pad_D1.0mm | D-0, D+0 |
| 2 | Green | NanoV3.3:LED_0805_2012Metric | PWR0, TX0 |
| 2 | MFFSMF050 | NanoV3.3:Fuse_0603_1608Metric | F1, F1 |
| 1 | 16MHz | NanoV3.3:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | 328P-MUR | NanoV3.3:VQFN-32-1EP_5x5mm_P0.5mm_EP3.254x3.254mm | IC3 |
| 1 | Conn_2x3 | NanoV3.3:PinHeader_2x3_P2.54mm_Vertical | J4 |
| 1 | FT232RL | NanoV3.3:SSOP-28_5.3x10.2mm_P0.65mm | IC1 |
| 1 | LM1117IMPX-5.0 | NanoV3.3:SOT-223 | IC2 |
| 1 | RESET | NanoV3.3:SW_SPST_3.9x2.9mm | SW1 |
| 1 | Red | NanoV3.3:LED_0805_2012Metric | RX0 |
| 1 | SS1P3L | NanoV3.3:DO-220AA | D1 |
| 1 | Silkscreen_Back | NanoV3.3:Silkscreen_Front | Silkscreen_Front |
| 1 | Silkscreen_Front | NanoV3.3:Silkscreen_Back | Silkscreen_Back |
| 1 | USB_2 | Connector_USB:USB_C_Receptacle_GCT_USB4085 | J3 |
| 1 | Yellow | NanoV3.3:LED_0805_2012Metric | L0 |
Similar boards
- 2 layers43.2 × 17.8 mm
Arduino nano v3 3
javachaos/arduino_simulator
arduinosimulator is a standalone AVR simulation and board-tooling workspace.
37 partsGPL-3.0 - 2 layers62 × 100 mm
- 4 layers48 × 37.5 mm
- 2 layers29 × 12 mm
Ubmp v1
korken89/micro-bmp
A small Black Magic Probe based on the pinout of the STLink V2 support firmware
25 parts37 - 2 layers79.9 × 41.4 mm
GR ESP32-A1S
GadgetReboot/ESP32-A1S
Breakout PCB for the ESP32-A1S module including an audio amp and basic GPIO headers, USB interface
65 parts27 - 2 layers61.5 × 25 mm
- 2 layers50.7 × 27.9 mm
Questions
How big is the NanoV3.3 PCB?
It measures 43.2 × 17.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the NanoV3.3 use?
35 parts, built around the FT232RL, LM1117IMPX-5.0 and MF-FSMF050X-2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the NanoV3.3 KiCad files?
From the s-a-usman/Type-C-Arduino-Nano repository on GitHub, at the commit this page was made from: the board is NanoV3.3.kicad_pcb and its schematic NanoV3.3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the NanoV3.3 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).