

ArmJ2
- Size
- 69.1 × 53 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 74
- Pads
- 251
- Tracks, vias
- 569, 44
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 26 Mar 2024
- Updated
- 3 Nov 2026
Overview
ArmJ2 is an open-source printed circuit board by robotique-udes, from the robotique-udes/PCB repository on GitHub, published under the MIT licence. It is a 4-layer board of 69.1 × 53 mm with 57 parts on 74 nets, routed with 569 tracks and 44 vias.
It is built around the SN65HVD232D, XT60PW-M and XT30PW-F. Its parts include 16 capacitors, 10 resistors, 9 connectors, 8 ICs and 5 diodes. It belongs with the ESP32 boards of this library.
Main components
3README
rover/2024/pdb/README.mdPDB (Power Distribution Board)
PCB servant à gérer la distribution à bas courant et le de data du rover
Image du PCB en 3D
Objectifs:
- Protéger tous les autres boards du Over/Under Voltage pour le 5V, 12V et 24V
- Seulement le 5v et le 24v sont protégé, car les résistance 5% ont trop d'incertitude.
- Injecteur POE(12V custom pinout) pour les cameras branché en Ethernet
- On/Off possible par le MCU
- Diriger le signal des cameras sur les bonnes pins selon la norme Ethernet
- Agir en tant que POE pour les antennes 24V (vrai POE)
- Controller l'alimentation de 2 circuit d'accessoires 12V
- Par 2 connecteurs Ethernet
- Permettre de pouvoir sortir une des 3 tension (5v, 12v, 24v) par un screw terminal
- Alimente la switch ethernet en dessous
- MCU Connecté sur le CAN BUS
- Sélectionner avec les GPIO les cameras qui doivent recevoir du power
Composants principaux:
- ESP32 DEV KIT V1
- TJA1050 (CAN BUS)
- LTC4365 (Over/Under Voltage protaction)
- DMG4822SSD (DIODE pour la switch du LTC4365)
- DELs
- CLP6C-FKB-CKNPRGJBB7A363 (ERROR DEL)
- Boutons
- Horizontal Amphenol 54602 RJ45
- ASSMANN_A-2014 Ethernet connector
- CRJ036-5-TH_2x4 Ethernet connector
- BTS5200 (4 Channel Mosfet)
Fonctionnement:
- Le PDB reçoit 3 tensions régulé en entrée, du 5V, du 12V et du 24V.
- Le 12V sert principalement pour alimenter les caméras qui sont alimentés avec un POE avec un Pinout spécial. Il sert aussi à alimenter 2 circuit d'accessoires potentiels.
- Le 24V sert à alimenter le/les antennes qui sont sur le Rover.
- Le 5V est passé avec les fils de CanBus pour alimenter et communiquer avec les autres PCB du rover
- Le circuit sécurise les trois tensions contre les sur-tensions et le drops de tensions.
- La sortie vers l'ordinateur principal n'est pas utilisé, l'ordinateur est directement branché dans la switch.
PGIO
Outputs
| Name | GPIO |
|---|---|
| CAM_SIGN_0 | D18 |
| CAM_SIGN_1 | D19 |
| CAM_SIGN_2 | D33 |
| CAM_SIGN_3 | D32 |
| PWM_0 | D21 |
| PWM_1 | D22 |
| ACC1_CONTROL | D23 |
| ACC2_CONTROL | D25 |
| LED_R | D14 |
| LED_G | D27 |
| LED_B | D26 |
Communication
| Name | GPIO |
|---|---|
| TXC | D6 |
| RXC | D7 |
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C4, C6, C7, C9, C11, C14 |
| 6 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C10, C12, C13, C15, C16 |
| 6 | 5.1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R4, R5, R6, R11 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottom | H1, H2, H3, H4 |
| 4 | SW-PTS815SJM250SMTRLFS | RoverFootprint:SW-PTS815 SJM250SMTRLFS | SW1, SW2, SW3, SW4 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R7, R8 |
| 3 | B | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3, D5 |
| 2 | Eth-Horiz | RoverFootprint:Ethernet_Horizontal | J3, J4 |
| 2 | SN65HVD232 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6, U7 |
| 1 | 120 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 40V | Diode_SMD:D_SMA | D4 |
| 1 | Conn_01x02 | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J6 |
| 1 | Conn_01x03 | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J8 |
| 1 | Conn_01x03 | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J5 |
| 1 | Conn_01x06 | Connector_JST:JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J9 |
| 1 | ESP32-S3-WROVER | RF_Module:ESP32-S3-WROOM-1U | U2 |
| 1 | FuseHolder | RoverFootprint:FUSE_3568-20 | F1 |
| 1 | G | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | Jumper PWR | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J10 |
| 1 | LDO-LM7805MPX/NOPB | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U8 |
| 1 | LDO-TLV74033PDBVR | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U5 |
| 1 | TVS-SMDB03CE3 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | USB_C_USB4105-GF-A | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | XT30PW-F | RoverFootprint:AMASS_XT30PW-F_1x02_P2.50mm_Horizontal | J2 |
| 1 | XT60PM-F | RoverFootprint:AMASS_XT60PW-F_1x02_P7.20mm_Horizontal | U3 |
| 1 | XT60PW-M | RoverFootprint:AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | U4 |
More from robotique-udes/PCB
12- 4 layers152.8 × 53.5 mm

- 4 layers100 × 80 mm

- 4 layers96.5 × 97.9 mm

- 4 layers100 × 72.5 mm

- 4 layers57.8 × 80 mm

- 4 layers90 × 50 mm

- 4 layers80 × 50 mm

- 4 layers59.5 × 90 mm

- 4 layers38 × 76 mm

- 4 layers79.5 × 36 mm

- 4 layers32.5 × 59.3 mm

- 4 layers50 × 50 mm

Similar boards
- 4 layers13.4 × 4.5 mm

Lre avio daq2
IITB-Rocket-Team-Avionics/Ember
Experimental Flight Computer with potential mitigations of previous issues faced by FLYTE and a testbed for new systems.
172 parts4MIT - 4 layers100 × 100 mm

Smc power
efebasol/StepperMotorController
Rev A — single-motor bench prototype power board. Feeds the driver board (48 V), the stepper motor brake (24 V) and the logic (5 V / 3V3).
104 parts - 4 layers95 × 62 mm

Logging Current Meter
JustCuzRobotics/Just_Cuz_Logging_Current_Meter
A 150 A / 60 V inline power meter and datalogger for RC ESC test benches, a WM150-class meter with live logging, a graphing touchscreen, and thermistor plus ESC-signal channels.
62 parts - 2 layers240 × 120 mm

Quiver PDB 01
Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.
33 parts617CERN-OHL-S-2.0 - 4 layers55.3 × 29 mm

Drone current sensor board
Kelvin-Ziqi-Zhao/drone-current-sensor-board
High current sensor board for battery+capacitor power supply system
66 parts7 - 2 layers45 × 30 mm

TFSBEC01
ThunderFly-aerospace/TFSBEC01
High efficient switching power supply for UAV actuators.
39 parts5GPL-3.0 - 2 layers208 × 198.1 mm

- 2 layers40 × 21.1 mm

Microscope LED
CGrassin/microscope_led_light_circuit
A dimming LED circuit designed for optical microscopes.
20 parts2CC-BY-4.0
Questions
How big is the ArmJ2 PCB?
It measures 69.1 × 53 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ArmJ2 use?
57 parts, built around the SN65HVD232D, XT60PW-M and XT30PW-F. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ArmJ2 KiCad files?
From the robotique-udes/PCB repository on GitHub, at the commit this page was made from: the board is rover/2025/ArmJ2/latest/ArmJ2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ArmJ2 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).