

Rancho RT1000 SCSI Controller
There can be one PAL on the Card (GAL20L8), this is for the floppy part only. BIOS EPROM is a 27C128 Type, but only 8k are used.
- Size
- 135 × 108 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 44
- Nets
- 140
- Pads
- 460
- Tracks, vias
- 1,620, 168
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 23 Apr 2024
- Updated
- 14 May 2024
Overview
Rancho RT1000 SCSI Controller is an open-source printed circuit board by roberto314, from the roberto314/Rancho-RT1000-SCSI-8-Bit repository on GitHub. It is a 2-layer board of 135 × 108 mm with 44 parts on 140 nets, routed with 1,620 tracks and 168 vias.
It is built around the 74LS245SC and 27C128-15. Its parts include 14 crystals, 10 capacitors, 6 ICs, 3 connectors and 2 resistors.
Main components
274LS245SC
-0℃~+70℃ 12ns@5V,45pF 15mA 24mA 4.75V~5.25V 74LS 8 Bidirectional Output enable Schmitt trigger Tri-State - Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers27C128-15
-0℃~+70℃ 128Kbit 4.5V~5.5V Parallel Port (Parallel) - Non-Volatile Memory (ROM)Microchip TechnologyNon-Volatile Memory (ROM)
README
README.mdRancho-RT1000-SCSI-8-Bit
Recreation of a bootable ISA 8-Bit SCSI Card.

There can be one PAL on the Card (GAL20L8), this is for the floppy part only. BIOS EPROM is a 27C128 Type, but only 8k are used.
For now there is no plan to manufacture the board.
| BIOS Ver. | 8088/80C88 | NEC V20 | 286 | 386SX |
|---|---|---|---|---|
| Rancho 8.10 | no boot, no ASPI | no boot, no ASPI | boots+ASPI | boots+ASPI |
| Rancho 8.20 | no boot, no ASPI | no boot, no ASPI | boots+ASPI | boots+ASPI |
| Corel 1.65 | no boot, Corel ASPI | boots+Corel ASPI | boots+ASPI | boots+ASPI |
Comment: On an XT, even with V20 CPU, with Rancho BIOS, a Disk is found but hangs when trying to boot. RTASPI10.SYS says it needs a 286.
The Card seems to be the same as the Corel LS2000, so i tried the Corel BIOS and it works!
Unfortunately the Corel uses a different CHS Conversion, so the Rancho Images won't work.
The ASPI Driver from the Rancho (RTASPI10.SYS) works with the Corel BIOS and vice versa, BUT they need the correct CHS Values!
The ASPI Driver from the Corel (ASPILS_D.SYS) works with a V20 CPU and with an 8088. The ASPIDISK.SYS Driver doesn't like the 8088 BUT the Trantor TSCSI Disk Driver in Version 4.53 works (Filename: TSCSI.453)


The Rancho BIOS doesn't need an Interrupt, the Corel BIOS seems to work only with IRQ4! The Jumper X14, X15, X16, X17 and X18 won't do anything with the Corel BIOS.
With the BIOS EPROM installed the 8088 hangs during boot from Floppy! One has to disable the BIOS in order to boot on an 8088.
The Corel BIOS can only address two Harddisks without an ASPI Driver installed!
Heads and Sectors working with original RT1000 BIOS (v8.20):
Tested with MSDOS 5 and with a 386SX and does NOT work with an 8088 nor 80C88!:
(spc = Sectors/Cluster, spf = Sectors/FAT)
- C: 1023 / H:2 / S:32 32 MB (FAT16/4) spc=4,spf=0x40: works
- C: 1023 / H:4 / S:32 64 MB (FAT16/6) spc=4,spf=0x80: non-system disk
- C: 511 / H:8 / S:32 64 MB (FAT16/6) spc=4,spf=0x80: non-system disk
- C: 1015 / H:3 / S:43 65510 kB (FAT16/6) spc=4,spf=0x80: works
- C: 1023 / H:8 / S:32 128 MB (FAT16/6) spc=4,spf=0x100: non-system disk
- C: 1007 / H:5 / S:52 127.8 MB (FAT16/6) spc=4,spf=0x100: works
- C: 1021 / H:9 / S:57 261800 kB (FAT16/6) spc=8,spf=0x100: works
- C: 1023 / H:9 / S:57 262627 kB (FAT16/6) spc=16,spf=0x100: non-system disk
- C: 1010 / H:17 / S:60 515072 kB (FAT16/6) spc=16,spf=0xFC: works
- C: 1011 / H:31 / S:62 948 MB (FAT16/6) spc=32,spf=0xEE: works
Heads and Sectors working with Corel LS2000 BIOS (v1.65):
Tested with 386SX and does NOT work with an 8088!:
- C: 961 / H:17 / S:8 63.1 MB (FAT16/6) spc=4,spf=0x80: works
- C: 961 / H:17 / S:16 127.6 MB (FAT16/6) spc=4,spf=0xFF: works
- C: 1021 / H:32 / S:16 255.5 MB (FAT16/6) spc=16,spf=0x80: works
- C: 597 / H:64 / S:16 299 MB (FAT16/6) spc=16,spf=0x96: works
- C: 1003 / H:64 / S:16 502 MB (FAT16/6) spc=16,spf=0xFB: works
- C: 1019 / H:64 / S:16 509.9 MB (FAT16/6) spc=16,spf=0xFF: works
- C: 570 / H:64 / S:32 570.5 MB (FAT16/6) spc=32,spf=0x8F: works
- C: 571 / H:64 / S:32 572 MB (FAT16/6) spc=32,spf=0x8F: works
- C: 667 / H:64 / S:32 668 MB (FAT16/6) spc=32,spf=0xA7: works
- C: 762 / H:64 / S:32 763 MB (FAT16/6) spc=32,spf=0xBF: works
- C: 859 / H:64 / S:32 860 MB (FAT16/6) spc=32,spf=0xD7: works
- C: 903 / H:64 / S:32 904 MB (FAT16/6) spc=32,spf=0xE2: works
- C: 927 / H:64 / S:32 927.9 MB (FAT16/6) spc=32,spf=0xE8: works
- C: 1019 / H:64 / S:32 1020 MB (FAT16/6) spc=32,spf=0xFF: works
- C: 946 / H:64 / S:32 947 MB (FAT16/6) spc=32,spf=0xED: doesn't work
- C: 946 / H:64 / S:32 947 MB (FAT16/6) spc=32,spf=0xFB: doesn't work
It should be said that the Corel Drivers and BIOS is the way to go!
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P12.50mm_Horizontal | C2, C3, C4, C5 |
| 3 | 330E | Resistor_THT:R_Array_SIP8 | Z3, Z4, Z5 |
| 2 | ? | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X12, X17 |
| 2 | ? | Inductor_THT:L_Axial_L5.3mm_D2.2mm_P10.16mm_Horizontal_Vishay_IM-1 | FB1, FB2 |
| 1 | 100n | Capacitor_THT:C_Rect_L9.0mm_W2.5mm_P7.50mm_MKT | C99 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R2 |
| 1 | 15p | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P12.50mm_Horizontal | C7 |
| 1 | 16M | Crystal:Crystal_HC49-U_Vertical | Y2 |
| 1 | 1k | Resistor_THT:R_Array_SIP6 | Z2 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1 |
| 1 | 22u/35 | Capacitor_THT:C_Axial_L12.0mm_D6.5mm_P20.00mm_Horizontal | C6 |
| 1 | 27C128 | Package_DIP:DIP-28_W15.24mm_Socket_LongPads | U1 |
| 1 | 2A | Inductor_THT:L_Axial_L5.3mm_D2.2mm_P10.16mm_Horizontal_Vishay_IM-1 | F1 |
| 1 | 47p | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P12.50mm_Horizontal | C8 |
| 1 | 4k7 | Resistor_THT:R_Array_SIP4 | Z1 |
| 1 | 4k7 | Resistor_THT:R_Array_SIP6 | Z6 |
| 1 | 53C400 | Package_LCC:PLCC-68_THT-Socket | U2 |
| 1 | 56p | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P12.50mm_Horizontal | C10 |
| 1 | 68p | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P12.50mm_Horizontal | C9 |
| 1 | 74LS244 | Package_DIP:DIP-20_W7.62mm_LongPads | U6 |
| 1 | 74LS245 | Package_DIP:DIP-20_W7.62mm_LongPads | U3 |
| 1 | 9M6 | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | ADDRSEL | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | X4 |
| 1 | BOOTDIS | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X16 |
| 1 | BUSRSTDLY | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X18 |
| 1 | Bus_ISA_8bit | my_own_conn:BUS_XT | P1 |
| 1 | ENABLE | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X13 |
| 1 | FDC | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | X3 |
| 1 | Floppy Internal | Connector_PinHeader_2.54mm:PinHeader_2x17_P2.54mm_Vertical | J3 |
| 1 | GAL20V10 | Package_DIP:DIP-24_W7.62mm_Socket_LongPads | U4 |
| 1 | IRQSEL | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X8 |
| 1 | IRQSEL | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | X11 |
| 1 | MCA | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X14 |
| 1 | SCSI Intern | Connector_PinHeader_2.54mm:PinHeader_2x25_P2.54mm_Vertical | J2 |
| 1 | SYQUEST | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X15 |
| 1 | TERMPWR | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | X7 |
| 1 | WD37C65 | Package_LCC:PLCC-44_THT-Socket | U5 |
Similar boards
- 2 layers222.3 × 88.9 mm

- 2 layers239.6 × 239.9 mm

- 2 layers135 × 97.8 mm

- 2 layers82 × 76 mm

OPD Computer One Disk Interface
stephen-usher/OPD-Computer-One-Disk-Interface
Recreation of the Computer One floppy disk interface for the ICL One Per Desk.
22 parts1CC0-1.0 - 2 layers129.5 × 100 mm

Ql Cumana
alvaroalea/QL_Cumana_FLoppyController
A clone of the Cumana's Disk Interface for the Sinclair QL
40 partsCERN-OHL-S-2.0 - 2 layers100 × 85 mm

- 2 layers100 × 80 mm

- 2 layers164.5 × 89.5 mm

Questions
How big is the Rancho RT1000 SCSI Controller PCB?
It measures 135 × 108 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rancho RT1000 SCSI Controller use?
44 parts, built around the 74LS245SC and 27C128-15. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rancho RT1000 SCSI Controller KiCad files?
From the roberto314/Rancho-RT1000-SCSI-8-Bit repository on GitHub, at the commit this page was made from: the board is schematic/Rancho RT1000/Rancho RT1000 SCSI Controller.kicad_pcb and its schematic schematic/Rancho RT1000/Rancho RT1000 SCSI Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rancho RT1000 SCSI Controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask roberto314 before reusing the design.