

CATS
An ESP32 system to add some spark into my '00 Z3M
- Size
- 86 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 58
- Pads
- 143
- Tracks, vias
- 170, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 26 Sep 2026
- Updated
- 26 Sep 2026
Overview
CATS is an open-source printed circuit board by rickwargo, from the rickwargo/CATS repository on GitHub. It is a 2-layer board of 86 × 70 mm with 30 parts on 58 nets, routed with 170 tracks and 0 vias.
It is built around the ESP32-S3-DEVKITM-1-N8, SN65HVD230D and MP1584EN, with the MPU-6050 and PESD5V0L2BT among its other parts. Its parts include 7 resistors, 7 connectors, 6 ICs, 5 capacitors and 1 diode. It belongs with the ESP32 boards of this library.
Main components
5ESP32-S3-DEVKITM-1-N8
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversMP1584EN
SOIC-8-EP-20℃~+85℃ 1 100kHz~1.5MHz 4.5V~28V Adjustable Buck Buck Built-in SOIC-8-EP DC-DC Converters ROHSMonolithic Power SystemsDC-DC ConvertersMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometersPESD5V0L2BT
SOT-23-65℃~+150℃ 13A@8/20us 1uA 2 26V 350W@8/20us 5V 7.6V 75pF Bidirectional ESD IEC 61000-4-2 SOT-23 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10K | Resistor_SMD:R_1206_3216Metric | R8, R9, R10 |
| 3 | MountingHole_2.2mm_M2 | MountingHole:MountingHole_2.2mm_M2 | , , |
| 2 | 10R | Resistor_SMD:R_1206_3216Metric | R3, R4 |
| 2 | 47pF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4, C5 |
| 2 | Conn_01x05 | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J6, J7 |
| 1 | 0.1uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C8 |
| 1 | 0R | Resistor_SMD:R_1206_3216Metric | R1 |
| 1 | 100nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 4K7 | Resistor_SMD:R_1206_3216Metric | R2 |
| 1 | BME-680 | !Personal:BME-680 | U6 |
| 1 | Barrel_Jack | !Personal:BarrelJack_Horizontal | J1 |
| 1 | Buzzer | !Personal:Passive Buzzer | BZ1 |
| 1 | Conn_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J4 |
| 1 | Conn_01x03 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | Conn_01x04 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5 |
| 1 | Conn_01x07 | Connector_JST:JST_XH_B7B-XH-A_1x07_P2.50mm_Vertical | J3 |
| 1 | ESP32-S3-DevKitM-1-N8 | !Personal:ESP32-S3-DevKitM-1-N8 | U1 |
| 1 | MP1584EN | !Personal:MP1584EN_DCDC_THT_Module | U2 |
| 1 | MPU-6050 | !Personal:MPU-6500 | U8 |
| 1 | Micro_SD_Card | !Personal:Micro_SD_Card | U5 |
| 1 | PESD5V0L2BT | Package_TO_SOT_SMD:SOT-23 | D8 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
More from rickwargo/CATS
4- 2 layers75.6 × 64.1 mm

- 2 layers117.1 × 86 mm

- 2 layers35 × 50 mm

- 2 layers20 × 15 mm

Similar boards
- 2 layers61 × 177.8 mm

Motor control + ESP
Scramtv/ESD_P5
Github repo for our group through fifth semester of Electronics and Systems design on AAU.
16 parts - 2 layers99.1 × 99.1 mm

- 2 layers95 × 100 mm

Driver Carrier v2
Vinomakon/VEPR-Robotarm
A personal robotics project bringing together a 3D-printed six-axis arm, custom motor-driver electronics, ESP32 firmware, and a Python desktop control panel.
33 parts - 2 layers419.1 × 101.2 mm

- 4 layers111 × 171 mm

Network and Switch
AkshathRaghav/boilernet
Code release for BoilerNet, demo'd at SPARK S'25 as a Purdue Senior Design Capstone. Associated PCB Design and 3D Prints within.
108 parts3Apache-2.0 - 4 layers100 × 100 mm

PS BPSLeader
lhr-solar/PS-BPSLeader
Reads voltage, temperature, and current of the main battery pack from the Segment Monitoring Board and HV Carrier boards to ensure the battery remains in a safe state.
388 parts3MIT - 8 layers134.5 × 107.2 mm

- 2 layers450 × 400 mm

Questions
How big is the CATS PCB?
It measures 86 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the CATS use?
30 parts, built around the ESP32-S3-DEVKITM-1-N8, SN65HVD230D, MP1584EN and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CATS KiCad files?
From the rickwargo/CATS repository on GitHub, at the commit this page was made from: the board is CATS.kicad_pcb and its schematic Blower Switch/Switcher.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CATS design in my own project?
Its repository states no licence, so its author keeps all rights: ask rickwargo before reusing the design.