2 layers32 × 53.5 mm
Toto fc
tact1m4n3/toto-flight-old
My attempt at writing a flight controller for an rc fixed wing craft.
46 partsMIT
2 layers64.3 × 73.3 mm
Arkan1
rasthpop/arkan_POC2- Size
- 64.3 × 73.3 mm
- Copper layers
- 2
- Thickness
- 1.5 mm
- Parts
- 43
- Nets
- 81
- Pads
- 257
- Tracks, vias
- 344, 48
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 Oct 2025
- Updated
- 11 Dec 2025
Overview
Arkan1 is an open-source printed circuit board by rasthpop, from the rasthpop/arkan_POC repository on GitHub. It is a 2-layer board of 64.3 × 73.3 mm with 43 parts on 81 nets, routed with 344 tracks and 48 vias.
It is built around the 24LC32A/P, DW01A and TP4056-42-ESOP8, with the TPS79133DBVREP among its other parts. Its parts include 11 resistors, 10 capacitors, 6 ICs, 3 diodes and 3 transistors. It belongs with the RP2040 boards of this library.
Main components
4
24LC32A/P
PDIP-80℃~+70℃ 2.5V~5.5V 32Kbit 400kHz 5ms I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROM
DW01A
SOT-23-6L-40℃~+85℃ 1 2.5V 300mV~10V 3uA 4.3V Protection IC Support SOT-23-6L Battery Management ROHSPUOLOPBattery Management
TP4056-42-ESOP8
ESOP-8-40℃~+85℃ 1 1A 2uA 4.2V 4V~8V Charging IC Lithium Battery Support ESOP-8 Battery Management ROHSTOPPOWERBattery Management
TPS79133DBVREP
SOT-23-5-40℃~+125℃@(Tj) 1 100mA 250uA 3.3V 37dB@(100kHz) 5.5V 90mV@(100mA) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdAutonomous Radio-Beacon Coordinator for Air Reconnaissance and Warning (ARCAN)
Software Usage
Clean Target
cargo cleanBuild
cargo build --releaseRun
IMPORTANT: Pico has to be connected to your pc and the bootloader button on the mcu has to be press-held!
cargo run --releaseLog Data from Pico and Launch Terminal
sudo apt install tiosudo tio /dev/ttyACM0Parts
43| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 1 kO | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R9, R10 |
| 3 | LED | LED_SMD:LED_0805_2012Metric | D1, D2, D3 |
| 2 | 0.1 uF | Capacitor_SMD:C_0603_1608Metric | C9, C10 |
| 2 | 10 kO | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R13 |
| 2 | 100 nF | Capacitor_Tantalum_SMD:CP_EIA-7343-31_Kemet-D | C4, C5 |
| 2 | 100 nF | Capacitor_SMD:C_0603_1608Metric | C1, C3 |
| 2 | 5.1 kO | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R7 |
| 1 | 0.01 uF | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 0.1 nF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 1 uF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 1 uf | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 1.1 kO | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 100 O | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 22 O | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 1 | 24LC32 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | 27 uH | Inductor_SMD:L_1210_3225Metric | L1 |
| 1 | Ai-Thinker-Ra-02 | RF_Module:Ai-Thinker-Ra-01-LoRa | U2 |
| 1 | Conn_01x02 | Connector_AMASS:AMASS_XT30U-M_1x02_P5.0mm_Vertical | J1 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | J4 |
| 1 | DW01A | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | GY-NEO6MV2 | GY-NEO6MV2 (1):XCVR_GY-NEO6MV2 | U4 |
| 1 | LOGO | rdhead_logo:logosmall | G*** |
| 1 | NMOS (CHG) | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | NMOS (DSG) | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | PMOS | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | RaspberryPi_Pico | Module:RaspberryPi_Pico_Common_SMD | A1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_PTS645Sx43SMTR92 | SW1 |
| 1 | TP4056-42-ESOP8 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.81mm | U3 |
| 1 | TPS79133DBVR | TPS79133DBVR:SOT95P280X145-5N | U5 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
The 40 most common of 43 parts.
Similar boards
- 2 layers60 × 111.3 mm
Silkscreen pcb
iandchasse/silkscreen-pcb
Silkscreen: open-hardware ESP32-S3 e-paper reader mainboard (KiCad 9). Formerly the de-link hub.
189 parts589CERN-OHL-S-2.0 - 2 layers51 × 21 mm
FOX JACK EXT BOARD TOP
KaliAssistant/Fox-Jack
Portable social-engineering LAN tool for automated payloads and wired audits — based on Luckfox Pico Max
35 parts22GPL-3.0 - 2 layers61 × 61 mm
ESP32 FC
MAATHES-THILAK-K/ESP32-S3_FLIGHT_CONTROLLER
A custom-designed flight controller based on the ESP32-S3 module, built for compatibility with the esp-fc firmware and Betaflight-like configuration.
69 parts7Apache-2.0 - 2 layers147 × 105.9 mm
WirelessControllerESP32
EmmetGameDev/NevoltaNexusConsole
Repository for design files and code for the Nexus console.
66 parts4GPL-3.0 - 2 layers51.1 × 95 mm
Talk e
milovanpms/talk-e
📻 — A simple LoRa-based talkie-walkie built on ESP32, operating on the 433 MHz frequency band for long-range, low-power wireless communication.
75 parts4 - 4 layers340.8 × 104.6 mm
Niphar
mornepousse/Niphargus
Niphargus — a slim, indestructible wireless split keyboard. ESP32 + nRF24, wired fallback, and an emergency kit hidden behind the USB port. The successor to the Rouge-Gorge.
287 parts4MIT - 2 layers80 × 34 mm
Dji fcc
nikolaus018/dji-fcc-esp32
ESP32-S3 firmware that switches a DJI N1 remote to FCC mode over USB (replaces the Android app)
69 parts3MIT
Questions
How big is the Arkan1 PCB?
It measures 64.3 × 73.3 mm and has 2 copper layers, 1.5 mm thick.
What parts does the Arkan1 use?
43 parts, built around the 24LC32A/P, DW01A, TP4056-42-ESOP8 and TPS79133DBVREP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Arkan1 KiCad files?
From the rasthpop/arkan_POC repository on GitHub, at the commit this page was made from: the board is arkan1.kicad_pcb and its schematic arkan1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Arkan1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask rasthpop before reusing the design.