Skip to the content
2 layers61.6 × 48.9 mmPCB milli, the printed circuit board in 3D

Portable and low cost milliommeter with good performances

Size
61.6 × 48.9 mm
Copper layers
2
Thickness
1.58 mm
Parts
24
Nets
10
Pads
54
Tracks, vias
51, 0
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
22 May 2025
Updated
22 May 2025

Overview

PCB milli is an open-source printed circuit board by Pronoe, from the Pronoe/millihom-meter repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 61.6 × 48.9 mm with 24 parts on 10 nets, routed with 51 tracks and 0 vias.

It is built around the TLC272CD and BC548. Its parts include 5 resistors, 3 capacitors, 2 ICs, 1 diode and 1 transistor.

Main components

2

README

README.md

milliohm-meter

Portable and low cost milliommeter with good performances

Introduction

When you have to debug electronic systems or find failure on an electronic board or electrical system, you frequently need to locate short circuits. Common multimeters are generally limited down to 1 ohm in their measurement and this is not sufficient for efficient characterization and localization of a short circuit. Below the 1 ohm domain, a milliohmmemeter is the required instrument but Industrial miiliohmmeters are expensive so I decided to build my own device.

General design

I had viewed a good publication for a DIY milliohmmeter from the "Electro-bidouilleur" YouTube channel. The Elektor magazine sells also a add-on device for multimeters. However this projects suffers several drawbacks:

  • need a separate multimeter for the measurement
  • provides no protection against excessive voltage on the device under test
  • do not use 4 wires measurement for better accuracy The main characteristics of my design are:
  • use of a INA199 from Texas Instrument for the measurement o this is a Voltage-Output, Current-Shunt Monitor which need no additional component o provides very low offset voltage and very low drift o high accuracy gain
  • current source of 10.6 mA build with a ½ TLC272 which is a precision dual operational amplifier
  • voltage limiter with a BC548 transistor
  • use of and Arduino Uno board for: o output voltage measurement, o resistance computation from voltage measurement o initial zero compensation o full range calibration
  • use of a 2 lines x 16 characters LCD display shield for user interface
  • use of a a 1200 mAh LiPo battery combined with a step up converter/ battery charger for portable operation
  • use of a "Kelvin" 4 wires cable for device connection

see detailed information in technical files

Parts

24
QtyValueFootprintReferences
4MountingHoleMountingHole:MountingHole_3.2mm_M3H8, H9, H10, H11
2100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC1, C2
21kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R5
2470Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R4
1100Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
147uCapacitor_THT:CP_Axial_L11.0mm_D6.0mm_P18.00mm_HorizontalC3
1BA315Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1
1BC548Package_TO_SOT_THT:TO-92_InlineQ1
1GNDConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH2
1IC+Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH6
1IC-Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH5
1IN+Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH3
1IN-Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH4
1INA199xxDCKPackage_TO_SOT_SMD:SOT-363_SC-70-6U1
1ProbeTestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mmTP1
1TLC272Package_DIP:DIP-8_W7.62mmU2
1VCCConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH1
1VOUTConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm_ReliefH7

Similar boards

  • 2 layers85 × 61 mmGBDSO, the printed circuit board in 3D

    GBDSO

    pyroesp/GBDSO

    Game Boy DSO Project revived in KiCad

    78 parts79
  • 2 layers200 × 87.8 mmSonus7 rev1, the printed circuit board in 3D

    Sonus7 rev1

    BasementCircuits/Sonus7

    Analog seven-band spectrum bargraph with op amps.

    263 parts6
  • 2 layers52.3 × 51.8 mmReBlast, the printed circuit board in 3D

    ReBlast

    SukkoPera/ReBlast

    8-Bit DAC/ADC Add-On for Commodore 16/Plus4 SIDcards

    27 parts6
  • 2 layers92.5 × 99.7 mmOpamp vu meter, the printed circuit board in 3D

    Opamp vu meter

    CASE-Association/christmas-cards

    All CASE christmas cards over the years

    48 parts3GPL-3.0
  • 2 layers50 × 40.9 mmGR ATTiny LFO, the printed circuit board in 3D

    GR ATTiny LFO

    GadgetReboot/ATTiny_LFO

    Dual low frequency oscillators using ATTiny and MCP4725 DACs

    36 parts3
  • 2 layers56.5 × 74 mmAscom flat panel, the printed circuit board in 3D

    Ascom flat panel

    letelescope/ascom-flat-panel

    Open source ASCOM and INDI driven automated flat panel for astrophotography

    17 parts2MIT
  • 2 layers43.5 × 46.9 mmSchaltplan Ultraschallsensor, the printed circuit board in 3D

    Schaltplan Ultraschallsensor

    Tinkerforge/distance-us-v2-bricklet-techniker

    This repository contains the firmware source code and the hardware design files. The documentation generator configs can be found at https://github.com/Tinkerforge/generators

    54 parts2
  • 2 layers85 × 56.5 mmMotherboard, the printed circuit board in 3D

    Motherboard

    BryggansBryggeri/electrical

    Electronics, hardware schematics

    34 parts1

Questions

How big is the PCB milli PCB?

It measures 61.6 × 48.9 mm and has 2 copper layers, 1.58 mm thick.

What parts does the PCB milli use?

24 parts, built around the TLC272CD and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCB milli KiCad files?

From the Pronoe/millihom-meter repository on GitHub, at the commit this page was made from: the board is pcb_Kicad/PCB_milli.kicad_pcb and its schematic pcb_Kicad/PCB_milli.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCB milli design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).