
ZArduino
zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

In high school I had this idea of a thing I wanted to build. I wanted to make a thing that got roms out of GBA cartridges. I had no idea what knowledge I needed to gain to be able to execute on it.
One is an open-source printed circuit board by princess-garchomp, from the princess-garchomp/GBA_card_reader_STM32 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 63.8 × 103.5 mm with 43 parts on 85 nets, routed with 453 tracks and 29 vias.
It is built around the FT232RL and TPS76901DBV. Its parts include 15 resistors, 14 connectors, 9 capacitors, 3 ICs and 1 fuse. It belongs with the STM32 boards of this library.
In high school I had this idea of a thing I wanted to build. I wanted to make a thing that got roms out of GBA cartridges. I had no idea what knowledge I needed to gain to be able to execute on it. two degrees and three employers latter I knew enough to start this project. at this point, people have figured out this problem almost completely. but I still wanted to do it myself.
I got my solution to the point of reading data out of the roms but then lost intereset, I had completed most of what I wanted to. because this problem has been solved by others, I did not need to get funcitong game files just some meaningfull data indicating my sytem worked.
partly I gave up to spend time looking for a new job. now that I am not on the search for a better job, I am going to re-start this project.
inital commits are what I found on my computer that I think were relevant. there may be more.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100k | Resistor_SMD:R_0402_1005Metric | R2, R4, R7, R13, R14, R15 |
| 5 | 100nF | Capacitor_SMD:C_0402_1005Metric | C2, C3, C5, C8, C9 |
| 3 | 3k | Resistor_SMD:R_0402_1005Metric | R5, R8, R11 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J12, J13, pwr_en |
| 2 | 150k | Resistor_SMD:R_0402_1005Metric | R1, R6 |
| 2 | 20pF | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 1 | 160k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 1uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C4 |
| 1 | 200k | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 30k | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 4.7uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B | C1 |
| 1 | 66.5k | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 8MHZ crystal | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J8 |
| 1 | Conn_01x10_Pin | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J11 |
| 1 | FT232RL | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U2 |
| 1 | Fuse | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | TPS76901 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | USB_A | Connector_USB:USB_A_Molex_67643_Horizontal | J1 |
| 1 | boot0 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | boot1 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | ft232_1 | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J14 |
| 1 | ft232_2 | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J15 |
| 1 | gba_breakout | Connector_PinHeader_2.54mm:PinHeader_1x38_P2.54mm_Vertical | J5 |
| 1 | gba_breakout2 | Connector_PinHeader_2.54mm:PinHeader_1x38_P2.54mm_Vertical | J10 |
| 1 | reset_button | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | rst |
| 1 | swdb | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J7 |
| 1 | uart_jumper | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J4 |

zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube



Ledger-Donjon/silicon-toaster
SiliconToaster is an open-source hardware electromagnetic fault injection device, designed for hardware security research. It has the following features:


jsjolund/dmx512-controller-board
Controller board for DMX512 compatible devices, built around the STM32F4 processor

It measures 63.8 × 103.5 mm and has 2 copper layers, 1.6 mm thick.
43 parts, built around the FT232RL and TPS76901DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the princess-garchomp/GBA_card_reader_STM32 repository on GitHub, at the commit this page was made from: the board is hardware/one.kicad_pcb and its schematic hardware/one.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).