

SiPM Characterisation RevD Mount10
Silicon photomultipliers (SiPMs) require a stable reverse-bias voltage and a low-noise signal interface for meaningful characterization.
- Size
- 174 × 88 mm
- Copper layers
- 2
- Thickness
- 1.4 mm
- Parts
- 65
- Nets
- 29
- Pads
- 191
- Tracks, vias
- 330, 22
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 4 Aug 2026
- Updated
- 4 Aug 2026
Overview
SiPM Characterisation RevD Mount10 is an open-source printed circuit board by prat4002, from the prat4002/PCB-for-SiPM-characterisation repository on GitHub. It is a 2-layer board of 174 × 88 mm with 65 parts on 29 nets, routed with 330 tracks and 22 vias.
It is built around the LT3571IUD#PBF, TMP117AIDRVR and TPS7A2033PDBVR-TP, with the AFBR-S4N66P014M among its other parts. Its parts include 21 resistors, 14 capacitors, 7 connectors, 4 diodes and 3 ICs.
Main components
4LT3571IUD#PBF
QFN-16-EP(3x3)-40℃~+125℃@(TJ) 1 2.7V~20V 250kHz~2MHz 370mA Boost Boost Built-in QFN-16-EP(3x3) DC-DC Converters ROHSAnalog DevicesDC-DC ConvertersTMP117AIDRVR
WDFN-6-EP(2x2)-55℃~+150℃ 1.7V~5.5V 15.5ms 16bit 3.1uA Factory temperature calibration、Temperature threshold monitoring、Low-power standby、On-chip non-volatile parameter storage、On-chip digital filtering/averaging I2C、SMBus ±0.1℃ WDFN-6-EP(2x2) Temperature Sensors ROHSTexas InstrumentsTemperature SensorsTPS7A2033PDBVR-TP
SOT-23-5-40℃~+85℃ 1 180uV@(300mA) 2uA 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Current Protection、Enable、Thermal Shutdown Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICUncategorisedAFBR-S4N66P014M
-1 250nm~900nm 420nm 8.6uA - Photodiodes ROHSBroadcom LimitedPhotodiodes
README
README.mdUSB-Powered SiPM Characterisation PCB
Why this PCB was created
Silicon photomultipliers (SiPMs) require a stable reverse-bias voltage and a low-noise signal interface for meaningful characterization. A laboratory setup made from separate power supplies, current meters, bias resistors, and amplifier modules is difficult to reproduce and can introduce wiring errors, noise, and uncertain voltage drops.
This project combines those functions into one reusable characterization board for the Broadcom AFBR-S4N66P014M NUV-MT SiPM. The board is intended to support measurement of breakdown voltage, gain, photon detection efficiency, dark count rate, optical crosstalk, and afterpulsing. The same bias and pulse-readout sections can also be reused in a future PSD spectrometer project.
Project in brief
The board accepts regulated 5 V power through USB-C. Input protection and filtering feed a quiet 3.3 V analog rail and the LT3571 high-voltage boost converter. The LT3571 generates the adjustable SiPM reverse bias, with a hardware-limited manual multi-turn control and a maximum board marking of 45 V.
The high-voltage output is filtered before reaching the SiPM. A separate high-value divider monitors the actual post-filter SiPM voltage. The SiPM current can be measured externally through the DMM/picoammeter terminals, while the fast avalanche signal is AC-coupled to a 50 ohm SMA output for an oscilloscope or digitizer.
Main user-accessible functions:
J1: USB-C 5 V input.RV1: multi-turn manual bias adjustment.TP5: filtered bias-control test point.J4/J5: DMM terminals for monitored high voltage and analog ground.J6/J7: current-measurement insertion terminals in the SiPM anode return path.J2: 50 ohm fast pulse output for an oscilloscope or digitizer.TP8: pulse-output test point.TP3: analog-ground test point.D5: AFBR-S4N66P014M SiPM footprint.
The board is designed for instrument-only operation. A microcontroller is optional and is not required for manual bias adjustment, DMM measurements, or oscilloscope measurements.
How to use the board
Before powering the board
- Install the SiPM in the
D5footprint with the correct orientation and ESD precautions. - Place the assembly in a light-tight enclosure for dark measurements.
- Turn the manual bias control fully toward the minimum-bias setting.
- Confirm that the USB input is a regulated 5 V source.
- Connect the oscilloscope or digitizer to
J2with a short 50 ohm coaxial cable if pulse measurements are required. - Connect the DMM to
J4andJ5to measure the actual post-filter bias voltage. Use the correct high-voltage range on the DMM. - For current measurements, insert the ammeter or picoammeter in series between
J6andJ7. Never connect an ammeter directly across a voltage source.
Power-up and bias adjustment
- Apply 5 V through USB-C.
- Verify the low-voltage rail and ground at the available test points.
- Slowly rotate
RV1while watching the DMM connected toJ4/J5. - Increase the SiPM terminal voltage in controlled steps. The actual voltage at the detector terminals, rather than the converter feedback node, is the value to record.
- Do not exceed the 45 V board limit or the SiPM datasheet current and voltage limits.
- After a measurement, reduce the bias to its minimum setting and allow the bleed network to discharge the high-voltage node before disconnecting equipment.
SiPM characterization procedure
Breakdown voltage and dark I-V
- Use a light-tight enclosure and block all optical illumination.
- Begin at a bias safely below the expected breakdown region.
- Increase the voltage in coarse steps while the current is small.
- Use smaller voltage steps near the rapid increase in avalanche current.
- At every point, record actual SiPM voltage, SiPM current, temperature, and settling time.
- Stop before reaching the hardware voltage or current limit.
- Estimate
VBDusing the slope or inverse-log-derivative of the I-V data, and compare it with a gain-versus-voltage extrapolation.
Gain and single-photoelectron response
- Connect
J2to a 50 ohm oscilloscope or digitizer. - Illuminate the SiPM with a weak pulsed LED or laser source.
- Set the light level low enough that individual photoelectron events remain distinguishable.
- Record waveforms at several overvoltages above the measured breakdown voltage.
- Subtract a fixed baseline and integrate each pulse over the same time window.
- Build a charge histogram containing the pedestal and photoelectron peaks.
- Calculate gain from
G = Q_1pe / e, whereeis the elementary charge. - Plot gain against bias voltage and extrapolate the approximately linear trend toward zero gain to obtain a gain-derived breakdown estimate.
PDE, dark count, crosstalk, and afterpulsing
PDE measurements require a calibrated optical source or calibrated reference photodiode. Record wavelength, optical power or pulse energy, repetition rate, geometry, and active area. Measure dark counts at the same bias and temperature, subtract the dark contribution, and correct for correlated noise and acquisition dead time where necessary.
For dark count rate, block the light source and count threshold crossings over a known time interval. For optical crosstalk, compare rates above approximately 0.5, 1.5, and 2.5 photoelectron thresholds. For afterpulsing, examine delayed pulses following a primary avalanche within a defined timing window.
Verification
The canonical PCB was checked with KiCad command-line tools after the final AGND-zone refill:
- PCB DRC violations:
0 - Unconnected items:
0 - Standard footprint errors:
0 - Schematic ERC errors:
0 - Schematic ERC warnings:
0
The four M3 mounting-hole centers are positioned 10 mm from the adjacent board edges. Connector positions were adjusted to preserve mechanical clearance.
The four mounting holes are mechanical PCB-only features and therefore appear as intentional extra footprints if schematic-parity checking is enabled. This does not affect Gerber fabrication, but any future electrical revision should update the schematic and PCB together.
Before fabrication, the manufacturer should still perform its normal DFM review. Confirm the SiPM part, all populated component manufacturer part numbers, assembly polarity, and the intended DNP options before ordering assembled boards.
Repository layout
- Root
*.kicad_pro,*.kicad_pcb, and*.kicad_sch: canonical editable KiCad project files. fp-lib-tableandsym-lib-table: project-local library configuration.libraries/: external footprints, symbols, and 3D models required to open the project correctly.fabrication/: current Gerbers, Excellon drill file, drill map, job data, DRC/ERC reports, BOM, and pick-and-place files.documentation/: design verification, characterization procedure, project report, and schematic PDF.cost/: component cost estimate in INR.presentation/: presentation prepared for project handover.
The authoritative routed source is SiPM_Characterisation_RevD_Mount10.kicad_pcb. Before changing the electrical design, open the project in KiCad, review the schematic-to-PCB netlist, and update both sources together.
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_3.2mm_M3 | MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 10k HV filter | Resistor_SMD:R_1206_3216Metric | R10, R11 |
| 2 | 2.00M 0.1% | Resistor_SMD:R_1206_3216Metric | R14, R15 |
| 1 | +3V3_A | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | +5V_A | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | 0.22uF 100V X7R | Capacitor_SMD:C_1206_3216Metric | C6 |
| 1 | 100k 0.1% | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 100k SHDN pull-up | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | 100k bias feed | Resistor_SMD:R_1206_3216Metric | R13 |
| 1 | 100nF 50V X7R | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 100nF SHDN soft-start | Capacitor_SMD:C_0603_1608Metric | C16 |
| 1 | 100nF TMP117 bypass | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 10k bottom stop | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 10k top stop | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 10k wiper filter | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 10nF VREF bypass | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 10nF monitor filter | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 10uF 10V X7R | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 1M baseline return | Resistor_SMD:R_0603_1608Metric | R22 |
| 1 | 1nF C0G AC coupling | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | 1uF 10V LT3571 local VIN | Capacitor_SMD:C_0805_2012Metric | C18 |
| 1 | 1uF 10V X7R | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 1uF CTRL filter | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 1uF TPS7A20 OUT | Capacitor_SMD:C_0805_2012Metric | C14 |
| 1 | 2.00M bleed | Resistor_SMD:R_1206_3216Metric | R12 |
| 1 | 2.10M 0.1% HV LIMIT | Resistor_SMD:R_1210_3225Metric | R4 |
| 1 | 33.2k RT | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 4.7k SCL pull-up | Resistor_SMD:R_0603_1608Metric | R24 |
| 1 | 4.7k SDA pull-up | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 4.7nF 100V | Capacitor_SMD:C_1206_3216Metric | C9 |
| 1 | 41.2k 0.1% | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 5.1k CC1 | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 5.1k CC2 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 75R MON current limit | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | AFBR-S4N66P014M | Broadcom:AFBRS4N66P014M | D5 |
| 1 | AGND | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | Bourns 3296W 25k 10-turn | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | CTRL | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | DNP 1M anode return | Resistor_SMD:R_1206_3216Metric | R26 |
| 1 | DNP 1nF 100V | Capacitor_SMD:C_1206_3216Metric | C10 |
| 1 | DNP CTRL clamp | Diode_SMD:D_SOD-323 | D2 |
| 1 | DNP RF clamp | Diode_SMD:D_SOD-323 | D3 |
| 1 | GCT USB4105-GF-A | RevD:USB4105_0p8mm_slots | J1 |
| 1 | HV_CATHODE | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | HV_MON | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | I2C TEMP +3V3/SCL/SDA/GND | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | LT3571IUD#PBF | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm | U1 |
| 1 | Littelfuse 1206L050WR | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | Murata BLM21PG221SN1D | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | PESD5V0S1BA,115 VBUS TVS | Diode_SMD:D_SOD-323 | D1 |
| 1 | PULSE_AC | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | Pomona 73099-0 BLACK DMM I AGND | Pomona:Pomona_73099 | J7 |
| 1 | Pomona 73099-0 BLACK DMM V AGND | Pomona:Pomona_73099 | J5 |
| 1 | Pomona 73099-2 RED DMM I SiPM ANODE | Pomona:Pomona_73099 | J6 |
| 1 | Pomona 73099-2 RED DMM V HV MON | Pomona:Pomona_73099 | J4 |
| 1 | SMA_DIRECT | Connector_Coaxial:SMA_Amphenol_132289_EdgeMount | J2 |
| 1 | TEMP_ALERT | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | TMP117AIDRVR | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U9 |
| 1 | TPS7A2033PDBVR | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | Wurth 744043150 15uH | RevD:WE_744043150 | L1 |
Similar boards
- 2 layers95 × 50 mm

- 4 layers39 × 39 mm

OneInchEye
will127534/OneInchEye
A One Inch CMOS sensor (IMX283) camera board designed for Raspberry Pi
94 parts355MIT - 4 layers121 × 87.9 mm

- 4 layers39 × 39 mm

ShutterEye
will127534/ShutterEye
A simple camera board using SC910GS 1" 4K@30fps global shutter sensor
157 parts26MIT - 4 layers60 × 40 mm

Ftx
SETIatHCRO/Front-Page
Documentation related to the Allen Telescope Array at the Hat Creek Radio Observatory Wiki Link Below
153 parts5 - 4 layers44.5 × 50.6 mm

- 2 layers56 × 6.2 mm

- 2 layers228.9 × 5.5 mm

TMP117 section 5cm
BerkeleyLab/DxP-sensor-probes
Hardware design for the DxP (Distributed sensor Profiling) sensor probe.
38 parts1
Questions
How big is the SiPM Characterisation RevD Mount10 PCB?
It measures 174 × 88 mm and has 2 copper layers, 1.4 mm thick.
What parts does the SiPM Characterisation RevD Mount10 use?
65 parts, built around the LT3571IUD#PBF, TMP117AIDRVR, TPS7A2033PDBVR-TP and AFBR-S4N66P014M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SiPM Characterisation RevD Mount10 KiCad files?
From the prat4002/PCB-for-SiPM-characterisation repository on GitHub, at the commit this page was made from: the board is SiPM_Characterisation_RevD_Mount10.kicad_pcb and its schematic SiPM_Characterisation_RevD_Mount10.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SiPM Characterisation RevD Mount10 design in my own project?
Its repository states no licence, so its author keeps all rights: ask prat4002 before reusing the design.