
Emg
Pai-88/emg-robotic-hand
Single-channel surface-EMG front end (AD623 + driven-right-leg) on a Raspberry Pi Pico. Board fabricated and telemetry verified on hardware; analog front end and on-body EMG still in bring-up.

stm32f103 handheld oscilloscope
Osilloscopen is an open-source printed circuit board by pondahai, from the pondahai/oscilloscopen repository on GitHub. It is a 2-layer board of 190 × 30 mm with 63 parts on 56 nets, routed with 542 tracks and 11 vias.
It is built around the AD623AN and ICL7660N. Its parts include 19 connectors, 15 resistors, 11 capacitors, 6 switches and 5 ICs. It belongs with the STM32 boards of this library.
Project type: KiCAD
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3, R4, R5, R6, R7, R8, R9, R13 |
| 4 | 10u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1, C2, C3, C8 |
| 4 | Conn_01x01_Male | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J6, J8, J10, J15 |
| 4 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5, J9, J12, J16 |
| 4 | MountingHole | MountingHole:MountingHole_3.5mm | MH1, MH2, MH3, MH4 |
| 4 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1, SW2, SW3, SW4 |
| 3 | 100n | Capacitor_THT:C_Disc_D6.0mm_W2.5mm_P5.00mm | C9, C10, C11 |
| 3 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R10, R11, R12 |
| 3 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J11, J13, J14 |
| 2 | 20p | Capacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mm | C5, C6 |
| 2 | OLED | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2, J17 |
| 1 | 100u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C7 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R15 |
| 1 | 10n | Capacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mm | C4 |
| 1 | 3M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | AD623AN | Package_DIP:DIP-8_W7.62mm_LongPads | U1 |
| 1 | AP1117-33 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | Crystal | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | GND | Connector_Wire:SolderWirePad_1x01_Drill1.5mm | J18 |
| 1 | ICL7660 | Package_DIP:DIP-8_W7.62mm_LongPads | U2 |
| 1 | L_Small | Inductor_THT:L_Axial_L5.3mm_D2.2mm_P7.62mm_Horizontal_Vishay_IM-1 | L1 |
| 1 | POWER | Button_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_Angled | SW5 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW6 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | VBAT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J19 |
| 1 | XXX | Package_DIP:DIP-8_W7.62mm_LongPads | U5 |
| 1 | n/a | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R14 |
| 1 | power | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | tip | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J3 |
The 62 most common of 63 parts.

Pai-88/emg-robotic-hand
Single-channel surface-EMG front end (AD623 + driven-right-leg) on a Raspberry Pi Pico. Board fabricated and telemetry verified on hardware; analog front end and on-body EMG still in bring-up.

ninkaninus/TeamTurboTurtle
This is the repository of Team Turbo Turtle. A group made for the second semester project in robotics technology at Southern University Of Denmark.

TallesSantosCUBoulder/ECEN4532_DSPLab_Spring2026_ECG_Project
This signal of the heartbeat, in the form of the "PQRST" complex as seen with Figure 1, is what needs to be detected in order to find important information about a patient's heart.

GadgetReboot/Phone_SLIM
POTS Telephone Subscriber Line Interface Module

BojanSof/BluePillWaveGen
DDS function generator build around STM32 BluePill board

tvlad1234/osillyscope
Low cost, low part count CH32V003-based oscilloscope

SamsungSLAV/muxpi
MuxPi is an open hardware and open software board which was designed to aid in automating tasks on physical devices.

It measures 190 × 30 mm and has 2 copper layers, 1.6 mm thick.
63 parts, built around the AD623AN and ICL7660N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the pondahai/oscilloscopen repository on GitHub, at the commit this page was made from: the board is hardware/osilloscopen.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask pondahai before reusing the design.