2 layers41.7 × 9.7 mm
TriggerBoard Citrus
plants-tech/Zinnia
fork of a fork of phob 2.x (Phob 2.x Official -> PhloraGCC -> Zinnia)
7 parts2CERN-OHL-S-2.0
2 layers125.4 × 84.5 mm
Zinnia2 0 5
plants-tech/Zinnia2fork of a fork of phob 2.x (Phob 2.x Official -> PhloraGCC -> Zinnia)
- Size
- 125.4 × 84.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 113
- Nets
- 81
- Pads
- 426
- Tracks, vias
- 1,030, 134
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 27 Apr 2023
- Updated
- 6 Mar 2025
Overview
Zinnia2 0 5 is an open-source printed circuit board by plants-tech, from the plants-tech/Zinnia repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 125.4 × 84.5 mm with 113 parts on 81 nets, routed with 1,030 tracks and 134 vias.
It is built around the RP2040, MCP3002-I/P and W25Q128JVSIQ, with the USBLC6-2P6, AMS1117-3.3 and CUS10S30,H3F among its other parts. Its parts include 26 capacitors, 23 resistors, 14 switches, 13 ICs and 9 connectors. It belongs with the RP2040 boards of this library.
Main components
6
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
MCP3002-I/P
PDIP-8-40℃~+85℃ 10 1LSB 2 2.7V~5.5V 200kHz SPI PDIP-8 Analog to Digital Converters (ADC) ROHSMicrochip TechnologyAnalog To Digital Converters (ADC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
CUS10S30,H3F
SC-76(SOD-323)1 Independent 1A 230mV@100mA 30V 500uA@30V 5A SC-76(SOD-323) Schottky Diodes ROHSToshibaSchottky Diodes
README
README.mdZinniaGCC
fork of a fork of phob 2.x (Phob 2.x Official -> PhloraGCC -> ZinniaGCC)
RIP Jack Plants
Changes
- USB D+/D- Pad Alignment with Model U GCC v2
- Left Z implementation via its own pin; GPIO12
- Start Pad edit; now in style of D-Pad
- B3f tactile switch thru-holes on ABXY pads
- Omron D2LS alignment thru-holes on ABXY pads (experimental)
- Revision of both Analog and C-Stick footprints; removal of t1/t2 thru-holes, conversion of t3 screw-holes from copper-lined pads to non-conductive thru-holes (screws work more effectively, stickbox "wobble" eliminated slightly)
Images
Front
Back
License
Parts
113| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C17, C19, C20, C22, C24, C25, C26, C27, C28, C29, C30, C31, C32 |
| 6 | 0.047u | PhobGCC_2_0_0_footprints:C_0603_HandSoldering | C3, C4, C5, C6, C7, C8 |
| 5 | 180 | PhobGCC_2_0_0_footprints:R_0402_1005Metric | R1, R2, R7, R8, R9 |
| 4 | 2k | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R6 |
| 4 | 316 | PhobGCC_2_0_0_footprints:R_0402_1005Metric | R10, R19, R24, R25 |
| 4 | DRV5055A2xDBZxQ1 | PhobGCC_2_0_0_footprints:SOT-23 | U4, U9, U10, U11 |
| 3 | 10k | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R14, R15 |
| 2 | 1.8mm | PhobGCC_2_0_0_footprints:MountingHole_1.8mm | H5, H6 |
| 2 | 100R | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R12 |
| 2 | 10u | PhobGCC_2_0_0_footprints:C_0805_2012Metric | C16, C18 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R16, R18 |
| 2 | 1u | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C21, C23 |
| 2 | 2.2mm | PhobGCC_2_0_0_footprints:MountingHole_2.2mm | H8, H9 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R20, R21 |
| 2 | 27p | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C14, C15 |
| 2 | 2mm | PhobGCC_2_0_0_footprints:MountingHole_2.0mm | H3, H4 |
| 2 | CUS10S30,H3F | Diode_SMD:D_SOD-323 | D1, D5 |
| 2 | Conn_01x02 | PhobGCC_2_0_0_footprints:PinHeader_1x02_P2.00mm_Vertical | J2, J11 |
| 2 | Conn_01x06 | PhobGCC_2_0_0_footprints:PinSocket_1x06_P2.00mm_Vertical | J14, J15 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | MCP3002 | PhobGCC_2_0_0_footprints:SOIC-8_3.9x4.9mm_P1.27mm | U1, U3 |
| 2 | MountingHole | PhobGCC_2_0_0_footprints:MountingHole_2.0mm | H12, H13 |
| 2 | Q_NMOS_GSD | PhobGCC_2_0_0_footprints:SOT-23 | Q1, Q3 |
| 2 | R_POT_MountingPin | PhobGCC_2_0_0_footprints:GCC_Slider | RV1, RV2 |
| 2 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U12, U13 |
| 1 | |||
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17 |
| 1 | 2.4mm | PhobGCC_2_0_0_footprints:MountingHole_2.4mm | H7 |
| 1 | 47u | Capacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-T | C1 |
| 1 | 5.2mm | PhobGCC_2_0_0_footprints:MountingHole_5.2mm | H1 |
| 1 | A | PhobGCC_2_0_0_footprints:ABXY_Contact_Omron_Switch_b3F | SW1 |
| 1 | AMS1117-3.3 | PhobGCC_2_0_0_footprints:SOT-223-3_TabPin2 | U6 |
| 1 | B | Library:ABXY_Contact_Omron_Switch_b3F_v2 | SW2 |
| 1 | BOOTSEL | PhobGCC_2_0_0_footprints:SW_TS-1187A-B-A-B | S1 |
| 1 | Conn_01x01 | PhobGCC_2_0_0_footprints:PinHeader_1x01_P2.54mm_Vertical | J4 |
| 1 | Conn_01x06_Female | PhobGCC_2_0_0_footprints:GCC_Header_Straight_1x06_Pitch2.00mm | J1 |
| 1 | Crystal_GND24 | PhobGCC_2_0_0_footprints:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Ddown | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW12 |
| 1 | Dleft | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW9 |
| 1 | Dright | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW11 |
| 1 | Dup | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW10 |
| 1 | Fuse | PhobGCC_2_0_0_footprints:Fuse_1206_3216Metric | F1 |
| 1 | L | PhobGCC_2_0_0_footprints:Pin_Header_Straight_1x02_Pitch2.54mm | SW6 |
| 1 | M7C | Diode_SMD:D_SOD-123 | D2 |
| 1 | MountingHole | PhobGCC_2_0_0_footprints:MountingHole_5.2mm | H11 |
| 1 | MountingHole | PhobGCC_2_0_0_footprints:MountingHole_1.8mm | H10 |
| 1 | MouseBite | PhobGCC_2_0_0_footprints:breakaway-mousebites-double-v2-large | H15 |
| 1 | MouseBite | PhobGCC_2_0_0_footprints:breakaway-mousebites-double-v2-small | H14 |
| 1 | PinSocket_1x04_P2.00mm_Vertical | Connector_PinSocket_2.00mm:PinSocket_1x04_P2.00mm_Vertical | J6 |
| 1 | Q_PMOS_GDS | PhobGCC_2_0_0_footprints:SOT-23 | Q2 |
| 1 | R | PhobGCC_2_0_0_footprints:Pin_Header_Straight_1x02_Pitch2.54mm | SW7 |
| 1 | RP2040 | PhobGCC_2_0_0_footprints:RP2040-QFN-56 | U8 |
| 1 | Rumble | PhobGCC_2_0_0_footprints:rumble_pins | J5 |
| 1 | Slot | PhobGCC_2_0_0_footprints:Slot | H2 |
| 1 | Start | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW5 |
| 1 | Stickbox_Assembly_CStick | PhobGCC_2_0_0_footprints:GCC_Stickbox_Hall_Only | U5 |
| 1 | Stickbox_Assembly_Main | PhobGCC_2_0_0_footprints:GCC_Stickbox_Hall_Only | U2 |
| 1 | USB_B_Micro | phlob2000020000:USB_Micro-B_Amphenol_10118194_Horizontal | J9 |
| 1 | W25Q128JVS | PhobGCC_2_0_0_footprints:SOIC-8_5.23x5.23mm_P1.27mm | U7 |
| 1 | X | Library:ABXY_Contact_Omron_Switch_b3F_v2 | SW3 |
| 1 | Y | Library:ABXY_Contact_Omron_Switch_b3F_v2 | SW4 |
| 1 | Z | PhobGCC_2_0_0_footprints:Z_Switch_Edge_Omron | SW8 |
| 1 | ZL | PhobGCC_2_0_0_footprints:Z_Switch_Edge_Omron | SW8L |
More from plants-tech/Zinnia
2- 2 layers9.7 × 41.7 mm
TriggerBoard
plants-tech/Zinnia
fork of a fork of phob 2.x (Phob 2.x Official -> PhloraGCC -> Zinnia)
7 parts2CERN-OHL-S-2.0
Similar boards
- 2 layers125 × 79.4 mm
PHORI 2 0 5
Jwray0/phori_2
Forked from the https://github.com/PhobGCC/PhobGCCv2-HW Project
114 parts3CERN-OHL-S-2.0 - 2 layers125.5 × 90.3 mm
PhobGCC 2 0 0 proto 1
Naxdy/NaxGCC-HW
The main repository is located at git.naxdy.org. The GitHub mirror exists solely for the sake of discoverability and redundancy.
97 parts1CERN-OHL-S-2.0 - 2 layers119.5 × 60.3 mm
Jesnet proto 1
kje123/jesphob
A fork of the PhobGCC project, created for the JESNET Gamecube Controller
151 partsCERN-OHL-S-2.0 - 4 layers110.9 × 59.7 mm
- 2 layers110.9 × 59.5 mm
Procon gcc main pcb
ESCA47/thingamaPRO
Order at your own risk, even i fuck up too often. Maybe poke at me for help but for the most part you are on your own if you do decide to order these.
77 parts4CERN-OHL-S-2.0 - 4 layers60 × 56.1 mm
- 2 layers
- 2 layers100 × 100 mm
Open65
Maverick-Shark/X65_BigMiST
The X65 is an ultimate computer for everyone interested in the venerable 65-series of 8-bit and 16-bit CPUs, i.e. the 6502 and 65816.
195 partsMIT
Questions
How big is the Zinnia2 0 5 PCB?
It measures 125.4 × 84.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Zinnia2 0 5 use?
113 parts, built around the RP2040, MCP3002-I/P, W25Q128JVSIQ and USBLC6-2P6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Zinnia2 0 5 KiCad files?
From the plants-tech/Zinnia repository on GitHub, at the commit this page was made from: the board is PCB/KiCAD/Zinnia2_0_5.kicad_pcb and its schematic PCB/KiCAD/PhobLR/TriggerBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Zinnia2 0 5 design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).