2 layers125.4 × 84.5 mm
Zinnia2 0 5
plants-tech/Zinnia
fork of a fork of phob 2.x (Phob 2.x Official -> PhloraGCC -> Zinnia)
113 parts2CERN-OHL-S-2.0
2 layers125 × 79.4 mm
PHORI 2 0 5
Jwray0/phori_23Forked from the https://github.com/PhobGCC/PhobGCCv2-HW Project
- Size
- 125 × 79.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 114
- Nets
- 80
- Pads
- 400
- Tracks, vias
- 864, 136
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 23 Feb 2024
- Updated
- 20 Dec 2024
Overview
PHORI 2 0 5 is an open-source printed circuit board by Jwray0, from the Jwray0/phori_2 repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 125 × 79.4 mm with 114 parts on 80 nets, routed with 864 tracks and 136 vias.
It is built around the RP2040, MCP3002-I/P and W25Q128JVSIQ, with the USBLC6-2P6, AMS1117-3.3 and CUS10S30,H3F among its other parts. Its parts include 26 capacitors, 23 resistors, 15 switches, 13 ICs and 8 connectors. It belongs with the RP2040 boards of this library.
Main components
6
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
MCP3002-I/P
PDIP-8-40℃~+85℃ 10 1LSB 2 2.7V~5.5V 200kHz SPI PDIP-8 Analog to Digital Converters (ADC) ROHSMicrochip TechnologyAnalog To Digital Converters (ADC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
CUS10S30,H3F
SC-76(SOD-323)1 Independent 1A 230mV@100mA 30V 500uA@30V 5A SC-76(SOD-323) Schottky Diodes ROHSToshibaSchottky Diodes
README
README.mdPhobGCCv2-HW fork
Seperate repository for the hardware used in the phori v2
The PhobGCC v2.0 board is licensed under CERN Open Hardware Licence Version 2 - Strongly Reciprocal. This means that any changes made to the board should be made public and CHANGES.txt be updated to reflect said changes.
phori v2 is developed for the hori gamecube controller.
Parts
114| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C17, C19, C20, C22, C24, C25, C26, C27, C28, C29, C30, C31, C32 |
| 7 | 2.2mm | PhobGCC_Footprints:MountingHole_2.2mm | H8, H8, H8, H8, H8, H8, H8 |
| 6 | 0.047u | PhobGCC_2_0_0_footprints:C_0603_HandSoldering | C3, C4, C5, C6, C7, C8 |
| 5 | 180 | PhobGCC_2_0_0_footprints:R_0402_1005Metric | R1, R2, R7, R8, R9 |
| 4 | 2k | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R6 |
| 4 | 316 | PhobGCC_2_0_0_footprints:R_0402_1005Metric | R10, R19, R24, R25 |
| 4 | DRV5055Z3QDBZT | PhobGCC_2_0_0_footprints:SOT-23 | U3, U4, U10, U11 |
| 3 | 10k | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R14, R15 |
| 2 | 1.8mm | PhobGCC_2_0_0_footprints:MountingHole_1.8mm | H5, H6 |
| 2 | 100R | PhobGCC_2_0_0_footprints:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R12 |
| 2 | 10u | PhobGCC_2_0_0_footprints:C_0805_2012Metric | C16, C18 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R16, R18 |
| 2 | 1u | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C21, C23 |
| 2 | 2.4mm | PhobGCC_Footprints:MountingHole_2.4mm | H7, H7 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R20, R21 |
| 2 | 27p | PhobGCC_2_0_0_footprints:C_0402_1005Metric | C14, C15 |
| 2 | A | PhobGCC_2_0_0_footprints:ABXY_Contact_Omron_Switch_b3F | SW1, SW1 |
| 2 | CUS10S30,H3F | Diode_SMD:D_SOD-323 | D1, D5 |
| 2 | Dright | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW11, SW11 |
| 2 | Dup | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW10, SW10 |
| 2 | MCP3002 | PhobGCC_2_0_0_footprints:SOIC-8_3.9x4.9mm_P1.27mm | U1, U1 |
| 2 | MountingHole | PhobGCC_Footprints:MountingHole_2.0mm | H12, H13 |
| 2 | MountingHole | PhobGCC_Footprints:MountingHole_1.8mm | H10, H10 |
| 2 | MouseBite | PhobGCC_Footprints:breakaway-mousebites-double | H14, H15 |
| 2 | Q_NMOS_GSD | PhobGCC_2_0_0_footprints:SOT-23 | Q1, Q3 |
| 2 | R | PhobGCC_Footprints:Pin_Header_Straight_1x02_Pitch2.54mm | SW7, SW7 |
| 2 | R_POT_MountingPin | PhobGCC_2_0_0_footprints:GCC_Slider | RV1, RV2 |
| 2 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U12, U13 |
| 2 | Z | PhobGCC_Footprints:Z_Switch_Edge_Omron | SW8, SW8 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17 |
| 1 | 2.2mm | PhobGCC_2_0_0_footprints:MountingHole_2.2mm | H9 |
| 1 | 47u | Capacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-T | C1 |
| 1 | AMS1117-3.3 | PhobGCC_2_0_0_footprints:SOT-223-3_TabPin2 | U6 |
| 1 | B | Library:ABXY_Contact_Omron_Switch_b3F_v2 | SW2 |
| 1 | BOOTSEL | PhobGCC_2_0_0_footprints:SW_TS-1187A-B-A-B | S1 |
| 1 | Conn_01x01 | PhobGCC_2_0_0_footprints:PinHeader_1x01_P2.54mm_Vertical | J4 |
| 1 | Conn_01x02 | PhobGCC_2_0_0_footprints:PinHeader_1x02_P2.00mm_Vertical | J2 |
| 1 | Conn_01x04_Female | PhobGCC_Footprints:PinHeader_1x04_P2.00mm_Vertical | J2 |
| 1 | Conn_01x04_Male | PhobGCC_Footprints:PinHeader_1x04_P2.00mm_Vertical | J4 |
| 1 | Conn_01x06_Female | PhobGCC_2_0_0_footprints:GCC_Header_Straight_1x06_Pitch2.00mm | J1 |
| 1 | Crystal_GND24 | PhobGCC_2_0_0_footprints:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Fuse | PhobGCC_2_0_0_footprints:Fuse_1206_3216Metric | F1 |
| 1 | L | PhobGCC_Footprints:Pin_Header_Straight_1x02_Pitch2.54mm | SW6 |
| 1 | LOGO | LOGO | G*** |
| 1 | M7C | Diode_SMD:D_SOD-123 | D2 |
| 1 | PinSocket_1x04_P2.00mm_Vertical | Connector_PinSocket_2.00mm:PinSocket_1x04_P2.00mm_Vertical | J6 |
| 1 | Q_PMOS_GDS | PhobGCC_2_0_0_footprints:SOT-23 | Q2 |
| 1 | RP2040 | PhobGCC_2_0_0_footprints:RP2040-QFN-56 | U8 |
| 1 | Rumble | PhobGCC_2_0_0_footprints:rumble_pins | J5 |
| 1 | Start | PhobGCC_2_0_0_footprints:Dpad_Contact_TL3315NF_2 | SW5 |
| 1 | Stickbox_Assembly | PhobGCC_Footprints:GCC_Stickbox_Hall_Only | U5 |
| 1 | Stickbox_Assembly_Main | PhobGCC_2_0_0_footprints:GCC_Stickbox_Hall_Only | U2 |
| 1 | USB_B_Micro | phlob2000020000:USB_Micro-B_Amphenol_10118194_Horizontal | J9 |
| 1 | W25Q128JVS | PhobGCC_2_0_0_footprints:SOIC-8_5.23x5.23mm_P1.27mm | U7 |
| 1 | Y | Library:ABXY_Contact_Omron_Switch_b3F_v2 | SW4 |
Similar boards
- 2 layers125.5 × 90.3 mm
PhobGCC 2 0 0 proto 1
Naxdy/NaxGCC-HW
The main repository is located at git.naxdy.org. The GitHub mirror exists solely for the sake of discoverability and redundancy.
97 parts1CERN-OHL-S-2.0 - 2 layers119.5 × 60.3 mm
Jesnet proto 1
kje123/jesphob
A fork of the PhobGCC project, created for the JESNET Gamecube Controller
151 partsCERN-OHL-S-2.0 - 4 layers110.9 × 59.7 mm
- 2 layers110.9 × 59.5 mm
Procon gcc main pcb
ESCA47/thingamaPRO
Order at your own risk, even i fuck up too often. Maybe poke at me for help but for the most part you are on your own if you do decide to order these.
77 parts4CERN-OHL-S-2.0 - 4 layers60 × 56.1 mm
- 2 layers
- 2 layers100 × 100 mm
Open65
Maverick-Shark/X65_BigMiST
The X65 is an ultimate computer for everyone interested in the venerable 65-series of 8-bit and 16-bit CPUs, i.e. the 6502 and 65816.
195 partsMIT
Questions
How big is the PHORI 2 0 5 PCB?
It measures 125 × 79.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the PHORI 2 0 5 use?
114 parts, built around the RP2040, MCP3002-I/P, W25Q128JVSIQ and USBLC6-2P6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PHORI 2 0 5 KiCad files?
From the Jwray0/phori_2 repository on GitHub, at the commit this page was made from: the board is KICAD/PHORI_2_0_5.kicad_pcb and its schematic KICAD/PHORI_2_0_5.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PHORI 2 0 5 design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).