
DKWS PCB
danielkluka/Diploma-Thesis
Design of a Secure Data Transmission System in NB-IoT Environment

Kh gift hw is an open-source printed circuit board by phonght32, from the phonght32/kh-gift-hw repository on GitHub, published under the MIT licence. It is a 2-layer board of 89.3 × 55 mm with 69 parts on 91 nets, routed with 483 tracks and 241 vias.
It is built around the ESP32-WROVER, DHT11 and SX1308, with the IRLML0030, AMS1117-3.3 and DS1307Z+ among its other parts. Its parts include 21 resistors, 16 capacitors, 10 ICs, 8 diodes and 3 transistors. It belongs with the ESP32 boards of this library.

| Items | Specifications |
|---|---|
| Power supply | Pin LiPo 1 cell |
| Microcontroller | ESP32 |
| LEDs and Buttons | LED Charge LED Standby User push button |
| Dimensions | 89.4 x55 mm Screw hole 83.4 x 49 mm |




| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric | C4, C6, C7, C8, C13, C16 |
| 6 | 10uF | Capacitor_SMD:C_1210_3225Metric | C3, C5, C11, C12, C14, C15 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R5, R6, R7 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R11, R15, R16 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R2, R3, R10 |
| 3 | 330R | Resistor_SMD:R_0603_1608Metric | R13, R14, R21 |
| 2 | 100nF | Capacitor_SMD:C_1210_3225Metric | C1, C2 |
| 2 | 4K7 | Resistor_SMD:R_0603_1608Metric | R19, R20 |
| 2 | IRLML0030 | Package_TO_SOT_SMD:SOT-23 | U10, U12 |
| 2 | MMBT2222A | Package_TO_SOT_SMD:SOT-23 | Q4, Q5 |
| 2 | SW_Push | footprints:PushButton_6x6mm_SMD | SW1, SW2 |
| 2 | TBD | Resistor_SMD:R_0603_1608Metric | R17, R18 |
| 1 | 0.1H | Inductor_SMD:L_Coilcraft_XAL5030-XXX | L1 |
| 1 | 0.1uF | Capacitor_SMD:C_1210_3225Metric | C10 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 1.2k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 100R | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 32768 kHz | footprints:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U8 |
| 1 | Buzzer | Buzzer_Beeper:MagneticBuzzer_Kobitone_254-EMB84Q-RO | BZ1 |
| 1 | CP2102N-Axx-xQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U6 |
| 1 | Cell | Footprint-Kicad:BAT_CR1220_Holder | BT2 |
| 1 | Conn_01x14 | footprints:ili9341_3.2inch | J2 |
| 1 | DHT11 | footprints:SNR4-2.54-15.5X12.0X5.5MM | U1 |
| 1 | DS1307Z+ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U9 |
| 1 | DW01A | Package_TO_SOT_SMD:TSOT-23-6 | U4 |
| 1 | ESP32-WROVER | Footprint-Kicad:ESP32-WROVER | U2 |
| 1 | GREEN | Footprint-Kicad:Connector_ZH_1x02_P1.25mm_Horizontal | D5 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | MMBT5550 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | NC | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | PinLipo | footprints:JST_EH_S2B-EH_1x02_P2.5mm_Horizontal | BT1 |
| 1 | Potentiometer | Footprint-Kicad:Connector_ZH_1x03_P1.25mm_Horizontal | RV1 |
| 1 | RED | Footprint-Kicad:Connector_ZH_1x02_P1.25mm_Horizontal | D6 |
| 1 | RED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | RX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D8 |
| 1 | SS24 | Diode_SMD:D_SMA | D3 |
| 1 | SW_Push | Footprint-Kicad:Connector_ZH_1x02_P1.25mm_Horizontal | SW3 |
| 1 | SX1308 | Package_TO_SOT_SMD:TSOT-23-6 | U7 |
| 1 | TP4056 | footprints:SOP127P600X175-9N | U3 |
| 1 | TX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D7 |
| 1 | USB | footprints:JST_EH_S4B-EH_1x04_P2.5mm_Horizontal | J3 |
| 1 | YELLOW | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |

danielkluka/Diploma-Thesis
Design of a Secure Data Transmission System in NB-IoT Environment

NGOQUOC98/ESP32_MODBUS_PCB_MASTER
This project was in development phase - we will remove this remark after release

TilenTinta/Greenhouse_LoRa_Node
An open-source monitoring system designed for use in greenhouses, orchards or other agricultural environments


vmfachini/Lumibot
Desenvolvimento de um Hardware Livre, com uso de energia limpa, baseado no micro:bit para criar robôs móveis acessíveis, promovendo ensino de robótica, pensamento computacional e sustentabilidade no Brasil.

elektricM/nwpi-pcb
NWPi custom PCB - Power module for Raspberry Pi Zero inside NumWorks calculator

HarryVienna/Slave-clock-controller-with-ESP32-C3-OLED-and-DRV8871
A compact, affordable, and robust controller for analog slave clocks and flip clocks (e.g., Bodet), based on the ESP32-C3 microcontroller and the DRV8871 H-Bridge driver.

It measures 89.3 × 55 mm and has 2 copper layers, 1.6 mm thick.
69 parts, built around the ESP32-WROVER, DHT11, SX1308 and IRLML0030. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the phonght32/kh-gift-hw repository on GitHub, at the commit this page was made from: the board is kh-gift-hw.kicad_pcb and its schematic kh-gift-hw.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).