4 layers115.5 × 96.2 mm
Closed deck x4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
245 parts19
4 layers98.8 × 69.8 mm
SparkGapX4
OpenLogicEFI/Hardware19Hardware is based off an open source project called Speeduino by Josh Stewart.
- Size
- 98.8 × 69.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 166
- Nets
- 176
- Pads
- 550
- Tracks, vias
- 899, 402
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 29 Mar 2020
- Updated
- 19 Oct 2026
Overview
SparkGapX4 is an open-source printed circuit board by OpenLogicEFI, from the OpenLogicEFI/Hardware repository on GitHub. It is a 4-layer board of 98.8 × 69.8 mm with 166 parts on 176 nets, routed with 899 tracks and 402 vias.
It is built around the IXDN602SIATR, CH340N and KP234XTMA1, with the SRV05-4, 74LVC1G157GW,125 and ULN2003ADRG among its other parts. Its parts include 63 resistors, 46 capacitors, 12 ICs, 11 transistors and 9 diodes.
Main components
12
IXDN602SIATR
SOIC-8-40℃~+125℃ 10uA 2 2A 2A 4.5V~35V 6.5ns 7.5ns IGBT、MOSFET Low Side SOIC-8 Gate Drivers ROHSLittelfuse/IXYSGate Drivers
CH340N
SOP-8-20℃~+70℃ 1 2Mbps 3.3V、5V USB 2.0 USB to serial SOP-8 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
KP234XTMA1
SMD-8P-40℃~+125℃ 1.5Kpa 1ms 4.5V~5.5V 40Kpa~1.15bar Temperature Sensor Yes SMD-8P Pressure Sensors ROHSInfineon TechnologiesPressure Sensors
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
74LVC1G157GW,125
SOT-363-6-40℃~+125℃ 1.65V~5.5V 2/1 32mA 32mA 4uA 5ns@5.5V,50pF 74LVC Multiplexer Power-off protection、Level shifting Single Supply SOT-363-6 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches, Multiplexers, Decoders
ULN2003ADRG
SOP-16SOP-16 Darlington Transistor Arrays ROHSQNHDarlington Transistor Arrays
2N7002K
SOT-23-55℃~+150℃ 1 N-channel 1.2Ω@10V、1.4Ω@5V 1.6V 2.9pF 300pC@4.5V 30pF 380mA 4.2pF 540mW 60V SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETsAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsBAT54S
SOT-231 Pair Series Connection 1V@100mA 200mA 2uA@25V 30V 600mA SOT-23 Schottky Diodes ROHSMDDSchottky Diodes
DSK210
SOD-123FLSchottky Diodeshongjiacheng
1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky Diodes
MX23A40NF1
插件2 Automotive Connector Socket Right Angle 插件 Automobile Connectors ROHSJAE ElectronicsAutomobile Connectors
README
README.mdOpenLogicEFI
Formerly: DetonationEMS
OpenLogicEFI ECU's are based off an open source project called Speeduino by Josh Stewart. Currently all released boards use official Speeduino firmware. In TunerStudio set to "Board Layout" to "Speeduino 0.4"
License
All designs are released under the TAPR Open Hardware License v1.0
Documentation
-
The Official Speeduino Manual, documents and discord are the best places to start.
Parts
166| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C12, C14, C17, C18, C21, C23, C25, C26, C27, C28, C30, C34, C36, C37, C38 +6 |
| 18 | 470r | Resistor_SMD:R_0402_1005Metric | R13, R15, R16, R38, R39, R40, R41, R42, R49, R50, R52, R53, R54, R55, R56, R61 +2 |
| 13 | 51k | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8, R9, R10, R14, R22, R26, R27, R28, R37, R51 |
| 11 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R11, R20, R21, R23, R24, R25, R43, R44, R45, R47 |
| 11 | 220nF | Capacitor_SMD:C_0402_1005Metric | C3, C11, C15, C19, C20, C22, C24, C29, C31, C33, C35 |
| 5 | 2.2k | Resistor_SMD:R_0402_1005Metric | R2, R29, R30, R31, R32 |
| 4 | 22 | Resistor_SMD:R_0805_2012Metric | R33, R34, R35, R36 |
| 4 | 2N7002K | Package_TO_SOT_SMD:SOT-23 | Q1, Q9, Q10, Q11 |
| 4 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C4, C6, C16, C47 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | IGN1, IGN2, IGN3, IGN4 |
| 4 | STP75N04Z | Package_TO_SOT_THT:TO-220-3_Vertical | Q3, Q4, Q5, Q6 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R18, R19, R48 |
| 3 | 10nF | Capacitor_SMD:C_0402_1005Metric | C2, C8, C9 |
| 3 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q2, Q7, Q8 |
| 3 | BAT54S | Package_TO_SOT_SMD:SOT-23 | D14, D15, D16 |
| 3 | DSK210 | Diode_SMD:D_SOD-123F | D5, D6, D7 |
| 3 | FET Bypass | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2, JP5 |
| 3 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U5, U6, U8 |
| 3 | TestPoint | Detonation:TestPoint_THT_D0.6mm_Drill0.3mm | TP1, TP2, TP4 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C41, C48 |
| 2 | 2.49k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R59, R60 |
| 2 | 2k | Resistor_SMD:R_0402_1005Metric | R12, R46 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R57, R58 |
| 2 | Conn_01x04 | Detonation:1X4-PROTO-NoSilk | J3, J4 |
| 2 | DIRECT/VR | Detonation:1x03-Proto | JP3, JP4 |
| 2 | IXDN602SIATR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3, U4 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C44 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 120r | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | 1N5819WS | Diode_SMD:D_SOD-323 | D9 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 3.9k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 470nF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 47pF | Capacitor_SMD:C_0402_1005Metric | C32 |
| 1 | 74LVC1G157GW,125 | Detonation:SOP65P210X110-6N | IC2 |
| 1 | 7805 | Detonation:TO-220-3_Vertical_SmallCrtYrd | IC1 |
| 1 | CH340N | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | DRV8825_Module | Detonation:DVR8825-Labeled-Front | A1 |
| 1 | Jumper_3_Open | Detonation:1x03-Proto | JP8 |
| 1 | KP234XTMA1 | Detonation:KP234-Handsoldering | IC3 |
| 1 | LOGO | Detonation-Logos:DCWerx-19mm | G*** |
| 1 | LOGO | Detonation-Logos:logic_8 | G*** |
| 1 | Logo_Open_Hardware_Small | Symbol:OSHW-Logo2_7.3x6mm_SilkScreen | G2 |
| 1 | Logo_Open_Hardware_Small | Detonation-Logos:SpeeduinoCompatible-14mm | G1 |
| 1 | MPXHZ6400 | Detonation:MPXHxxx_Handsoldering | IC4 |
| 1 | MX23A40NF1 | Detonation:MX23A40NF1 | J1 |
| 1 | Mega_Pro_VinPinsUnpopulated | Detonation:Arduino_Mega_Mini_2560_SmallCrtYd_NoVin | U2 |
| 1 | Reset Control | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | S1 |
| 1 | SMBJ16A | Diode_SMD:D_SMB | D1 |
| 1 | SS14 | Diode_SMD:D_SMA | D2 |
| 1 | SolderJumper_3_Open | Detonation:SolderJumper-3-OPEN | JP6 |
| 1 | ULN2003ADR | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | USB-S0 | Connector_JST:JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J5 |
| 1 | VR_Header | Detonation:Socket_VRConditioner_Corrected | J2 |
More from OpenLogicEFI/Hardware
12- 2 layers115.5 × 96.2 mm
Closed deck x4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
223 parts19 - 2 layers98.8 × 69.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
167 parts19 - 2 layers100 × 99.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
166 parts19 - 2 layers98.8 × 69.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
159 parts19 - 2 layers100 × 100 mm
1.3e
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
157 parts19 - 2 layers100 × 99.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
152 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
142 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
141 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
136 parts19 - 2 layers98.2 × 53.3 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
104 parts19 - 2 layers98.2 × 53.3 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
102 parts19
Similar boards
- 4 layers80 × 60 mm
Kcell faker
karlp/kcell-faker
fake a load cell, for testing functional behaviour with changing loads.
75 parts - 4 layers110 × 90 mm
FilMachine Mainboard
yesnoj/FilMachine_Reworked
FilMachine is an automated film processing machine designed for photographic film development. It handles the entire process: chemical baths, water rinses, temperature regulation, and motor-driven film agitation — all…
205 parts - 2 layers100.3 × 99.3 mm
Miatuino
Maverick765/miatuino
まずはアクセルを完全に戻した状態で[Closed throttle ADC Count]の右の[Get Current]をクリックして、スロットル全閉時の値を取得します。 次に、アクセルを完全に踏み込んだ状態で[Full throttle ADC Count]の右の[Get Current]をクリックして、スロットル前回時の値を取得します。 完了したら[Accept]をクリックします。
121 parts1GPL-2.0 - 4 layers114.3 × 63.5 mm
- 2 layers80 × 99.8 mm
- 2 layers100.6 × 131 mm
Habitat V5
machadoleonardo94/HabitatControl-hardware
Hardware files for HabitatControl, designed on DipTrace
161 parts1 - 8 layers140 × 314.2 mm
- 4 layers40 × 55 mm
CopterCat cm4
matveylapin/CopterCat_cm4
Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.
164 parts3Apache-2.0
Questions
How big is the SparkGapX4 PCB?
It measures 98.8 × 69.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the SparkGapX4 use?
166 parts, built around the IXDN602SIATR, CH340N, KP234XTMA1 and SRV05-4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SparkGapX4 KiCad files?
From the OpenLogicEFI/Hardware repository on GitHub, at the commit this page was made from: the board is Engine Managment/Spark Gap/Spark Gap X4/RevC2/SparkGapX4.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the SparkGapX4 design in my own project?
Its repository states no licence, so its author keeps all rights: ask OpenLogicEFI before reusing the design.