

Openbms load
OpenBMS 600W resistive load (dissipative) hardware [schematic] [PCB layout]
- Size
- 327.5 × 219.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 113
- Nets
- 45
- Pads
- 220
- Tracks, vias
- 252, 13
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 16 Apr 2026
- Updated
- 5 Jun 2026
Overview
Openbms load is an open-source printed circuit board by open-batt, from the open-batt/openbms-test-bench-hardware repository on GitHub, published under the MIT licence. It is a 2-layer board of 327.5 × 219.5 mm with 113 parts on 45 nets, routed with 252 tracks and 13 vias.
It is built around the LMZM23600SILR. Its parts include 29 connectors, 21 fuses, 20 resistors, 6 capacitors and 4 diodes. It belongs with the power boards of this library.
Main components
1README
README.mdOpenBMS Test Bench
OpenBMS Test Bench is a hardware design of a resistive load used for battery discharging. Its main purpose is testing the battery management system (BMS) during charge and discharge cycles.
How OpenBMS Test Bench fits into system?
Battery system consists of:
- Li-ion/Li-Po battery — your custom 2- to 7-cell battery
- OpenBMS — battery management system that handles fuel gauging, cell balancing, learning algorithms, overcharge/overdischarge/overheat protection, and communication with chargers and microcontrollers
- Test Bench — a 600W dissipative resistive load for easier BMS development and testing
- Host — I2C/CAN interfaces, wake-up signal, can be a microcontroller, computer, etc.
- Charger — your custom charger, usually a CC/CV charger adjusted to your battery voltage and current
- OpenBMS Studio — a PC software for configuring and monitoring the BMS, visualizing data, and updating firmware using UART communication
Features
- 🔥 Twenty 25-ohm 50W resistors to dissipate up to 600W
- 🔛 Jumpers / 5A fuse - each resistor has jumper/fuse to enable it or disable it - this way total load resistance can be adjusted from 1 to 20 ohms
- 🔌 Male XT60 connector for BMS (battery) connection
- 🔌 Female XT60 connector for charger connection
- 🔄 Tri state switch:
- 1 - Battery discharging - energy flows from battery to load (resistors)
- 2 - Battery charging - energy flows from charger to battery (resistors are bypassed and not used)
- 3 - Idling - battery is neither charging nor discharging
- 💨 Six fans to blow heat from resistors - speed adjustable by potentiometer
- 🟢 Green LED to indicate that charger is present
- 🔴 Red LED to indicate that battery is discharging
Overview
The OpenBMS Test Bench, a 600W resistive load, is a purpose-built battery testing board designed to work alongside the OpenBMS system.
It carries twenty 25Ω 50W wirewound resistors arranged across the board, capable of dissipating up to 600W of power. Each resistor is individually switchable via a jumper and protected by a 5A fuse, allowing the total load resistance to be adjusted between 1 and 20 ohms.
Six cooling fans keep the resistors from overheating, with speed controlled by an onboard potentiometer.
Two XT60 connectors handle battery and charger connections, and a three-position switch selects between discharging (energy flows from battery into the resistors), charging (charger feeds the battery directly, bypassing the resistors), and idle mode.
A green LED signals charger presence and a red LED indicates active discharging.
❤️ Funding
This project is funded through NGI0 Commons Fund, a fund established by NLnet with financial support from the European Commission's Next Generation Internet program.
We are very grateful to the NLnet team for helping us on our path, and we encourage you too to apply and get funds to build your project! 🚀 Learn more at the NLnet project page.
License
OpenBMS Test Bench is licensed under CERN OHL-S v2 license.
Check openbatt.dev for more!
Parts
113| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 5A Fuse | custom_library:0297005.WXNV | J1, J2, J3, J4, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21 +5 |
| 21 | Fuse housing | custom_library:3568 | F1, F2, F3, F4, F10, F11, F12, F13, F14, F15, F16, F17, F18, F19, F20, F21 +5 |
| 20 | 25R 50W | custom_library:L50J25RE | R1, R2, R3, R4, R5, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20 +4 |
| 12 | L mounting bracket | custom_library:633 | B1, B2, B3, B4, B5, B6, B7, B8, B9, B10, B11, B12 |
| 12 | Standoff M3 10mm | custom_library:24433 | H1, H2, H3, H4, H5, H6, H7, H8, H9, H10, H11, H12 |
| 6 | Fan 50mm | custom_library:fan_MF50101V1-1000U-A99 | M1, M2, M3, M4, M5, M6 |
| 6 | JST connector | custom_library:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | P1, P2, P3, P4, P5, P6 |
| 4 | 10u | Capacitor_SMD:C_1206_3216Metric | C1, C2, C4, C5 |
| 2 | 100n | Capacitor_SMD:C_0402_1005Metric | C3, C6 |
| 2 | LED driver | custom_library:AL5809-15P1-7 | D3, D4 |
| 1 | 10k pot | custom_library:TC33X2503E | POT1 |
| 1 | Green LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LMZM23600SILR | custom_library:LMZM23600SILR | U1 |
| 1 | Red LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | Switch | custom_library:VRS-3-Q3PSI-19KNN-0-M2 | SW1 |
| 1 | XT60PW-F connector | custom_library:AMASS_XT60PW-F_1x02_P7.20mm_Horizontal | P8 |
| 1 | XT60PW-M connector | custom_library:AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | P7 |
Similar boards
- 2 layers23.2 × 50.6 mm

- 4 layers75 × 75 mm

USAN r0
alu-source/open_USAN
This project documents the software and hardware of an ultrasonic anemometer, created in cooperation between FH Aachen and DLR Göttingen
262 parts1 - 2 layers122.5 × 87.6 mm

- 2 layers243.2 × 106 mm

- 2 layers294 × 100 mm

- 2 layers81.1 × 128.5 mm

- 2 layers247.1 × 121.4 mm

- 2 layers120 × 80 mm

Rx72t 100 pga usb
hirakuni45/RX
Renesas RX Microcontroller, C++ framework, Library, Sample
113 parts86BSD-3-Clause
Questions
How big is the Openbms load PCB?
It measures 327.5 × 219.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Openbms load use?
113 parts, built around the LMZM23600SILR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Openbms load KiCad files?
From the open-batt/openbms-test-bench-hardware repository on GitHub, at the commit this page was made from: the board is openbms-load/openbms-load.kicad_pcb and its schematic openbms-load/connectors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Openbms load design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
