Skip to the content
2 layers85 × 56 mmPihat, the printed circuit board in 3D

An open source codec2 based handheld digital radio for VHF/UHF amateur bands

Size
85 × 56 mm
Copper layers
2
Thickness
0.6 mm
Parts
49
Nets
35
Pads
190
Tracks, vias
580, 214
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
12 Oct 2016
Updated
8 May 2017

Overview

Pihat is an open-source printed circuit board by omc8db, from the omc8db/DigitalVoice repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 85 × 56 mm with 49 parts on 35 nets, routed with 580 tracks and 214 vias.

It is built around the TPS61027DRC, MCP73833 and SI4464DY. Its parts include 17 capacitors, 11 resistors, 6 ICs, 6 inductors and 3 diodes.

Main components

3

README

hardware/PiHat_Final/README.md

% RPi B+ Hat

Raspberry Pi B+ Hat

Expansion Board

This is a project template for a Raspberry Pi B+ Hat.

This base project includes a PCB edge defined according to this specification. Both a thru-hole and a surface mount connector are provided, along with a different PCB edge for each. Just keep the PCB edge and connector type that you're using for your design and delete the others.

The component footprints used in this template are here.

The board outline looks like this:

Using the Template

To use the Raspberry Pi Hat template with the through-hole connector, do the following:

  1. Open the schematic. Remove the SMD connector, J1.
  2. Generate the schematic netlist.
  3. Generate the .cmp file. (The J2 connector will be the only component in it.)
  4. Open the PCB. Hover your mouse over the connector and hit e to edit it. Select the J1 SMD connector. In the Move and Place section of the Footprint Properties window, select the Free radio button. Then click OK. The SMD connector should now be unlocked so it can be removed.
  5. Read in the netlist from the schematic. In the Extra Footprints section of the Netlist dialog window, select the Delete radio button. Then click Read Current Netlist. The J1 SMD connector should disappear. Then click Close.
  6. Finally, delete the upper two arcs and the edge of the board outline.

To use the Raspberry Pi Hat template with the SMD connector, do the following:

  1. Open the schematic. Remove the through-hole connector, J2.
  2. Generate the schematic netlist.
  3. Generate the .cmp file. (The J1 connector will be the only component in it.)
  4. Open the PCB. Hover your mouse over the connector and hit e to edit it. Select the J2 through-hole connector. In the Move and Place section of the Footprint Properties window, select the Free radio button. Then click OK. The through-hole connector should now be unlocked so it can be removed.
  5. Read in the netlist from the schematic. In the Extra Footprints section of the Netlist dialog window, select the Delete radio button. Then click Read Current Netlist. The J2 through-hole connector should disappear. Then click Close.
  6. Finally, delete the lower two arcs and the edge of the board outline.

(c)2015 XESS Corp.

Parts

49
QtyValueFootprintReferences
810uFCapacitors_SMD:C_0805C1, C2, C3, C9, C10, C13, C14, C15
6CCapacitors_SMD:C_0805C4, C5, C6, C7, C8, C11
51KResistors_SMD:R_0805R1, R2, R3, R4, R5
5RResistors_SMD:R_0603R7, R8, R9, R10, R11
4L_SmallResistors_SMD:R_0805L1, L2, L3, L4
3LEDLEDs:LED_0805D1, D2, D3
210nFCapacitors_SMD:C_0805C16, C17
2SMA_Edge_MountRF BW Filter:SMA_Edge_MountU5, U6
110KResistors_SMD:R_0805TH1
1150KResistors_SMD:R_0603R6
11uHinductor:BOURNES_SRN4018L6
130MHzCrystals:Crystal_SMD_5032_4PadsX1
147uFCapacitors_SMD:c_elec_5x5.3C12
16.8uHinductor:BOURNES_SRN4018L5
1BATTPin_Headers:Pin_Header_Straight_1x02P3
1CONN_13X2Pin_Headers:Pin_Header_Straight_2x13P1
1MCP73833Housings_DFN_QFN:DFN-10-1EP_3x3mm_Pitch0.5mmU1
1POTPotentiometers:Potentiometer_Bourns_3296W_3-8Zoll_Inline_ScrewUpRV1
1SC189Housings_DFN_QFN:DFN-6-1EP_2x2mm_Pitch0.5mmU3
1Si4464Housings_DFN_QFN:QFN-20-1EP_4x4mm_Pitch0.5mmU4
1TPS61027Housings_DFN_QFN:DFN-10-1EP_3x3mm_Pitch0.5mmU2
1USB_OTGConnect:USB_Micro-BP2

More from omc8db/DigitalVoice

4
  • 2 layers65 × 56 mmRPi Hat, the printed circuit board in 3D

    RPi Hat

    omc8db/DigitalVoice

    An open source codec2 based handheld digital radio for VHF/UHF amateur bands

    76 parts1Apache-2.0
  • 2 layers90 × 39.1 mmPWRBRD, the printed circuit board in 3D

    PWRBRD

    omc8db/DigitalVoice

    An open source codec2 based handheld digital radio for VHF/UHF amateur bands

    61 parts1Apache-2.0
  • 2 layers65 × 56 mmRPi Hat, the printed circuit board in 3D

    RPi Hat

    omc8db/DigitalVoice

    An open source codec2 based handheld digital radio for VHF/UHF amateur bands

    46 parts1Apache-2.0
  • 2 layers52 × 12 mmRF BW Filter, the printed circuit board in 3D

    RF BW Filter

    omc8db/DigitalVoice

    An open source codec2 based handheld digital radio for VHF/UHF amateur bands

    7 parts1Apache-2.0

Similar boards

  • 2 layers48 × 78.2 mmAIS Receiver, the printed circuit board in 3D

    AIS Receiver

    cmbahadir/AIS-Receiver

    Homemade AIS Receiver with ESP32

    73 parts11
  • 2 layers85 × 54 mmAether, the printed circuit board in 3D

    Aether

    AerodyneLabs/Aether

    High-altitude balloon pico-tracker

    82 parts2
  • 4 layers36 × 50.2 mmRacer, the printed circuit board in 3D

    Racer

    StuckAtPrototype/Racer

    These are structured into their own files. I could have used submodules, but decided against it.

    83 parts3.8kApache-2.0
  • 4 layers74.7 × 30 mmController, the printed circuit board in 3D

    Controller

    StuckAtPrototype/Thumbtroller

    77 parts305
  • 4 layers49 × 74.9 mmPCB business card, the printed circuit board in 3D

    PCB business card

    StuckAtPrototype/PCB_business_card_remake

    A custom PCB based "business" card that lets you play a version of Flappy Bird.

    311 parts132Apache-2.0
  • 4 layers536.5 × 385.7 mmDC27-badge, the printed circuit board in 3D

    DC27-badge

    netik/dc27_badge

    Defcon 27 "DaBomb!" badge.

    141 parts30Apache-2.0
  • 6 layers50 × 85 mmRusty tracker, the printed circuit board in 3D

    Rusty tracker

    korken89/rusty-tracker

    There are 2 versions of the board, based on:

    181 parts14
  • 6 layers131 × 80 mmOpenHardwareHolterMonitor, the printed circuit board in 3D

    OpenHardwareHolterMonitor

    OpenElectronicsLab/OpenHardwareHolterMonitor

    OpenHardware ECG Holter Monitor

    165 parts9GPL-3.0

Questions

How big is the Pihat PCB?

It measures 85 × 56 mm and has 2 copper layers, 0.6 mm thick.

What parts does the Pihat use?

49 parts, built around the TPS61027DRC, MCP73833 and SI4464DY. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pihat KiCad files?

From the omc8db/DigitalVoice repository on GitHub, at the commit this page was made from: the board is hardware/pihat/pihat.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pihat design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).