Skip to the content
4 layers47.5 × 26 mmVoltmeterFrontEnd, the printed circuit board in 3D

VoltmeterFrontEnd

oihdesigns/Micro-DMM2

A small, open hardware DMM

Size
47.5 × 26 mm
Copper layers
4
Thickness
1.6 mm
Parts
27
Nets
14
Pads
68
Tracks, vias
102, 13
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
22 Jun 2025
Updated
1 Nov 2026

Overview

VoltmeterFrontEnd is an open-source printed circuit board by oihdesigns, from the oihdesigns/Micro-DMM repository on GitHub. It is a 4-layer board of 47.5 × 26 mm with 27 parts on 14 nets, routed with 102 tracks and 13 vias.

It is built around the MMBT3904. Its parts include 10 resistors, 3 capacitors, 3 diodes, 2 ICs and 2 transistors.

Main components

1

README

README.md

20250623_204616_470_1DXII copy

Update Late August '25:

I've recently started a new job. It's great, but has longer hours than my previous job. This will negatively affect the amount of time I put into this project...

Micro-DMM

This is the PCB design and code for a 4.5 digit DMM/ instrumentation module. It is designed and written primairly for Arduino-style development boards.

I've developed this DMM in my work testing and troubleshooting electronics to make my life easier.

I've had Deep-Wiki index my documentation. It did a mostly okay job. You can read its summary here: Ask DeepWiki

20250623_205912_480_1DXII copy

The main features are:

  • The most recent designs have open-lead detection in voltmeter mode. I believe this makes it the first voltmeter in exisitance that can automatically, safely, and positively tell the difference between "there is low impedance between these points" vs "current does not and can not flow between these two points." Please see the white paper for details.
  • Using keyboard emulation to directly type values into a computer for me. (Extremely useful when troubleshooting a populated PCB - you can quickly ohm out both the problem board and a good one directly into Excel to look for different impedances between given contacts.)
  • Very sensitive low-resistance readings (accurate to better than 0.01 Ohms with proper lead zeroing).
  • LED blinks when I'm reading logic level voltage or higher.
  • Simultaneous current and voltage measurement abilities (requires a Hall sensor-based ammeter module).
  • Data logging for current and voltage, with customizable triggers to autolog both.

Raspberry Pi user interface

The repository now includes a Raspberry Pi-friendly interface that mirrors the firmware display and logging features. The UI is written in Python using Tkinter so it ships with Raspberry Pi OS and can run directly on the framebuffer or under X11. To start the dashboard with the built-in demo generator run:

text
python3 -m raspi_port.app

In deployment the measurement host should feed real readings to the MicroDmmApp class instead of the demo thread. The window presents the same information rendered by updateDisplay()—live voltage or resistance with min/max tracking, current when enabled, the active mode, timestamps, delta/null information, and log counters. Interaction hotkeys replace the touch panel:

FunctionTouch colorHotkeyDescription
Mode cycleRedMAdvances through the measurement modes.
Manual logGreenLAppends the most recent sample buffer to ~/micro_dmm_logs/data.csv.
Auto log export–AWrites the auto-log buffer to ~/micro_dmm_logs/data_autologged.csv.
Min/Max resetBlueZClears the stored extrema, just like tapping “Min/Max”.
Type/ΔYellowTIn Type mode it writes the displayed value to typed_entries.txt; otherwise it arms the delta/null workflow.

On a Raspberry Pi you can optionally map these controls to hardware buttons by defining a MICRO_DMM_GPIO environment variable before launching the program. The value is a comma-separated list such as mode=5,manual_log=6,auto_log=13,minmax=19,type=26. Each entry binds a GPIO pin (using gpiozero.Button) to the corresponding action.

All log exports stay on the Pi’s filesystem under ~/micro_dmm_logs/. The CSV layouts match the firmware’s logCurrentData() and autologArraysToCSV() routines so downstream tooling continues to work. The typed_entries.txt file replaces the USB keyboard emulator and captures the same formatted text that would have been “typed” into a host PC, while also echoing it to stdout for quick clipboard-style use.

I have a long and detailed write-up of the circuitry design on my personal website: https://www.oihdesigns.com/arduino-multimeter-project

There are a couple videos here: https://youtu.be/rzj-ar2Qv_A and here: https://youtu.be/hZ4eH-7RNsU

Here are more photos:

20250623_205043_760_1DXII copy 20250623_202545_180_1DXII copy 20250623_203203_470_1DXII copy

Design Prioities and Compromises:

This meter is designed to complement and support the more expensive equimpent generally found in a lab, rather than replace it. With that in mide, I've made the following design decisions on my priorites:

Minimal Protections

  • The voltmeter circuitry is not designed to measure amplitudes higher than is dangerous to humans. By not designing a tool that is supposed to keep people safe I can dramatically simplify and shrink the design. (The said, I've nailed the voltmeter circuit with a 1000V megaohmmeter. No problem.)
  • Likewise, the resistance circuit can be damaged if you accidentally measure too much /unregulated voltage. This is a tradeoff for a very fast and accurate autoranging ohmmeter circuit that can accurately read from less than 0.01 to more than 5,000,000 Ohms.

Streamlined Functions

  • There is no built in ammeter, inductance, or capacitance function. Ammeter function is easily added as needed with either an off-the-shelf module, or a low value resistor across the voltmeter. There isn't an easy way to add indutance or capacitance. I don't use any of these often enough for them to be worth taking up the PCB space.

Current Support:

As of writing I have functional versions (I confirmed the core functions work) that support the:

  • Arduino Uno R4
  • Arduino Giga (with or without the display shield)
  • Arduino ESP32 Nano (via jumpers)
  • Seeed Studio XIAO RA4M1 (same processer as the Uno R4)
  • I have partial function on a direct computer (Windows 11) interface with a FT232H breakout board (AdaFruit makes a nice one). I can see the data lines and it looks like most of the logic works, more or less. It's a proof of concept port and a test for "can I tell the AI to take an Arduino sketch and port it to Python" (the answer is far more yes than it use to be).
    • That said, it's very slow (reading in at 2-3sps). I'm not sure how to optimize this, and speeding it up is not an immediate priority.

2025-06-30 15 28 38-1 2025-06-25 20 25 30

Future Plans:

Major Function Things to Address:

  • Writing to MicroSD cards over the AUX SPI Bux on the RA4M1 XIAO boards. I set this up and tested it, but it didn't work and needs to be troubleshot.
  • Getting the code to run on the XIAO RP2350 board. It compiles but does not run.

Potential Refinements To-Do List:

  • Revise the PCB design to shrink the physical size (the current design was made with hand-soldering in mind). This would involve:
    • Smaller footprint components for things like the pullup resistors.
    • Dedicated multiple transistor packages for the switching functions rather than the discreet components.
    • There are probably other ways to shrink the design.
    • There is some potential performance improvement room to the analog circuit if I take advantage of the ADS1115's max input voltage of ~6.144vdc instead of 5vdc.
  • There is always room for cleanup in the code to make it more elegant.

Ideas for Expanding on the Current Function / :

  • Make a version that uses an ADS1256 instead of the ADS1115 to support measurements speeds up to 30,000 samples/second and resolutions of up to 24bits. (I have had proof-of-concept success with this using a Raspberry PI ADS1256 hat.)
  • Make a version that runs off a Raspberry Pi.
  • Implement WiFi/Bluetooth features on the boards that support it.
  • Implement DAC output as a simple function generator for the boards that support it.
  • Add a jumper on the PCB and write the code to allow four-wire resistance readings.

If you're interested in helping develop this please feel free to reach out.

FAQ:

  • Q: What is the logic voltage?

    • A: The current PCB works for either 3.3 or 5vdc.
  • Q: Is there voltage isolation on the USB?

    • A: There is enough isolation (500K Ohms) that you will not hurt anything by measuring voltage (in either polarity) on something connected to the wall while the meter is also connected to the wall, but not enough to prevent ground loops from interfering with measurements. See the longer, full write up on my website, and then buy the Adafruit USB voltage isolation board.
  • Q: The Adafruit isolation board says "100mA." What does the meter draw?

    • A: With the XIAO RA4M1, 50-60mA typical when measuring voltage. Closer to 100mA when measuring resistance. The resistance circuit goes into low-power mode several seconds after being open (except in a no-sleep mode).
  • Q: Does it work on an Arduino Uno R3?

    • A: As a basic meter, yes, but there's no keyboard emulation.
  • Q: Can I buy one?

    • A: Eventually, yes, probably? I do not have a current timeline for bringing these to market. If you want one please reach out to me. If you want to hand-solder it yourself I can sell you a single PCB and maybe some of the components with higher individual costs.

Parts

27
QtyValueFootprintReferences
4MountingHoleMountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2, H3, H4
210KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR3, R8
24.7uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC9, C10
2499.0KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR17, R18
2D_SchottkyDiode_SMD:D_SOD-123D4, D5
10.1uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC17
11.0MResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR24
1100KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR12
115.0KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR14
11KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
122KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR7
14.7KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR27
1AO3400A MOSFETPackage_TO_SOT_SMD:SOT-23Q8
1Barrel_JackTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_HorizontalJ15
1LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD1
1LM4040DBZ-2.5Package_TO_SOT_SMD:SOT-23U10
1MAX1683Package_TO_SOT_SMD:SOT-23-5_HandSolderingU7
1MMBT3904Package_TO_SOT_SMD:SOT-23Q3
1SW_PushButton_Switch_SMD:SW_SPST_CK_RS282G05A3SW3
1VoltmeterConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ1

More from oihdesigns/Micro-DMM

12
  • 4 layers68.5 × 53.3 mmDMM KiCAD V4 next, the printed circuit board in 3D

    DMM KiCAD V4 next

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    80 parts2
  • 4 layers88.9 × 50.8 mmNametagVoltmeter, the printed circuit board in 3D

    NametagVoltmeter

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    66 parts2
  • 4 layers85.5 × 47.4 mmDMM Feather Redux, the printed circuit board in 3D

    DMM Feather Redux

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    61 parts2
  • 4 layers66 × 37.1 mmDualAMCBoard, the printed circuit board in 3D

    DualAMCBoard

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    59 parts2
  • 4 layers68.5 × 53.3 mmDMM Feather Specific, the printed circuit board in 3D

    DMM Feather Specific

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    57 parts2
  • 2 layers60 × 50 mmAD8237DevBoard, the printed circuit board in 3D

    AD8237DevBoard

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    56 parts2
  • 4 layers46 × 24.4 mmAnalogFrontEnd, the printed circuit board in 3D

    AnalogFrontEnd

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    52 parts2
  • 4 layers30.4 × 61.2 mmOpenLead Headless V2, the printed circuit board in 3D

    OpenLead Headless V2

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    44 parts2
  • 4 layers48.7 × 59.1 mmVoltmeterFrontEnd V2, the printed circuit board in 3D

    VoltmeterFrontEnd V2

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    42 parts2

Similar boards

  • 4 layers95 × 55.5 mmEinkPDA keyboard, the printed circuit board in 3D

    EinkPDA keyboard

    TalismanDesign/PocketMage_PDA

    An E-Ink PDA device using the ESP32 S3.

    137 parts2kApache-2.0
  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers90 × 25.5 mmBadgeMagic, the printed circuit board in 3D

    BadgeMagic

    fossasia/badgemagic-hardware

    Badge Magic Hardware Board

    525 parts1.5kApache-2.0
  • 4 layers85 × 56 mmPslab mini, the printed circuit board in 3D

    Pslab mini

    fossasia/pslab-mini-hardware

    PSLab Mini Hardware https://pslab.io

    182 parts1.2kApache-2.0
  • 4 layers74.5 × 70.3 mmNest mini v2-drop in pcb, the printed circuit board in 3D

    Nest mini v2-drop in pcb

    iMike78/nest-mini-drop-in-pcb

    Drop-in PCB replacement for the Google Nest Mini v2 with ESP32-S3, ESP32-P4 and optional ESP32-C6. Inspired by Onju Voice and Home Assistant Voice PE.

    229 parts628CERN-OHL-S-2.0
  • 2 layers148 × 84.5 mmPanel daisy, the printed circuit board in 3D

    Panel daisy

    ohmtech-rdi/eurorack-blocks

    Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

    259 parts410
  • 4 layers46.8 × 34.8 mmSmartWatch V4, the printed circuit board in 3D

    SmartWatch V4

    Bellafaire/ESP32-Smart-Watch

    An open source smartwatch based on the ESP32 compatible with the Arduino IDE.

    74 parts258MIT
  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0

Questions

How big is the VoltmeterFrontEnd PCB?

It measures 47.5 × 26 mm and has 4 copper layers, 1.6 mm thick.

What parts does the VoltmeterFrontEnd use?

27 parts, built around the MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the VoltmeterFrontEnd KiCad files?

From the oihdesigns/Micro-DMM repository on GitHub, at the commit this page was made from: the board is PCBDesigns/VoltmeterFrontEnd/VoltmeterFrontEnd.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the VoltmeterFrontEnd design in my own project?

Its repository states no licence, so its author keeps all rights: ask oihdesigns before reusing the design.