Skip to the content
6 layers74 × 140 mmPocket synth, the printed circuit board in 3D

STM32H743ZI-based pocket-sized sequencer with synth engines and sampler, velocity pads, MPE aftertouch, BLE MIDI, Bluetooth audio, and more.

Size
74 × 140 mm
Copper layers
6
Thickness
1.6 mm
Parts
385
Nets
357
Pads
1,549
Tracks, vias
2,511, 623
Pours
17
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
6 Sep 2025
Updated
27 Jan 2026

Overview

Pocket synth is an open-source printed circuit board by northernpaws, from the northernpaws/pocketsequencer repository on GitHub. It is a 6-layer board of 74 × 140 mm with 385 parts on 357 nets, routed with 2,511 tracks and 623 vias.

It is built around the ADS7128IRTER, DA7280-00FVC and BQ24193RGE, with the BQ27531YZFR-G1, 1N4148WS and 7E032768H01 among its other parts. Its parts include 118 capacitors, 60 resistors, 34 diodes, 8 ICs and 5 inductors. It belongs with the audio and music and radio and wireless boards of this library.

Main components

6

README

hardware/boards/v0.1/README.md

v0.1

Components

Observations

Routing

  • In next revision, use larger STM32 package. Ran out of pins on the left side due to the FMC and SDRAM, and had to route several GPIO across the entire board, including some interrupt traces in the power layer. Ran out of ADC pins for the velocity pads and had to add an $8 IO expander.

Errata

  • QUADSPI CS should be NSS capable pin for automatic hardware peripheral control. Use PG6 and swap USB_INT to PD6.
  • Micro SD Card detect pins weren't connected, card detection needs to happen in software.
  • SPI1 hardward CS pins should be PA4, PA15, or PG10. Currently using PA4 (SD CARD) and PC13 (internal flash).
  • Unused key matrix pins should be connected to VCC via a pull-up.
  • Keypad diodes should be pointing to the columns, not the rows.
    • "Once the TCA8418 has had the keypad array configured, it will enter idle mode when no keys are being pressed. All columns configured as part of the keypad array will be driven low and all rows configured as part of the keypad array will be set to inputs, with pull-up resistors enabled. During idle mode, the internal oscillator is turned off so that power consumption is low as the device awaits a key press."
  • Missing pull-up on keypad interrupt. Compensated for in software.
  • Fuel gauge interrupt missing pull-up resistor.
  • Mounting holes are not grounded, oops..
  • PG and cahrger lights are on regardless of power state
  • Should have a 3v3 power light
  • Somehow connect vref from the BMP port to the power button on confirmation
  • Should add flow control pins to RF UART "H:4 HCI transport protocol (requires HW flow control from the UART)".
  • Touch screen connector is inverted...
  • LED footprint needs longer pads with some overhang
  • Dispaly connector needs slightly longer pads
  • Display mode pins are backwards...
  • LEDs need a power enable switch tied to the main regulator, they never shut off.
  • Either attach power enable pin to the BMP's Vref so the BMP can assert it high, or have a flashing/development jumper on the back.
  • TCA8418 doesn't provide a way to query the matrix state after an active reset. The TAC8418 only emits keypress events when they happen, so we can't check on power on if a key is held from before a reset.
  • The filtering capacitors on the audio line in and out are too small, they should be at least 47uF. In their current 1uF value, they cut out large parts of the low-end.
  • The filter capacitors on the audio line in and out where acidentally changed from film to ceramics during BOM selections, causing extra signal noise.

Parts

385
QtyValueFootprintReferences
401uFCapacitor_SMD:C_0402_1005MetricC3, C16, C18, C23, C32, C33, C34, C35, C38, C42, C105, C107, C114, C118, C119, C120 +24
35100nFCapacitor_SMD:C_0402_1005MetricC10, C15, C17, C20, C21, C24, C39, C40, C41, C46, C48, C49, C56, C57, C100, C102 +19
331N4148WSDiode_SMD:D_SOD-323D1, D2, D10, D11, D12, D13, D14, D15, D16, D18, D22, D23, D24, D25, D26, D27 +17
2410kResistor_SMD:R_0402_1005MetricR2, R10, R11, R13, R14, R15, R16, R17, R18, R20, R22, R27, R29, R35, R36, R37 +8
1210uFCapacitor_SMD:C_0402_1005MetricC11, C19, C22, C25, C58, C80, C101, C103, C109, C112, C113, C115
84.7uFCapacitor_SMD:C_0402_1005MetricC9, C27, C29, C30, C31, C52, C53, C108
8FiducialPCM_kikit:FiducialFID1, FID2, FID3, FID4, FID5, FID6, FID7, FID8
54.7kResistor_SMD:R_0402_1005MetricR38, R41, R43, R44, R50
410kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR28, R30, R31, R32
41k@100MhzInductor_SMD:L_0603_1608MetricFB1, FB2, FB3, FB4
42.2kResistor_SMD:R_0402_1005MetricR5, R19, R25, R55
4M3MountingHole:MountingHole_2.2mm_M2_PadH1, H2, H3, H4
3100kResistor_SMD:R_0402_1005MetricR39, R48, R49
32.2uFCapacitor_SMD:C_0402_1005MetricC1, C2, C106
3LOGOLOGOG***, G***, G***
20RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR24, R46
20RResistor_SMD:R_0402_1005MetricR33, R64
210nfCapacitor_SMD:C_0402_1005MetricC88, C104
210pFCapacitor_SMD:C_0402_1005MetricC6, C14
216pFCapacitor_SMD:C_0603_1608MetricC4, C5
2220pFCapacitor_SMD:C_0402_1005MetricC37, C43
2220uFCapacitor_SMD:CP_Elec_5x5.4C36, C54
222nFCapacitor_SMD:C_0402_1005MetricC28, C45
222uFCapacitor_SMD:C_0402_1005MetricC97, C99
2270nH Q>15@100MHzInductor_SMD:L_0603_1608MetricL2, L3
1+BATTTestPoint:TestPoint_Pad_D1.0mmTP51
10.033uFCapacitor_SMD:C_0603_1608MetricC26
10.750RResistor_SMD:R_0402_1005MetricR52
10RResistor_SMD:R_0603_1608MetricR72
11.8kResistor_SMD:R_0603_1608MetricR40
110uH 20%Inductor_SMD:L_0805_2012MetricL5
110Ω 5% 0.25WResistor_SMD:R_0402_1005MetricR8
1120RInductor_SMD:L_0603_1608MetricFB9
1120pFCapacitor_SMD:C_0805_2012MetricC13
118k2Resistor_SMD:R_0402_1005MetricR45
11M80Resistor_SMD:R_0402_1005MetricR42
11kResistor_SMD:R_0402_1005MetricR47
11nFCapacitor_SMD:C_0402_1005MetricC44
11uF 50VCapacitor_SMD:C_0603_1608MetricC110
11uHInductor_SMD:L_1008_2520MetricL1
12.2uHInductor_SMD:L_0805_2012MetricL6
120kResistor_SMD:R_0402_1005MetricR21
1220RResistor_SMD:R_0402_1005MetricR12
122uFCapacitor_SMD:C_0805_2012MetricC12
1255RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR6
128V 3AFuse:Fuse_1206_3216MetricF1
133R 5% 0.5WResistor_SMD:R_1206_3216MetricR3
13v3TestPoint:TestPoint_Pad_D1.0mmTP14
147nFCapacitor_SMD:C_0603_1608MetricC111
1499kResistor_SMD:R_0402_1005MetricR63
15k6Resistor_SMD:R_0402_1005MetricR1
15mΩResistor_SMD:R_1210_3225MetricR26
17E032768H01pocket_synth:SMD1612-4PY1
180k6Resistor_SMD:R_0402_1005MetricR34
190kResistor_SMD:R_1206_3216MetricR23
1ADS7128IRTERpocket_synth:ADS7128IRTERU38
1AUX_LTestPoint:TestPoint_Pad_D1.0mmTP37
1AUX_RTestPoint:TestPoint_Pad_D1.0mmTP39
1BACKLIGHTTestPoint:TestPoint_Pad_D1.0mmTP47
1BMDUpocket_synth:CON10_2X5_DUK_FTSH_SAI-MU1
1BOOT0Button_Switch_SMD:SW_SPST_B3U-1000PSW25
1BQ24193Package_DFN_QFN:VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalViasU45
1BQ27531YZFR-G1pocket_synth:BGA15C50P3X5_196X261X63U39
1BSCLTestPoint:TestPoint_Pad_D1.0mmTP30
1BSDATestPoint:TestPoint_Pad_D1.0mmTP48
1Batterypocket_synth:CONN_2082940000-SD_02_MOLBT1
1CC1TestPoint:TestPoint_Pad_D1.0mmTP25
1CC2TestPoint:TestPoint_Pad_D1.0mmTP26
1CHGLED_SMD:LED_0805_2012MetricD19
1CLKTestPoint:TestPoint_Pad_D1.0mmTP41
1D+TestPoint:TestPoint_Pad_D1.0mmTP21
1D-TestPoint:TestPoint_Pad_D1.0mmTP22
1DA7280-00FVCpocket_synth:DA7280-00FVCIC2
1DAEX-9-4SMConnector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_VerticalJ12
1ER-TFT028A-4pocket_synth:ER-TFT028A2-4U26
1ER-TPC028-4.1pocket_synth:ER-CON06HB-1U37
1FUSB302BxxMPXPackage_DFN_QFN:WQFN-14-1EP_2.5x2.5mm_P0.5mm_EP1.45x1.45mmU23
1GNDTestPoint:TestPoint_Pad_D1.0mmTP24
1HPConnector_PinHeader_2.00mm:PinHeader_1x03_P2.00mm_VerticalJ7
1IN_LTestPoint:TestPoint_Pad_D1.0mmTP35

The 265 most common of 385 parts.

More from northernpaws/pocketsequencer

1
  • 6 layers155 × 162 mmPocket synth v0.2, the printed circuit board in 3D

    Pocket synth v0.2

    northernpaws/pocketsequencer

    STM32H743ZI-based pocket-sized sequencer with synth engines and sampler, velocity pads, MPE aftertouch, BLE MIDI, Bluetooth audio, and more.

    64 parts

Similar boards

  • 6 layers70 × 80 mmCm5-carrier v2, the printed circuit board in 3D

    Cm5-carrier v2

    ben5049/cm-carrier-hardware

    Compact CM5 carrier board with an M.2 E-key connector and a 1000BASE-T1 Ethernet PHY, as well as other optional IO.

    334 parts1AGPL-3.0
  • 2 layers24.3 × 42.1 mmWireless wizard wand, the printed circuit board in 3D

    Wireless wizard wand

    finnfi/wireless-wizard-wand

    Nordic Semiconductor Wireless Wizard Wand (WWW) using nRF52840 with Edge Impulse ML motion recognition.

    15 parts
  • 2 layers83.8 × 31.8 mmBalthazarPSU, the printed circuit board in 3D

    BalthazarPSU

    Turbosavski/balthazarPSU

    Balthazar open-hardware laptop - PSU charger + audio amplifier module

    88 parts3
  • 2 layers126.7 × 25.3 mmBalthazarPSU2, the printed circuit board in 3D

    BalthazarPSU2

    balthazar-space/Balthazar-PSU-IO-v.2

    Balthazar open-hardware laptop - version 2 of keyboard and touchpad module controller

    148 parts2
  • 2 layers134 × 88 mmTulipcc, the printed circuit board in 3D

    Tulipcc

    shorepine/tulipcc

    The Tulip Creative Computer and AMYboard - portable Python synthesizers

    103 parts978
  • 8 layers100.2 × 55 mmJetson nano baseboard, the printed circuit board in 3D

    Jetson nano baseboard

    antmicro/jetson-nano-baseboard

    Antmicro's open hardware baseboard for the NVIDIA Jetson Nano, TX2 NX and Xavier NX

    391 parts548Apache-2.0
  • 4 layers94.4 × 72.8 mmRP2040 base, the printed circuit board in 3D

    RP2040 base

    Twisted-Fields/rp2040-motor-controller

    A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.

    325 parts419
  • 2 layers135.9 × 89.5 mmLeft, the printed circuit board in 3D

    Left

    TeXitoi/keyseebee

    KeySeeBee is a split ergo keyboard. It is only 2 PCB (so the name) with (almost) only SMD components on it. It's only a keyboard, no LED, no display, nothing more than keys and USB.

    61 parts348MIT

Questions

How big is the Pocket synth PCB?

It measures 74 × 140 mm and has 6 copper layers, 1.6 mm thick.

What parts does the Pocket synth use?

385 parts, built around the ADS7128IRTER, DA7280-00FVC, BQ24193RGE and BQ27531YZFR-G1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pocket synth KiCad files?

From the northernpaws/pocketsequencer repository on GitHub, at the commit this page was made from: the board is hardware/boards/v0.1/pocket_synth.kicad_pcb and its schematic hardware/boards/v0.1/MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pocket synth design in my own project?

Its repository states no licence, so its author keeps all rights: ask northernpaws before reusing the design.