4 layers72.6 × 170 mm
OpenJBOD RP2040
OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
129 parts87CERN-OHL-P-2.0
2 layers44.9 × 54.7 mm
Devboard
NoIwantyourcode/DevboardThis is a custom devboard I have made which uses an RP2040 along with 40 GPIO pins, This also has an inbuild MPU-6500 IMU for all of your tilt and acceleration measuring needs!
- Size
- 44.9 × 54.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 75
- Pads
- 231
- Tracks, vias
- 607, 77
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 19 May 2026
- Updated
- 13 Oct 2026
Overview
Devboard is an open-source printed circuit board by NoIwantyourcode, from the NoIwantyourcode/Devboard repository on GitHub. It is a 2-layer board of 44.9 × 54.7 mm with 42 parts on 75 nets, routed with 607 tracks and 77 vias.
It is built around the RP2040, W25Q128JVSIQ and MPU-6500, with the SS14 among its other parts. Its parts include 21 capacitors, 8 resistors, 5 connectors, 4 ICs and 1 diode. It belongs with the microcontroller boards boards and the RP2040 boards of this library.
Main components
4
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
MPU-6500
QFN-24-40℃~+85℃ 16bit 6uA Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(3x3) Accelerometers ROHSTDK InvenSenseAccelerometers
SS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdWhat is this Devboard
This is a custom devboard I have made which uses an RP2040 along with 40 GPIO pins, This also has an inbuild MPU-6500 IMU for all of your tilt and acceleration measuring needs!
Why I built this
I built this because I was extremely bored on one fine Sunday morning and decided to embark on this project to teach myself about robots and how to design them
Pictures of the Devboard
Schematics - DevBoard
PCB board - DevBoard
PCB Board - 3D render
PCB board assembled and working!
Demo!
Goto
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12 |
| 2 | 0.1uF | PCM_SparkFun-Capacitor:C_0603_1608Metric | C20, C21 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C14 |
| 2 | 15pF | PCM_SparkFun-Capacitor:C_0402_1005Metric | C15, C16 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R4 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2 |
| 2 | Conn_01x20 | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J3, J4 |
| 1 | 0.1uF | PCM_SparkFun-Capacitor:C_0402_1005Metric | C17 |
| 1 | 100K | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | R8 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7 |
| 1 | 10nF | PCM_SparkFun-Capacitor:C_0603_1608Metric | C19 |
| 1 | 12Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1 |
| 1 | 47uF | PCM_SparkFun-Capacitor:C_0603_1608Metric | C18 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | JST_2mm_LiPo | Connector_JST:JST_XA_S02B-XASK-1N-BN_1x02_P2.50mm_Horizontal | J5 |
| 1 | LOGO | F16art:f16-40mm | G*** |
| 1 | MPU-6500 | KiCadMPU:QFN40P300X300X95-25N-D | IC1 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | SS14 | PCM_Diode_SMD_AKL:D_SMA | D1 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |
Questions
How big is the Devboard PCB?
It measures 44.9 × 54.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Devboard use?
42 parts, built around the RP2040, W25Q128JVSIQ, MPU-6500 and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Devboard KiCad files?
From the NoIwantyourcode/Devboard repository on GitHub, at the commit this page was made from: the board is PCB files/Devboard.kicad_pcb and its schematic PCB files/Devboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Devboard design in my own project?
Its repository states no licence, so its author keeps all rights: ask NoIwantyourcode before reusing the design.
Similar boards
- 4 layers92 × 56 mm
REIN R1
rein-baremetal/REIN_R1_KiCad
Dual-MCU baremetal embedded development board featuring high-speed QSPI storage, hardware USB hub, and flexible power management. Open for PCB trace routing collaboration
177 parts2 - 4 layers279.5 × 97 mm
Alpha centauri pcb
jacob-w-gable/alpha_centauri
A split, ergonomic, mechanical keyboard with 40 keys, designed for typing speed and comfort.
224 parts1MIT - 2 layers304.8 × 95.3 mm
- 4 layers65 × 30 mm
- 2 layers285.7 × 123.8 mm
- 2 layers45 × 45 mm
Mini games
louis-bourgault/macondo-games
a cool little games console that i'm making for hack club macondo. also can be played on the web.
53 parts2AGPL-3.0 - 4 layers45.7 × 76.2 mm
Node v5 0 0
VTC-WISDOM/node_hardware
Schematic/PCB designs for WiSDOM nodes, also includes a few other related hardware projects
103 parts2CERN-OHL-W-2.0