4 layers170.2 × 92 mm
CM4 JBOD Control Board
ApplePie420/OpenJBOD-CM4
This project is heavily inspired by the work of TheGuyDanish, specifically his OpenJBOD thingamajig.
78 parts3
4 layers72.6 × 170 mm
OpenJBOD RP2040
OpenJBOD/rp204087This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
- Size
- 72.6 × 170 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 129
- Nets
- 144
- Pads
- 543
- Tracks, vias
- 882, 134
- Pours
- 410
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Aug 2024
- Updated
- 29 Aug 2025
Overview
OpenJBOD RP2040 is an open-source printed circuit board by OpenJBOD, from the OpenJBOD/rp2040 repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 4-layer board of 72.6 × 170 mm with 129 parts on 144 nets, routed with 882 tracks and 134 vias.
It is built around the RP2040, 74LVC1G07 and DS18B20U, with the W25Q128JVSIQ, 74LVC1G02Z and AMS1117-3.3 among its other parts. Its parts include 46 capacitors, 41 resistors, 10 ICs, 8 connectors and 4 diodes. It belongs with the RP2040 boards of this library.
Main components
12
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
74LVC1G07
SOT-353-40℃~+105℃ 1 1 1.65V~5.5V 1.6ns@5.5V,50pF 24mA 4uA 74LVC Open-drain Power-off isolation、Level shifting Unidirectional SOT-353 Buffers, Drivers, Receivers, Transceivers ROHSWuxi I-core ElecBuffers, Drivers, Receivers, Transceivers
DS18B20U
MSOP-8-55℃~+125℃ 12bit 2.5V~5.5V 400ms 750nA Single-bus ±0.4℃ MSOP-8 Temperature Sensors ROHSUMWTemperature Sensors
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
74LVC1G02Z
SOT-553-5-40℃~+125℃ 1 1.65V~5.5V 1.7V~2V 1.7ns@5V,50pF 2 200uA 3.4V~3.8V 32mA 32mA 550mV~800mV 700mV~800mV 74LVC Series NOR Gate SOT-553-5 Logic Gates ROHSDiodes IncorporatedLogic Gates
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
W5500
LQFP-48_7x7-40℃~+85℃ 10BASE-T、100BASE-TX 3.3V 32KB SPI SPI Wake-up function、Programmable LED indication、Low-power mode Yes LQFP-48(7x7) Ethernet Controllers ROHSWIZNETEthernet Controllers
TC-6615-6-260G
弯插-4P,6x6mm-25℃~+85℃ 100,000 cycles 12V 2.6N 50mA 6mm 6mm 6mm Black No Right Angle Round Button SPST With Bracket 弯插-4P,6x6mm Tactile Switches ROHSHCTLTactile Switches
MMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
SS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
HR911105A
插件0℃~+70℃ 1 Filtered Gold Non-PoE Phosphor bronze RJ45 Jack Right Angle Shielded With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSHANRUNEthernet Connectors / Modular Connectors (RJ45 RJ11)
MHK2396YGBTD
DIP-4-2.54mm-25℃~+85℃ 15mcd、20mcd 2.2V 20mA 568nm、587nm 78mW 80° Discrete Diode Frosted Yellow Lens, Frosted Green Lens Yellow, Green DIP-4-2.54mm LED Indication - Discrete ROHSMEIHUALED Indication - Discrete
README
README.mdOpenJBOD RP2040 Baseboard
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
For the accompanying software, please refer to:
Requirements
- The design was created on KiCad 8.0.2, it uses the default symbol and footprint libraries from it. If you have installed KiCad without the default libraries, you may experience missing symbols.
- Non-standard symbols, footprints and models are bundled in the repository and should load with the project.
Compatibility
The board is compatible with any standards-compliant ATX power supply.
For SAS expanders, any SAS expander that can operate with only power (i.e. no PCI-e communication) should be functional on the board.
The board has successfully been tested with:
- Adaptec AEC-82885T
Parts
129| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 100nF | Capacitor_SMD:C_0402_1005Metric | C10, C11, C12, C13, C14, C18, C19, C20, C21, C22, C23, C25, C26, C27, C29, C38 +8 |
| 13 | 4.7k | Resistor_SMD:R_0402_1005Metric | R5, R7, R11, R12, R13, R18, R27, R28, R29, R30, R31, R38, R40 |
| 6 | 47uF | Capacitor_SMD:CP_Elec_6.3x5.4 | C33, C34, C35, C36, C37, C39 |
| 5 | 330R | Resistor_SMD:R_0402_1005Metric | R1, R2, R6, R24, R25 |
| 5 | Conn_01x04 | Connector:FanPinHeader_1x04_P2.54mm_Vertical | FAN1, FAN2, FAN3, FAN4, FAN5 |
| 4 | 10k | Capacitor_SMD:C_0402_1005Metric | R32, R33, R34, R35 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C6, C17, C24 |
| 4 | 3.3R | Resistor_SMD:R_0603_1608Metric | R10, R15, R16, R17 |
| 4 | 49.9R | Resistor_SMD:R_0402_1005Metric | R19, R20, R21, R22 |
| 3 | MountingHole_Pad | MountingHole:MountingHole_4.3mm_M4_Pad_Via | H1, H2, H3 |
| 3 | TC-6615-6-260G | OpenJBOD_Library:KEY-TH_TC-6615-6-160G | SW1, SW2, SW3 |
| 2 | 18pF | Capacitor_SMD:C_0402_1005Metric | C31, C32 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 22nF | Capacitor_SMD:C_0402_1005Metric | C30, C46 |
| 2 | 27.4R | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 34pF | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 5.1k | Capacitor_SMD:C_0402_1005Metric | R36, R37 |
| 2 | 6.8nF | Capacitor_SMD:C_0402_1005Metric | C40, C41 |
| 2 | 74LVC1G02 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U5, U7 |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SS14 | Diode_SMD:D_SMA | D2, D3 |
| 1 | 100R | Capacitor_SMD:C_0402_1005Metric | R41 |
| 1 | 100k | Capacitor_SMD:C_0402_1005Metric | R39 |
| 1 | 10R | Resistor_SMD:R_0402_1005Metric | R23 |
| 1 | 12.4k | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R26 |
| 1 | 1nF/2kV | Capacitor_SMD:C_1206_3216Metric | C42 |
| 1 | 22uF | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | 22uF Tant | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C2 |
| 1 | 24AA025E-OT | Package_TO_SOT_SMD:SOT-23-6 | U9 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C28 |
| 1 | 74LVC1G07 | Package_TO_SOT_SMD:SOT-23-5 | U10 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ATX-24 | OpenJBOD_Library:CONN-TH_M4202V-2X12P | J1 |
| 1 | Bus_PCI_Express_x1 | OpenJBOD_Library:91618-11010C | J2 |
| 1 | Conn_02x02_Counter_Clockwise | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J3 |
| 1 | DS18B20U | Package_SO:MSOP-8_3x3mm_P0.65mm | U8 |
| 1 | EMC2301 | Package_SO:MSOP-8_3x3mm_P0.65mm | U6 |
| 1 | FerriteBead_Small | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | FB1 |
| 1 | G*** | kibuzzard-68B1B461 | kibuzzard-68B1B461 |
| 1 | G*** | kibuzzard-68B1B45A | kibuzzard-68B1B45A |
| 1 | HR911105A | OpenJBOD_Library:RJ45-TH_HR911105A | J6 |
| 1 | MHK2396YGBTD | OpenJBOD_Library:LED-TH_MHK2396YGBTD | D1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | SDMK0340L | Diode_SMD:D_SOD-323 | D4 |
| 1 | TC2030-IDC-NL | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J8 |
| 1 | TEMP1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J4 |
| 1 | USB_C_Receptacle_USB2.0_16P | OpenJBOD_Library:USB-C-SMD_TYPE-C16PIN | J5 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
| 1 | W5500 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | X322512MSB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | X322525MOB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
The 127 most common of 129 parts.
Questions
How big is the OpenJBOD RP2040 PCB?
It measures 72.6 × 170 mm and has 4 copper layers, 1.61 mm thick.
What parts does the OpenJBOD RP2040 use?
129 parts, built around the RP2040, 74LVC1G07, DS18B20U and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the OpenJBOD RP2040 KiCad files?
From the OpenJBOD/rp2040 repository on GitHub, at the commit this page was made from: the board is OpenJBOD-RP2040.kicad_pcb and its schematic Environment.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the OpenJBOD RP2040 design in my own project?
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers90 × 66 mm
Iron node
enkhbold470/iron-node
ESP32-S3 industrial gateway: W5500 Ethernet, isolated RS-485 (ADM2587E), CAN, 9-36 V input. 4-layer KiCad 10 board.
83 partsCERN-OHL-S-2.0 - 2 layers51.4 × 61 mm
- 2 layers200 × 170 mm
Routing R1
ddasdkimo/rack-atx-controller
10-host isolated ATX rack controller hardware planning, interactive 3D model and wiring documentation
698 parts - 4 layers120 × 80 mm
- 4 layers80 × 100 mm
Baseboard
NVIDIA-AI-IOT/my-jetson-nano-baseboard
An open source Jetson Nano baseboard and tools to design your own.
240 parts91 - 4 layers110 × 80 mm
Esp32p4 extreme
Andreuxxx1977/esp32-p4
An open-hardware, actively cooled ESP32-P4 board for heavy multimedia work: a 2-lane MIPI camera, a 2-lane MIPI display, USB 2.0 High-Speed, 10/100 Ethernet, UHS-I microSD, 32 MB flash and 32 MB PSRAM.
234 parts1CERN-OHL-P-2.0 - 4 layers100 × 75 mm
Freedo radio
CappyT/freedo
Local coordinator for tado V3+ heating devices, with a Home Assistant integration and add-on
135 parts33Apache-2.0