
Sender
jsteiner4000/Kabelsuchger-t
Ein Gerät mit dem Kabel bzw einzelne Adern ausfindig machen kann.

Simple 4 channel Eurorack output mixer
Output mixer is an open-source printed circuit board by mohoyt, from the mohoyt/output_mixer repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 40 × 99 mm with 114 parts on 59 nets, routed with 755 tracks and 96 vias.
It is built around the TL072, B10K and BD139, with the BD140 among its other parts. Its parts include 56 resistors, 18 diodes, 16 capacitors, 6 connectors and 4 transistors. It belongs with the audio and music boards of this library.
Inspired by the mixer in the Erica Synths x mki.edu line (but with added channels and SMD components)
All addressed in current version (v1.1). The overheating was a result of poor quality BD139 and BD140 that I had sourced.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 1N4148 | Diode_SMD:D_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16 |
| 12 | 100k | Resistor_SMD:R_0805_2012Metric | R7, R8, R22, R31, R42, R45, R50, R51, R54, R55, R56, R57 |
| 8 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C4, C5, C6, C7, C8, C9, C12, C13 |
| 8 | 10k | Resistor_SMD:R_0805_2012Metric | R14, R15, R16, R17, R21, R27, R47, R48 |
| 8 | 1k | Resistor_SMD:R_0805_2012Metric | R3, R4, R28, R29, R32, R39, R40, R58 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C14, C15, C23 |
| 4 | 200k | Resistor_SMD:R_0805_2012Metric | R12, R13, R43, R46 |
| 4 | 2R0 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R24, R25, R36, R37 |
| 4 | 3.6k | Resistor_SMD:R_0603_1608Metric | R19, R20, R34, R35 |
| 4 | B100k | Potentiometer_THT:Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | R5, R6, R41, R44 |
| 4 | B10k | Potentiometer_THT:Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | R23, R49, R52, R53 |
| 4 | GND | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP5, TP6, TP7, TP8 |
| 3 | TL072 | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U1, U2, U3 |
| 2 | 10 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 2 | 1N5819 | Diode_SMD:D_SOD-323 | D17, D18 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C16, C17 |
| 2 | 30k | Resistor_SMD:R_0805_2012Metric | R18, R33 |
| 2 | 470 | Resistor_SMD:R_0805_2012Metric | R30, R59 |
| 2 | 47R 1W | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R26, R38 |
| 2 | 47uFx16V | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C2, C3 |
| 2 | BD139 | Package_TO_SOT_THT:TO-126-3_Vertical | Q2, Q4 |
| 2 | BD140 | Package_TO_SOT_THT:TO-126-3_Vertical | Q3, Q5 |
| 2 | IN1 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J1, J3 |
| 2 | IN2 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J2, J4 |
| 1 | A | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP1 |
| 1 | B | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP2 |
| 1 | C | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP3 |
| 1 | Conn_01x10 | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_Shroud | CONN1 |
| 1 | D | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP4 |
| 1 | E | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP9 |
| 1 | F | TestPoint:TestPoint_THTPad_D2.5mm_Drill1.2mm | TP10 |
| 1 | Headphones | AudioJacks:Jack_3.5mm_Stereo_Unbranded | J5 |
| 1 | Line out | AudioJacks:Jack_3.5mm_Stereo_Unbranded | J6 |

jsteiner4000/Kabelsuchger-t
Ein Gerät mit dem Kabel bzw einzelne Adern ausfindig machen kann.



xtarke/automated_buggy
This shield connects microcontroller (MSP-EXP430FR2355) pins to the car's power board. Go to Power Board for more hardware information.

prydin/opamp-frontend-class-ab
The result is a fast amplifier (>80V/us slew rate) with low distortion (0.00045% meadured @ 1kHz/1W/8ohm resistive load). It's undergone some preliminary measurements and looks quite promising.

dario0603/AB-class-amplifier
Design and simulation of a Class-AB audio power amplifier, focusing on output-stage linearity, crossover distortion reduction, and overcurrent protection.


Ogbonna-Joseph/1KVA-SINE-WAVE-POWER-INVERTER
This is a design of a sine wave power inverter, which can be used in your homes and offices.
It measures 40 × 99 mm and has 2 copper layers, 1.6 mm thick.
114 parts, built around the TL072, B10K, BD139 and BD140. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mohoyt/output_mixer repository on GitHub, at the commit this page was made from: the board is output_mixer.kicad_pcb and its schematic output_mixer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).