Skip to the content
2 layers90 × 32 mmSensor, the printed circuit board in 3D

3-phase brushless DC motor controller

Size
90 × 32 mm
Copper layers
2
Thickness
1.6 mm
Parts
42
Nets
24
Pads
104
Tracks, vias
267, 3
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
2 Feb 2022
Updated
16 Feb 2022

Overview

Sensor is an open-source printed circuit board by milan-simanek, from the milan-simanek/3-bldc repository on GitHub, published under the MIT licence. It is a 2-layer board of 90 × 32 mm with 42 parts on 24 nets, routed with 267 tracks and 3 vias.

It is built around the TLC272CD. Its parts include 25 resistors, 5 capacitors, 3 diodes and 2 connectors. It belongs with the robots and motor control and sensors and measurement boards of this library.

Main components

1

README

README.md

3-bldc

3-phase brushless DC motor controller

Features:

  • controls 3-phase BLDC motor
  • synchronization using opto-sensors

Arduino peripherals usage:

  • Timer0 - PWM
  • Timer1 - generic timer, phase detection
  • PB0:5 - phase output
    • PB0: phase 1 - high
    • PB1: phase 2 - high
    • PB2: phase 3 - high
    • PB3: phase 1 - low
    • PB4: phase 2 - low
    • PB5: phase 3 - low
  • PC0/PCINT8 - ~FAULT - overcurrent detection
  • PC3/ADC3 - output current measurement
  • PD0:1 - serial communication
  • PD2/INT0 = (zero angle = home position) detection (triggered by both edges)
  • PD3/INT1 = step sensor A
  • PD4 = step sensor B
  • PD5 = OC0B = PWM output

Issues:

  • opto-sensor feedback is currently amplified by operating amplifiers. Unfortunately, these devices should operate on higher voltage, so amplification is not so stable and produces flicking. Solution: signal from opto-sensors should be amplified and conditioned by CMOS invertor based schmitt trigger.

TODO:

  • rotation feedback could be derived from back-EMF.
  • maximum speed, acceleration measurements
  • use avrm modules for usart communication and text formating (comf)

Parts

42
QtyValueFootprintReferences
9100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R6, R7, R10, R14, R15, R18, R22, R23
310kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R12, R20
31kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R11, R19
3220Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR8, R16, R24
33k3Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5, R13, R21
347μCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2, C3
368kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR9, R17, R25
3LED_ALTLED_THT:LED_D3.0mmD1, D2, D3
3TLC272Package_DIP:DIP-8_W7.62mm_LongPadsIO1, IO2, IO3
1100μ/25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC4
11μCapacitor_THT:C_Rect_L16.5mm_W4.7mm_P15.00mm_MKTC5
1240Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1optoConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ1
1outputConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ2

The 38 most common of 42 parts.

More from milan-simanek/3-bldc

2
  • 2 layers85 × 85 mmPower, the printed circuit board in 3D

    Power

    milan-simanek/3-bldc

    3-phase brushless DC motor controller

    59 partsMIT
  • 2 layers90 × 32 mmSensor2, the printed circuit board in 3D

    Sensor2

    milan-simanek/3-bldc

    3-phase brushless DC motor controller

    6 partsMIT

Similar boards

  • 2 layers85 × 61 mmGBDSO, the printed circuit board in 3D

    GBDSO

    pyroesp/GBDSO

    Game Boy DSO Project revived in KiCad

    78 parts79
  • 2 layers200 × 87.8 mmSonus7 rev1, the printed circuit board in 3D

    Sonus7 rev1

    BasementCircuits/Sonus7

    Analog seven-band spectrum bargraph with op amps.

    263 parts6
  • 2 layers52.3 × 51.8 mmReBlast, the printed circuit board in 3D

    ReBlast

    SukkoPera/ReBlast

    8-Bit DAC/ADC Add-On for Commodore 16/Plus4 SIDcards

    27 parts6
  • 2 layers92.5 × 99.7 mmOpamp vu meter, the printed circuit board in 3D

    Opamp vu meter

    CASE-Association/christmas-cards

    All CASE christmas cards over the years

    48 parts3GPL-3.0
  • 2 layers50 × 40.9 mmGR ATTiny LFO, the printed circuit board in 3D

    GR ATTiny LFO

    GadgetReboot/ATTiny_LFO

    Dual low frequency oscillators using ATTiny and MCP4725 DACs

    36 parts3
  • 2 layers56.5 × 74 mmAscom flat panel, the printed circuit board in 3D

    Ascom flat panel

    letelescope/ascom-flat-panel

    Open source ASCOM and INDI driven automated flat panel for astrophotography

    17 parts2MIT
  • 2 layers43.5 × 46.9 mmSchaltplan Ultraschallsensor, the printed circuit board in 3D

    Schaltplan Ultraschallsensor

    Tinkerforge/distance-us-v2-bricklet-techniker

    This repository contains the firmware source code and the hardware design files. The documentation generator configs can be found at https://github.com/Tinkerforge/generators

    54 parts2
  • 2 layers85 × 56.5 mmMotherboard, the printed circuit board in 3D

    Motherboard

    BryggansBryggeri/electrical

    Electronics, hardware schematics

    34 parts1

Questions

How big is the Sensor PCB?

It measures 90 × 32 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Sensor use?

42 parts, built around the TLC272CD. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Sensor KiCad files?

From the milan-simanek/3-bldc repository on GitHub, at the commit this page was made from: the board is circuit/sensor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Sensor design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).