Skip to the content
2 layers18.4 × 12 mmMulti out, the printed circuit board in 3D

PCB boards designed to fit into a Nintendo multiout connector

Size
18.4 × 12 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
20
Pads
42
Tracks, vias
94, 7
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
1 May 2019
Updated
10 Nov 2020

Overview

Multi out is an open-source printed circuit board by mickednk, from the mickednk/multiout-to-bnc repository on GitHub. It is a 2-layer board of 18.4 × 12 mm with 17 parts on 20 nets, routed with 94 tracks and 7 vias.

It is built around the LM1881. Its parts include 5 capacitors, 2 resistors and 2 ICs.

Main components

1

README

readme.md

Multiout to BNC

The Console to BNC is a small project I put together to solve my snakepit of cables behind my consoles and Extron Crosspoint. this PCB board is the main part of the project and doesnt need to be used with BNC connectors, you can use it in combination with a SCART connector or regular RCA connectors. the purpose of the PCB is to move the components closer to the console.

SNES to BNC

This PCB is designed to be used with a NTSC SNES console, it will work with both a US SNES and a Japanese Super Famicom. It will also work with a NESRGB modified NES if it uses an multiout connector like the AV Famicom does. It might be compatible with other multiout consoles but it is designed with the NTSC SNES in mind.

Parts needed

Mouser part numberQuantityDescriptionDesignation
81-GRM31CR60J227ME1K3220uF capacitory 1206 packageC1, C2, C3

Gamecube to BNC

This PCB is designed to be used with a PAL Gamecube ONLY. It will not work with an NTSC Gamecube because they don't output RGB and I am pretty sure it would damage the monitor that you connect to.

Parts needed

Mouser part numberQuantityDescriptionDesignation
81-GRM31CR60J227ME1K3220uF capacitor 1206 packageC1, C2, C3
581-06036C104KAT2A20.1uF capacitor 603 packageC4, C5
71-CRCW0603680KFKEAC1680KOhm resistor 603 packageR1
71-CRCW060375R0FKEAC175Ohm resistor 603 packageR2
926-LM1881MX/NOPB1LM1881 Sync seperator circuitU2

PS2 to BNC

This PCB is designed to be used with Playstation 2 ONLY, it wont work with PS1 because it needs caps on the RGB lines to be compatible with PS1.

Parts needed

Mouser part numberQuantityDescriptionDesignation
581-06036C104KAT2A20.1uF capacitor 603 packageC1, C2
71-CRCW0603680KFKEAC1680KOhm resistor 603 packageR1
926-LM1881MX/NOPB1LM1881 Sync seperator circuitU1

Connectors

Nintendo consoles

The PCB is designed to use the knock off multiout connector that can be found at Console5.com (https://console5.com/store/nintendo-snes-super-famicom-n64-av-multi-out-plug-for-custom-rgb-cables-repair.html) I have seen it on Aliexpress as well so it shouldn't be to difficult to find.

Playstation consoles

The PCB is designed to use the knock off multiout connector that can be found at Console5.com (https://console5.com/store/sony-playstation-1-2-ps1-ps2-av-multi-out-plug-for-custom-rgb-cables-repair.html) I have seen it on Aliexpress as well so it shouldn't be to difficult to find.

Contribute to the project

I am not an electrical engineer so I have probably made tons of mistakes when routing and such, there is probably even more errors on the Gamecube one. With that said you are welcome to contribute by doing pull requests to this repository. I have taken this project as far as I need it but I can see how someone might want to build one for the PAL SNES or the N64.

Parts

17
QtyValueFootprintReferences
3220uFCapacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolderC1, C2, C3
20.1uFCapacitor_SMD:C_0603_1608MetricC4, C5
2GNDmulti-out:WIREPADGND, GND
2Rmulti-out:WIREPADAR, R
1680kResistor_SMD:R_0603_1608MetricR1
175kResistor_SMD:R_0603_1608MetricR2
1AV-CONNECTORmulti-out:AVCONU1
1Bmulti-out:WIREPADB
1CSmulti-out:WIREPADCS
1Gmulti-out:WIREPADG
1Lmulti-out:WIREPADAL
1LM1881Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU2

More from mickednk/multiout-to-bnc

2
  • 2 layers17.8 × 9.4 mmMultiout, the printed circuit board in 3D

    Multiout

    mickednk/multiout-to-bnc

    PCB boards designed to fit into a Nintendo multiout connector

    13 parts4
  • 2 layers18.4 × 12 mmMulti out, the printed circuit board in 3D

    Multi out

    mickednk/multiout-to-bnc

    PCB boards designed to fit into a Nintendo multiout connector

    12 parts4

Similar boards

  • 2 layers100 × 100 mmSync ope, the printed circuit board in 3D

    Sync ope

    cyberboy666/sync_ope

    effect send + sync restoring circuit - adapted from a gael jaton design

    78 parts52
  • 2 layers48.7 × 63.5 mmSCART to VGA, the printed circuit board in 3D

    SCART to VGA

    arithmaldor/SCART-to-VGA

    SCART to VGA adapter with optional sync stripper.

    15 parts46
  • 2 layers99 × 90 mmExtron input, the printed circuit board in 3D

    Extron input

    rattboi/extron-scart-adapter

    Cheap adapter for (some) extron matrix switchers to allow SCART input with no cables

    22 parts37
  • 2 layers50 × 70 mmRgbntsc, the printed circuit board in 3D

    Rgbntsc

    jamvanderloeff/RGB-to-NTSC

    Converts RGB 15kHz video in the form of VGA or SCART into NTSC and/or PAL composite and s-video using

    55 parts17MIT
  • 2 layers50 × 70 mmRGB to component, the printed circuit board in 3D

    RGB to component

    jamvanderloeff/RGB-to-component

    58 parts13MIT
  • 2 layers44.5 × 58.4 mmOverlay64, the printed circuit board in 3D

    Overlay64

    hbekel/overlay64

    video overlay module

    26 parts11GPL-3.0
  • 2 layers135.1 × 85.8 mmWinchester, the printed circuit board in 3D

    Winchester

    yoonjustin/WinchesterPCB

    Open source JAMMA supergun project. KiCAD PCB design files

    89 parts10MIT

Questions

How big is the Multi out PCB?

It measures 18.4 × 12 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Multi out use?

17 parts, built around the LM1881. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Multi out KiCad files?

From the mickednk/multiout-to-bnc repository on GitHub, at the commit this page was made from: the board is multiout-to-bnc/pal-gamecube/multi-out.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Multi out design in my own project?

Its repository states no licence, so its author keeps all rights: ask mickednk before reusing the design.