

Display board
- Size
- 100 × 103.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 66
- Nets
- 62
- Pads
- 219
- Tracks, vias
- 564, 70
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 Feb 2025
- Updated
- 3 Apr 2026
Overview
Display board is an open-source printed circuit board by mckay27, from the mckay27/hstat repository on GitHub. It is a 2-layer board of 100 × 103.5 mm with 66 parts on 62 nets, routed with 564 tracks and 70 vias.
It is built around the DS18B20Z, LTR-303ALS-01 and SHT41-AD1B-R2, with the TPS61165DBV, H8VHD3B and TS-1187A-B-A-B among its other parts. Its parts include 16 capacitors, 14 diodes, 11 resistors, 5 ICs and 4 switches. It belongs with the lEDs and displays boards of this library.
Main components
12DS18B20Z
SOIC-8-55℃~+125℃ 12bit 2.5V~5.5V 750ms Single-bus ±0.4℃ SOIC-8 Temperature Sensors ROHSUMWTemperature SensorsLTR-303ALS-01
DFN-6(2x2)-30℃~+70℃ 0.7mm 16bit 2.4V~3.6V 2mm 2mm 64klx I2C Light Intensity Low power/sleep mode、Spectral correction/filtering、Adjustable gain control、Interrupt/event trigger、Built-in temperature compensation DFN-6(2x2) Ambient Light Sensors ROHSLite-OnAmbient Light SensorsSHT41-AD1B-R2
DFN-4(1.5x1.5)-40℃~+125℃ 0%RH~100%RH 1.08V~3.6V 16bit 400nA Factory calibration、Built-in heater I2C ±0.2℃ ±1.8%RH DFN-4(1.5x1.5) Temperature and Humidity Sensor ROHSSensirionHumidity, Moisture SensorsTPS61165DBV
SOT-23-6-40℃~+85℃ 1 1.2A 1.2MHz 2% 3V~18V 3V~38V Boost Built-in DC-DC Over Voltage Protection、Over-Temperature Protection (OTP) PWM SOT-23-6 LED Drivers ROHSTexas InstrumentsLED DriversH8VHD3B
SOD-323-55℃~+125℃ 100nA 11.5V 120pF 20A@8/20us 25V 500W@8/20us 8V Bidirectional ESD IEC 61000-4-2、IEC 61000-4-5 Single-channel SOD-323 ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile SwitchesMBR0530-TP
SOD-123Schottky DiodesMicro Commercial ComponentsKT-0805G
0805-40℃~+85℃ 100mW 120° 2.6V~3.1V 430mcd 513nm~528nm 525nm 5mA Discrete Diode Emerald Green Water Clear 0805 LED Indication - Discrete ROHSHubei KENTO ElecLED Indication - DiscreteNRS4018T100MDGJ
SMD,4x4mm1.2A 1.3A 10uH 150mΩ ±20% SMD,4x4mm Power Inductors ROHSTaiyo YudenPower InductorsFNR4012S470MT
SMD,4x4mm1.43Ω 47uH 500mA 500mA Magnetic Shielded Inductor ±20% SMD,4x4mm Power Inductors ROHScjiangPower InductorsMBR0540
SOD-123-55℃~+150℃ 1 Independent 20uA@40V 40V 5.5A 500mA 510mV@500mA SOD-123 Schottky Diodes ROHSonsemiSchottky DiodesNCD0805R1
LED0805-30℃~+85℃ 1.6V~2.6V 130° 195mcd 25mA 615nm~630nm 630nm 65mW Discrete Diode Red 0805 LED Indication - Discrete ROHSFoshan NationStar OptoelectronicsLED Indication - Discrete
Parts
66| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 1uF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6, C7, C8, C9, C10, C14 |
| 6 | D_TVS | Diode_SMD:D_SOD-323 | D9, D10, D11, D12, D13, D14 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R4, R7, R8, R9, R10 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_ISO7380 | H1, H2, H3, H4 |
| 4 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1, SW2, SW3, SW4 |
| 3 | MBR0530 | Diode_SMD:D_SOD-123 | D1, D2, D3 |
| 2 | 1.5K | Resistor_SMD:R_0603_1608Metric | R6, R11 |
| 2 | 220nF | Capacitor_SMD:C_0603_1608Metric | C12, C16 |
| 2 | 4.7uF/25V | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 4.7uF/50V | Capacitor_SMD:C_0805_2012Metric | C11, C13 |
| 2 | GREEN | LED_SMD:LED_0805_2012Metric | D5, D7 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1, JP2 |
| 2 | ~ | MH_connectors:AFC24-S06FIA-00 | FL1, TS1 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 10uH | Inductor_SMD:L_Taiyo-Yuden_NR-40xx | L2 |
| 1 | 13.3R | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 2.2R | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 220R | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 47uH 500mA | Inductor_SMD:L_Changjiang_FNR4012S | L1 |
| 1 | Conn_02x14_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x14_P2.54mm_Vertical_SMD | J1 |
| 1 | DS18B20Z | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | LD2412 | MH_ics:LD2412 | U6 |
| 1 | LTR-303ALS-01 | OptoDevice:Lite-On_LTR-303ALS-01 | U2 |
| 1 | MBR0540 | Diode_SMD:D_SOD-123 | D4 |
| 1 | RED | LED_SMD:LED_0805_2012Metric | D8 |
| 1 | SHT4x | Sensor_Humidity:Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad | U4 |
| 1 | SK6812MINI | LED_SMD:LED_SK6812MINI_PLCC4_3.5x3.5mm_P1.75mm | D6 |
| 1 | Si1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70 | Q1 |
| 1 | TPS61165DBV | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1 |
| 1 | ~ | MH_connectors:AFC24-S24FIA-00 | P1 |
The 64 most common of 66 parts.
More from mckay27/hstat
1- 2 layers100 × 103.5 mm

Similar boards
- 2 layers45 × 95 mm

Airquality
MorgenWebDigital/airquality
A battery-powered indoor air quality monitor. Real CO₂ from a photoacoustic sensor, VOC and NOx, temperature, humidity and ambient light, shown on a 2.13" e-paper display and sent over Bluetooth LE.
78 parts - 2 layers75 × 140 mm

- 4 layers30 × 40 mm

- 4 layers35.9 × 43.1 mm

- 4 layers68.6 × 53.3 mm

- 2 layers54.6 × 61 mm

- 2 layers65 × 75 mm

- 2 layers52 × 36 mm

CyphalPicoBase CAN
generationmake/CyphalPicoBase-CAN
Board for the Raspberry Pi Pico to connect via CAN using OpenCyphal and UCANPHY Micro
62 parts5CERN-OHL-W-2.0
Questions
How big is the Display board PCB?
It measures 100 × 103.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Display board use?
66 parts, built around the DS18B20Z, LTR-303ALS-01, SHT41-AD1B-R2 and TPS61165DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Display board KiCad files?
From the mckay27/hstat repository on GitHub, at the commit this page was made from: the board is HW/display_board/display_board.kicad_pcb and its schematic HW/display_board/display_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Display board design in my own project?
Its repository states no licence, so its author keeps all rights: ask mckay27 before reusing the design.