Skip to the content
123456

TPS61165DBV

Texas InstrumentsExtended

-40℃~+85℃ 1 1.2A 1.2MHz 2% 3V~18V 3V~38V Boost Built-in DC-DC Over Voltage Protection、Over-Temperature Protection (OTP) PWM SOT-23-6 LED Drivers ROHS

Part id
ti/TPS61165DBV
Category
LED Drivers
Package
SOT-23-6
Pins
6
In stock
23,257 at JLCPCB (C58756)
Used on
15 open-source boards

Overview

The TPS61165DBV is a LED Driver made by Texas Instruments in a SOT-23-6 package with 6 pins. -40℃~+85℃ 1 1.2A 1.2MHz 2% 3V~18V 3V~38V Boost Built-in DC-DC Over Voltage Protection、Over-Temperature Protection (OTP) PWM SOT-23-6 LED Drivers ROHS.

PCBKit's library has its KiCad symbol (Driver_LED:TPS61165DBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 23,257 are in stock at JLCPCB (part C58756). 15 open-source boards in 15 repositories on GitHub use it.

Symbol

1VIN2CTRL3SW4GND5COMP6FB
Driver_LED:TPS61165DBVFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

14
Supply, least
3 V · VIN, recommended operating min · p. 4
Supply, most
18 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
20 V · VIN, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
85 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature absolute max · p. 4
Takes working
2.3 mA · VIN operating quiescent current max, PWM switching no load · p. 5
Takes asleep
1 µA · Shutdown current max, CRTL=GND, VIN = 4.2 V · p. 5
Feedback reference
200 mV · Feedback regulation voltage typical · p. 5
Switches at
1.2 MHz · Oscillator frequency typical · p. 5
Current limit
1.2 A · Switch current limit typical, D = Dmax · p. 5
Junction to air (DBV (SOT-23))
210.1 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DBV (SOT-23))
46.8 K/W · Junction-to-case(top) thermal resistance · p. 4
Junction to board (DBV (SOT-23))
56.7 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

4
Open LED protection
38 V · p. 1
Reference voltage accuracy
2% · p. 1
Brightness control
Enable, PWM and digital dimming through CTRL · p. 3
Package
6-Pin SOT-23, DBV · p. 3

Around it

6
cap 220 nF
between COMP and GND; Ceramic compensation capacitor, suitable for most applications. · p. 11
cap 1 μF minimum
between VIN and GND; Recommended input capacitor. · p. 4
cap 1–10 μF
between VOUT and GND; Recommended output capacitor. · p. 4
ind 10–22 μH
between VIN and SW; Recommended inductor range. · p. 4
diode ONsemi MBR0540 or ZETEX ZHCS400
between SW and VOUT; Schottky rectifier; reverse breakdown must exceed open LED protection voltage. · p. 11
res 15 kΩ
between CTRL and VIN; Pull-up for open-drain EasyScale acknowledge output. · p. 6

Specifications

63
ParameterConditionsAs printedPage
Supply voltages on VIN VINWith respect to network ground pinmin -0.3 · max 20 V4
Voltages on CTRL VINWith respect to network ground pinmin -0.3 · max 20 V4
Voltage on FB and COMP VINWith respect to network ground pinmin -0.3 · max 3 V4
Voltage on SW VINWith respect to network ground pinmin -0.3 · max 40 V4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Input voltage range, VIN VImin 3 · max 18 V4
Output voltage range VOMinimum = VINmax 38 V4
Inductor Lmin 10 · max 22 uH4
PWM dimming frequency fdimmin 5 · max 100 kHz4
Input capacitor CINmin 1 uF4
Output capacitor COmin 1 · max 10 uF4
Operating ambient temperature TAmin -40 · max 85 °C4
Operating junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADBV (SOT-23), 6 PINStyp 210.1 °C/W4
Junction-to-case(top) thermal resistance RθJC(top)DBV (SOT-23), 6 PINStyp 46.8 °C/W4
Junction-to-board thermal resistance RθJBDBV (SOT-23), 6 PINStyp 56.7 °C/W4
Junction-to-top characterization parameter ψJTDBV (SOT-23), 6 PINStyp 0.5 °C/W4
Junction-to-board characterization parameter ψJBDBV (SOT-23), 6 PINStyp 50.2 °C/W4
Operating quiescent current into VIN IQDevice PWM switching no loadmax 2.3 mA5
Shutdown current ISDCRTL=GND, VIN = 4.2 Vmax 1 uA5
Undervoltage lockout threshold UVLOVIN fallingtyp 2.2 · max 2.5 V5
Undervoltage lockout hysterisis Vhystyp 70 mV5
CTRL logic high voltage V(CTRLh)VIN = 3 V to 18 Vmin 1.2 V5
CTRL logic low voltage V(CTRLl)VIN = 3 V to 18 Vmax 0.4 V5
CTRL pull down resistor R(CTRL)min 400 · typ 800 · max 1600 kΩ5
CTRL pulse width to shutdown toffCTRL high to lowmin 2.5 ms5
Easy Scale detection time tes_detCTRL pin lowmin 260 us5
Easy Scale detection delay tes_delaymin 100 us5
Easy Scale detection window time tes_winMeasured from CTRL highmin 1 ms5
Voltage feedback regulation voltage VREFmin 196 · typ 200 · max 204 mV5
Voltage feedback regulation voltage under brightness control V(REF_PWM)VFB = 50 mVmin 47 · typ 50 · max 53 mV5
Voltage feedback regulation voltage under brightness control V(REF_PWM)VFB = 20 mVmin 17 · typ 20 · max 23 mV5
Voltage feedback input bias current IFBVFB = 200 mVmax 2 uA5
Oscillator frequency fSmin 1 · typ 1.2 · max 1.5 MHz5
Maximum duty cycle DmaxVFB = 100 mVmin 90 · typ 93 %5
Minimum on pulse width tmin_ontyp 40 ns5
Comp pin sink current Isinktyp 100 uA5
Comp pin source current Isourcetyp 100 uA5
Error amplifier transconductance Geamin 240 · typ 320 · max 400 umho5
Error amplifier output resistance Reatyp 6 MΩ5
Error amplifier crossover frequency fea5 pF connected to COMPtyp 500 kHz5
N-channel MOSFET on-resistance RDS(ON)VIN = 3.6 Vtyp 0.3 · max 0.6 Ω5
N-channel MOSFET on-resistance RDS(ON)VIN = 3.0 Vmax 0.7 Ω5
N-channel leakage current ILN_NFETVSW = 35 V, TA = 25°Cmax 1 uA5
N-Channel MOSFET current limit ILIMD = Dmaxmin 0.96 · typ 1.2 · max 1.44 A5
Start up current limit ILIM_StartD = Dmaxtyp 0.7 A5
Time step for half current limit tHalf_LIMtyp 5 ms5
Open LED protection threshold VovpMeasured on the SW pinmin 37 · typ 38 · max 39 V5
Open LED protection threshold on FB V(FB_OVP)Measured on the FB pin, percentage of Vref, Vref = 200 mV and 20 mVtyp 50 %5
VREF filter time constant tREFtyp 180 us5
VREF ramp up time tstepEach step, Measured as number of cycles of the 1.2-MHz clocktyp 213 us5
Thermal shutdown threshold Tshutdowntyp 160 °C5
Thermal shutdown threshold hysteresis Thysteresistyp 15 °C5
Start time of program stream tstartEasyScalemin 2 us6
End time of program stream tEOSEasyScalemin 2 · max 360 us6
High time low bit tH_LBLogic 0min 2 · max 180 us6
Low time low bit tL_LBLogic 0; minimum = 2 × tH_LBmax 360 us6
High time high bit tH_HBLogic 1; minimum = 2 × tL_HBmax 360 us6
Low time high bit tL_HBLogic 1min 2 · max 180 us6
Acknowledge output voltage low VACKNLOpen drain, Rpullup =15 kΩ to VINmax 0.4 V6
Acknowledge valid time tvalACKNSee (1); acknowledge active 0, RFA bit setmax 2 us6
Duration of acknowledge condition tACKNSee (1); acknowledge active 0, RFA bit setmax 512 us6

Pins, by the datasheet

6
1 VIN
Input supply; connect to a supply between 3 V and 18 V. · p. 3
2 CTRL
Multifunction control pin for enable, PWM and digital dimming. · p. 3
3 SW
Switching node; connect the switched side of the inductor here; also senses output voltage for open LED protection. · p. 3
4 GND
Ground. · p. 3
5 COMP
Transconductance error amplifier output; connect an external capacitor to compensate the converter. · p. 3
6 FB
Current feedback pin; connect the sense resistor from FB to GND. · p. 3

Ordering codes, by the datasheet

1
TPS61165DBV
DBV (SOT-23), 6 pins · –40°C to 85°C; 38 V typical open LED protection; package marking DAK. · p. 3

Open-source boards using it

15See all 15
  • 2 layers75 × 140 mmBadge, the printed circuit board in 3D

    Badge

    mmicko/workshop_badge

    Proposal for FPGA workshop badge for Hackaday Belgrade 2018

    45 parts10
  • 2 layers65 × 56 mmPigmice led ring, the printed circuit board in 3D

    Pigmice led ring

    Pigmice2733/gloworm

    Original Gloworm design for an RPi 4

    39 parts8
  • 6 layers146.1 × 58.4 mmComp Board, the printed circuit board in 3D

    Comp Board

    badaboombox/SS-Handheld-Console

    An open-source handheld game console built around a Lattice ECP5 FPGA that uses a custom hybrid 2D + 3D graphics engine capable of DS-era 2D-and-3D gameplay at a locked 60 fps.

    248 parts6
  • 4 layers60 × 80 mmRpi mipi dsi display, the printed circuit board in 3D

    Rpi mipi dsi display

    chrispyy87/rpi-mipi-dsi-display

    Raspberry CM4/RP4 MIPI DSI display breakout board with drivers

    25 parts1
  • 4 layers30 × 40 mmPulsepatch, the printed circuit board in 3D

    Pulsepatch

    suhaant/Amethyst

    Full-Stack Embedded System Wearable

    90 parts1
  • 4 layers35.9 × 43.1 mmProx sensor, the printed circuit board in 3D

    Prox sensor

    cornway/vanity_mirror_pcb

    41 parts
  • 2 layers57 × 43 mmRbcrash, the printed circuit board in 3D

    Rbcrash

    onitake/rbcrash

    Remote controlled high power RGB LED lamp

    42 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS61165DBV?

Yes. The symbol is Driver_LED:TPS61165DBV and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS61165DBV?

SOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the TPS61165DBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS61165DBV?

JLCPCB lists it as part C58756, with 23,257 in stock; the sellers' links on this page open their listings.

What can replace the TPS61165DBV?

Parts like it in the library: the AP3032KTR-G1 by Diodes Incorporated, the AP3031KTR-G1 by Diodes Incorporated, the JW1121ASOTB#TRPBF by JoulWatt Tech and the TPS54200DDC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS61165DBV?

15 boards in 15 repositories on GitHub; the most starred are listed on this page, with their KiCad files.