
Kicad main
johannesstrueber/dots
DOTS eurorack module pcb schematics and code ATMega328 based

Blinky-328 is an open-source printed circuit board by matejcsok-pcb, from the matejcsok-pcb/Blinky-328 repository on GitHub. It is a 2-layer board of 55 × 42 mm with 25 parts on 33 nets, routed with 152 tracks and 8 vias.
It is built around the ATMEGA328P-AU and AMS1117-5.0. Its parts include 7 capacitors, 5 connectors, 3 resistors, 2 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | C | Capacitor_SMD:C_0603_1608Metric | C1, C4, C5, C6, C7 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | R | Resistor_SMD:R_0603_1608Metric | R1, R2, R3 |
| 2 | C | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3, J5 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D2 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |

johannesstrueber/dots
DOTS eurorack module pcb schematics and code ATMega328 based

jayanta525/dual-h-bridge
Dual H-Bridge Controller with IRF3205 and IR2104 MOSFET Driver, and with ATMega328P-AU PWM Controller

justraven/FlightController
Flight Controller PCB Design, Utilized ATMega328P. Compatible with MultiWii


M-S-Ali/raven-i-sentinel
6S - 24V - 20A Battery Management System (BMS) based on TI BQ76925 and Microchip Atmega328P.

wszeto9/2_679_PCB
PCB Project for 2.679 which is then used in my 2.007 Competition Robot

7bwiiza/Robot-creation
Uni project of a 3D model of a 5dof robot using Solidedge and motor control using KiCAD and MATLAB

BartekOrchowski/MiniSumoAVR
This project is a MiniSumo robot developed during a workshop organized by the KoNaR student scientific association.
It measures 55 × 42 mm and has 2 copper layers, 1.6 mm thick.
25 parts, built around the ATMEGA328P-AU and AMS1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the matejcsok-pcb/Blinky-328 repository on GitHub, at the commit this page was made from: the board is main.kicad_pcb and its schematic main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask matejcsok-pcb before reusing the design.