
3D Printer Mainboard STM32
m47812/Custom-3D-Printer-Controller
A fully custom 3D Printer controller board based on an stm32f7 controller with TMC2209 stepper drivers

A fully custom 3D Printer controller board based on an stm32f7 controller with TMC2209 stepper drivers
3D Printer Stepper TMC2209 is an open-source printed circuit board by m47812, from the m47812/Custom-3D-Printer-Controller repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 21 × 24 mm with 21 parts on 27 nets, routed with 227 tracks and 44 vias.
It is built around the TMC2209. Its parts include 10 capacitors, 7 resistors, 2 connectors, 1 IC and 1 diode. It belongs with the robots and motor control boards and the STM32 boards of this library.
A fully custom 3D Printer controller board based on a stm32f7 controller with TMC2209 stepper drivers
This Repo contains the design files for a fully custom 3D printer controller board. It is equipped with an STM32F7 Controller and uses custom-made TMC2209 Driver PCBs (also included in the Repo). The PCB was designed for using JLCPCBs Assembly service, so most of the SMD parts can directly be assembled by them. The Controller PCB is a two layer board, which makes production for hobby projects more affordable.
The Project contains 3 Folders with KiCad design files.
I designed this 3D printer controller as a hobby project, for my own 3D printer. The original plan was to build a custom hardware and custom firmware. Throughout the project my colleague and I have moved to a different printer design which resulted in the stop of the firmware project. The PCB was produced at JLCPCB and I did some tests with it. I've decided to make the project open source for anyone who would like to build their own 3D printer electronics. The project may serve as a starting point or something to enhance, modify and customize.
Since the project was not continued on the firmware side, I did not have the possibility of testing all features to a full degree. My tests manly focused on using the
the motor drivers together with the STM32. I haven't found any problems so far with the PCB, but I would advise looking over it yourself before you order it.
I would recommend using the board with Marlin firmware. It will require some manual adaptations to be able to use Marlin. Since I haven't used Marlin in my own project, I can not provide these adaptations here.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C102, C103, C106, C109 |
| 3 | 22n | Capacitor_SMD:C_0805_2012Metric | C101, C107, C108 |
| 2 | 100m | Resistor_SMD:R_2512_6332Metric | R105, R106 |
| 2 | 22u | Capacitor_SMD:C_0805_2012Metric | C104, C105 |
| 2 | Conn_01x09 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J101, J102 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R102 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R104 |
| 1 | 2.2u | Capacitor_SMD:C_0603_1608Metric | C110 |
| 1 | 20k | Resistor_SMD:R_0402_1005Metric | R103 |
| 1 | 220 | Resistor_SMD:R_0603_1608Metric | R107 |
| 1 | NC | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R101 |
| 1 | TMC2209 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm_ThermalVias | U101 |
| 1 | red | LED_SMD:LED_0603_1608Metric | D101 |

m47812/Custom-3D-Printer-Controller
A fully custom 3D Printer controller board based on an stm32f7 controller with TMC2209 stepper drivers

m47812/Custom-3D-Printer-Controller
A fully custom 3D Printer controller board based on an stm32f7 controller with TMC2209 stepper drivers

creapunk/CLN-ClosedLoopNemaDriver
Compact closed-loop stepper motor driver designed for NEMA motors


wntrblm/jellyfish-and-starfish
Jellyfish and Starfish are control boards designed for use with the LumenPnP. Starfish controls the base of the machine including X & Y axes and pneumatics.

NikodemBartnik/StarTrckr
Open source star tracker for deep sky astrophotography
RParkerE/OpenSilicon
OpenSilicon enables DIY semiconductor fabrication with open-source guides for building IC equipment at home. The project includes BOMs, 3D files, firmware, and PDKs, supporting makers and researchers in chip fabrication.

AdamTuraj/PicoMMU
A Klipper expansion board intended to run a MMU unit to control a stepper motor and servo.

TheContrappostoShop/Apollo
Control Board for the Prometheus mSLA Printer.

Duet3D/Duet3-Mini5plus
This repository also contains information in the Mini 2+ : a two driver expansion board for the Duet 3 mini 5+
It measures 21 × 24 mm and has 2 copper layers, 1.6 mm thick.
21 parts, built around the TMC2209. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the m47812/Custom-3D-Printer-Controller repository on GitHub, at the commit this page was made from: the board is 3D_Printer_Motor_Driver/3D_Printer_Stepper_TMC2209.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).