
Mainboard-2023
luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

The eletronics projects of our robots and basestation.
Kabeltester v2 is an open-source printed circuit board by luhbots, from the luhbots/luhsoccer_electronics repository on GitHub. It is a 2-layer board of 66 × 81 mm with 67 parts on 82 nets, routed with 739 tracks and 122 vias.
It is built around the RP2040, W25Q128JVSIQ and 74HC4051, with the WS2812B and BSD840NH6327XTSA1 among its other parts. Its parts include 18 resistors, 16 capacitors, 12 diodes, 5 ICs and 5 connectors. It belongs with the RP2040 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5, C6, C8, C10, C11, C12, C13, C14, C15, C17 |
| 8 | 20 | Resistor_SMD:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R22, R23, R24, R25, R26, R27, R28, R29 |
| 8 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D2, D3, D4, D5, D6, D7, D8, D9 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C4, C7, C9 |
| 4 | BSD840NH6327XTSA1 | Package_TO_SOT_SMD:SOT-363_SC-70-6_Handsoldering | Q1, Q2, Q3, Q4 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2, H3, H4 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4, R6, R8 |
| 3 | LED_Grün | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D10, D11, D12 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R7 |
| 2 | 27,4 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R5 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C3 |
| 2 | 470 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R11 |
| 2 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1, SW2 |
| 1 | 220 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9 |
| 1 | 74HC4051 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U3 |
| 1 | AP1117-33 | Package_TO_SOT_SMD:SOT-23 | U6 |
| 1 | Conn_01x03_Button | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Conn_01x03_Debug | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Conn_01x04_I2C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_02x06_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x06_P2.54mm_Vertical | J2 |
| 1 | Crystal_GND24_12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | LED_Rot | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | LF25_TO252 | Package_TO_SOT_SMD:TO-252-2 | U4 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U5 |

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.


luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

luhbots/luhsoccer_electronics
The eletronics projects of our robots and basestation.

ansemjo/pi2co-usb
USB to I2C bridge using an Atmel AVR ATtiny85V and even more tiny than I2C-Tiny-USB.



ansemjo/chronovfd
hardware project for a clock around a russian ivl2-5/7 vfd and an esp32-wroom module
michaelswitzer/granola-beacon
Granola Beacon: arcade controller with hall effect switches


Twisted-Fields/rp2040-motor-controller
A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.

ph-design/PH60-SC
A printable low-profile 60% wireless mechanical keyboard kit powered by ZMK firmware.
It measures 66 × 81 mm and has 2 copper layers, 1.6 mm thick.
67 parts, built around the RP2040, W25Q128JVSIQ, 74HC4051 and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the luhbots/luhsoccer_electronics repository on GitHub, at the commit this page was made from: the board is Wiretester/Kabeltester_v2.kicad_pcb and its schematic Asterix/ControlUnit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask luhbots before reusing the design.