

Midi sync module
The MIDI-sync-power-dev-board is a 4hp eurorack module allowing you to get an isolated 5V, 3.3V from LDO, a sync in from 3.5mm jack and either midi input or midi output. The goal is to use it as expander for other module or use it when developping new modules
- Size
- 20 × 108 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 41
- Nets
- 33
- Pads
- 126
- Tracks, vias
- 231, 29
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 21 May 2023
- Updated
- 21 May 2023
Overview
Midi sync module is an open-source printed circuit board by lucblender, from the lucblender/MIDI-sync-power-dev-board repository on GitHub, published under the MIT licence. It is a 2-layer board of 20 × 108 mm with 41 parts on 33 nets, routed with 231 tracks and 29 vias.
It is built around the ISU0205S05-TR, ADP7142AUJZ-3.3-R7 and US1B, with the MMBT3904 among its other parts. Its parts include 10 resistors, 9 capacitors, 5 diodes, 5 connectors and 3 ICs. It belongs with the audio and music and microcontroller boards boards of this library.
Main components
4ISU0205S05-TR
SMD-7P,19.1x15mm1 4.5V~12V 400mA 5V 79% SMD-7P,19.1x15mm DC-DC Power Modules ROHSXP PowerDC-DC Power ModulesADP7142AUJZ-3.3-R7
TSOT-23-5-40℃~+125℃@(Ta) 1 11uVrms 200mA 200mV@(200mA) 3.3V 40V 50uA 88dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Soft Start、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAnalog DevicesVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUS1B
SMA-65℃~+150℃ 100V 1A 1V@1A 50ns 5uA SMA Fast Recovery / High Efficiency Diodes ROHSDiodes IncorporatedFast Recovery / High Efficiency DiodesMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdMIDI-sync-power-dev-board
The MIDI-sync-power-dev-board is a 4hp eurorack module created to be used either as an expander for other board or as a standalone module helping you developping electronic. The module provides :
- an isolated 5V 400mA
- a 3.3V 200mA from LDO
- a Sync in from 3.5mm jack (use as sync, gate, trigger, ...)
- 0-xV signal input transformed to TTL level (signal is inverted)
- a MIDI input or MIDI output configurable through soldering jumper
- Can only use one configuration at a time!
The module has a 2x a 10 pins header on top and bottom that gives you access to eurorack +12V and -12V, the board 5V and 3.3V, the Sync signal, the MIDI in or MIDI out signal.
| Signal names | |
|---|---|
| +5V | +3.3V |
| +12V | -12V |
| GND | GND |
| MIDI OUT | GND |
| Sync IN | MIDI IN |
The idea behind this module came while developping my own synth that needed MIDI input. I had to make my own little MIDI In through optocoupler on breadboard or veroboard each time.
Additonally, I created the Canvas synthesizer in collaboration with Synthux Academy. And the board did not have MIDI input or sync in making it hard to sync with any synthesizer setup. To not add complexity to the design, I prefered to create this little expander that I now use to power the Canvas and use Sync in and MIDI input.
Schematic

PCB
| Top | Bottom |
|---|---|
![]() | ![]() |
MIDI configuration
| MIDI in | MIDI out |
|---|---|
| On the bottom, you need to solder JP1 and JP2 | On the top, you need to solder JP3, JP4 and JP5 |
Reminder: You can only use one MIDI configuration at a time!
Front panel
The MIDI-sync-power-dev-board has mutliple front panel since it can be use for various reason.
- midi-sync-module-front-panel-a: Dedicated to the Canvas
- midi-sync-module-front-panel-b: Generic Sync In, MIDI OUT
- midi-sync-module-front-panel-c: Generic Sync In, MIDI IN
All the front panel are double sided. On the Top you will find a the debug front panel with 10 pins header description. And on the Bottom you will find the custom design.
Front Panel Example
| front-panel-a-top | front-panel-a-bottom | front-panel-b-top | front-panel-b-bottom | front-panel-c-top | front-panel-c-bottom |
|---|---|---|---|---|---|
![]() | TODO | ![]() | ![]() | ![]() | ![]() |
Parts
41| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP2, JP3, JP4, JP5 |
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C5, C7 |
| 3 | 10uF | Capacitor_SMD:CP_Elec_6.3x5.9 | C3, C4, C6 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R8 |
| 2 | 2.2u | Capacitor_SMD:C_0805_2012Metric | C8, C9 |
| 2 | 330 | Resistor_SMD:R_0805_2012Metric | R9, R10 |
| 2 | FerriteBead | Inductor_SMD:L_0805_2012Metric | FB1, FB2 |
| 2 | LED | LED_THT:LED_D3.0mm | D4, D5 |
| 2 | US1B | Diode_SMD:D_SMA | D1, D2 |
| 1 | 10 | Resistor_SMD:R_0805_2012Metric | R7 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 1N4148 | Diode_SMD:D_SOD-123 | D3 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 220 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 30 | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 6N137 | Package_DIP:SMDIP-8_W9.53mm | U2 |
| 1 | ADP7142AUJZ-3.3 | Package_TO_SOT_SMD:TSOT-23-5 | U3 |
| 1 | AudioJack2_SwitchT | AudioJacks:Jack_3.5mm_QingPu_WQP-PJ301BM_Vertical | J1 |
| 1 | Conn_01x10_Male | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J2 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_SMD | J4 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Horizontal | J5 |
| 1 | DIN-5_180degree | SD-50BV:CUI_SD-50BV | J3 |
| 1 | ISU0205S05 | Converter_DCDC:Converter_DCDC_XP_POWER-ISU02_SMD | U1 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1 |
The 40 most common of 41 parts.
Similar boards
- 2 layers54 × 57 mm

- 4 layers96 × 172 mm

- 2 layers119.9 × 108 mm

Lx deciim
lucblender/lx-deciim
lx-deciim is a dual-channel bitcrusher Eurorack module based on the Daisy Seed. Unlike traditional bitcrushers, it lets you selectively disable bits and replace them with CV-controlled triggers.
206 parts5 - 2 layers9.8 × 110 mm

2hp simple switch button
lucblender/lx-sw-btn
The "lx-sw-btn": a 2HP eurorack module with 4 customizable switches enabled CV outputs!
37 parts1MIT - 2 layers104.1 × 79.4 mm

- 4 layers178 × 83.3 mm

- 4 layers80 × 49 mm

- 2 layers78 × 61 mm

Questions
How big is the Midi sync module PCB?
It measures 20 × 108 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Midi sync module use?
41 parts, built around the ISU0205S05-TR, ADP7142AUJZ-3.3-R7, US1B and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Midi sync module KiCad files?
From the lucblender/MIDI-sync-power-dev-board repository on GitHub, at the commit this page was made from: the board is hardware/midi-sync-module/midi-sync-module.kicad_pcb and its schematic hardware/midi-sync-module-front-panel-a/midi-sync-module-front-panel-a.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Midi sync module design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).






