Skip to the content
2 layers100 × 100 mmDrone v2-systemboard notrace, the printed circuit board in 3D

Drone v2-systemboard notrace

lucaspcamargo/hydrus-v2

Second version of the Hydrus project: sw, hw, docs, etc. (RaspberryPi based)

Size
100 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
61
Nets
64
Pads
266
Tracks, vias
0, 0
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
3 Aug 2018
Updated
25 Jun 2026

Overview

Drone v2-systemboard notrace is an open-source printed circuit board by lucaspcamargo, from the lucaspcamargo/hydrus-v2 repository on GitHub. It is a 2-layer board of 100 × 100 mm with 61 parts on 64 nets.

It is built around the ATMEGA328-PU, AD8603AUJ and BC547. Its parts include 23 connectors, 15 resistors, 6 capacitors, 6 diodes and 3 ICs. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

3

README

README.md

Hydrus v2

Hydrus is an autonomous surface vehicle for water quality measurement. The original v1 platform won first place at the Intel Embedded Systems Competition 2016. This repository contains v2: a ground-up retool of the vehicle firmware and hardware, now running on a Raspberry Pi Zero W atop a custom backbone board.

The vehicle navigates a body of water along a pre-planned route, stops at designated waypoints to collect sensor readings, and streams data in real time to a Qt5-based base station running on a laptop.

The project spans embedded firmware, base station software, custom PCB hardware design, and 3D-printed mechanical components.

Hydrus on the water

Hydrus during field testing on a lake in Joinville, 2016.

Hardware

The vehicle runs on a Raspberry Pi Zero W with a custom backbone board that integrates all peripherals:

  • GPS: u-blox NEO-6 for position and speed
  • IMU: HMC5883L 3-axis magnetometer for heading
  • ADC: ADS1115 16-bit I2C ADC multiplexing four analog channels
  • Water sensors: pH probe, TMP36 temperature sensor, TSD-10 turbidity sensor
  • Propulsion: dual brushed motors with PWM speed control (differential drive)
  • Power: LiPo battery with voltage monitoring

Custom Hydrus System Board with GPS antenna and pH probe

The custom Hydrus v2 System Board, with GPS antenna and pH probe.

Hardware design files (KiCad schematics and layouts) are in hw/. Mechanical parts (propellers, axle adapters, board mounts) are 3D-printable models in mech/.

Firmware

The vehicle firmware (fw/) is written in C++11 and built with CMake. It runs four concurrent periodic tasks:

TaskRateResponsibility
SystemTask2 HzState machine, battery/thermal monitoring, shutdown
SensingTask30 HzpH, temperature, turbidity, IMU heading
NavigationTask10 HzGPS, motor control, waypoint tracking
CommTask20 HzTCP link to base station, command routing

All tasks share a double-buffered blackboard with reader-writer locking, which eliminates contention between producers and consumers without blocking.

Navigation

Autonomous navigation follows a state machine: align to bearing → traverse toward waypoint → acquire data → advance to next waypoint. Distance and bearing use the Haversine formula and forward azimuth calculation against WGS-84 coordinates. Speed is throttled adaptively as the vehicle closes in on a waypoint.

A remote-control mode is also supported, accepting velocity vectors from the base station for manual operation.

Base Station

Base station software showing a live mission on the map

Base station software showing a live mission on the map.

The base station (station/) is a Qt5/C++ desktop application featuring:

  • Live map via the Marble widget, showing vehicle position, heading, trail, and waypoints over OpenStreetMap tiles
  • Route editor for building multi-waypoint missions with per-waypoint acquire flags
  • Real-time dashboard for sensor readings, system state, and battery level
  • Log viewer with streaming from the vehicle and timeline-based replay
  • RC control widget with joystick/gamepad support

Communication uses a TCP socket (port 6666). The vehicle streams binary blackboard snapshots and log messages; the base station sends text commands.

Repository layout

text
doc/      Documentation and branding (including competition presentation)
fw/       Vehicle firmware (C++11, CMake)
lib/      Shared libraries
station/  Base station software (Qt5, C++11)
hw/       PCB schematics and layouts (KiCad)
mech/     3D-printable mechanical components

Credits

The original Hydrus project was developed at Universidade Federal de Santa Catarina. Team members: Guilherme Augusto Pangratz and Emili Bohrer. Mentored by Prof. Dr. Giovani Gracioli.

Parts

61
QtyValueFootprintReferences
44.7kResistors_SMD:R_0805_HandSolderingR10, R11, R12, R13
4DDiodes_SMD:D_SOD-123D2, D6, D7, D8
20RResistors_SMD:R_1210_HandSolderingR16, R17
21kResistors_SMD:R_0805_HandSolderingR6, R7
222pFCapacitors_SMD:C_0805_HandSolderingC1, C2
1.1uCapacitors_SMD:C_0805_HandSolderingC6
10.47ufCapacitors_SMD:C_0805_HandSolderingC3
11.5kResistors_SMD:R_0805_HandSolderingR8
110KResistors_SMD:R_0805_HandSolderingR1
110uFCapacitors_Tantalum_SMD:CP_Tantalum_Case-S_EIA-3216-12_HandC5
11KResistors_SMD:R_0805_HandSolderingR2
11mHInductors:Inductor_1212L1
1300RResistors_SMD:R_0805_HandSolderingR3
1470RResistors_SMD:R_0805_HandSolderingR9
147kResistors_SMD:R_0805_HandSolderingR14
16.4kResistors_SMD:R_0805_HandSolderingR15
166ufCapacitors_SMD:C_0805_HandSolderingC4
1AD8603TO_SOT_Packages_SMD:TSOT-23-5_HandSolderingU2
1ADC_MODULEPin_Headers:Pin_Header_Straight_1x10_Pitch2.54mmP9
1ADR1581TO_SOT_Packages_SMD:SOT-23Q3
1ATMEGA328-PHousings_DIP:DIP-28_W7.62mmIC1
1AUX_ADCPin_Headers:Pin_Header_Straight_1x04_Pitch2.54mmP15
1AUX_ADC_GNDPin_Headers:Pin_Header_Straight_1x01_Pitch2.54mmP19
1AUX_ICSP_SERIALPin_Headers:Pin_Header_Straight_1x06_Pitch2.54mmP10
1AUX_P1Pin_Headers:Pin_Header_Straight_1x08_Pitch2.54mmP17
1AUX_P2Pin_Headers:Pin_Header_Straight_1x08_Pitch2.54mmP16
1AUX_UARTPin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmP18
1BATTConnect:AK300-2P8
1BC547TO_SOT_Packages_THT:TO-92_Inline_WideQ2
1EMOTE3_EXP1emote3:HEADER_18x1_EMOTEP1
1EMOTE3_EXP2emote3:HEADER_18x1_EMOTEP2
1ESC_LPin_Headers:Pin_Header_Straight_1x03P4
1ESC_L_PWRConnect:AK300-2P6
1ESC_RPin_Headers:Pin_Header_Straight_1x03P5
1ESC_R_PWRConnect:AK300-2P7
1GPIO_EXTPin_Headers:Pin_Header_Straight_1x04_Pitch2.54mmP21
1GPS_VDD_selPin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmP14
1GPS_modulePin_Headers:Pin_Header_Straight_1x05_Pitch2.54mmP13
1H2O_temp_turbPin_Headers:Pin_Header_Straight_1x06_Pitch2.54mmP12
1LEDLEDs:LED-5MMD1
1LM3940TO_SOT_Packages_SMD:SOT-223-3Lead_TabPin2U1
1LOGOhydrus:hydrus_logo_8mmG***
1L_AUX_PLEDs:LED_0805D3
1MAG_MODULEPin_Headers:Pin_Header_Straight_1x05_Pitch2.54mmP20
1OSHW-Symbol_6.7x6mm_SilkScreenSymbols:OSHW-Symbol_6.7x6mm_SilkScreenOSW
1PH_INConnect:BNCP11
1PWR_OUTPin_Headers:Pin_Header_Straight_2x03_Pitch2.54mmP22
1PWR_SWConnect:AK300-2SW1
1SPI_OUTPin_Headers:Pin_Header_Straight_1x05_Pitch2.54mmP23
1WEEE-Logo_4.2x6mm_SilkScreenSymbols:WEEE-Logo_4.2x6mm_SilkScreenWEEE
1XT_AUX_16MCrystals:Crystal_HC49-U_VerticalY1
1rbpiPin_Headers:Pin_Header_Straight_2x20P3

Similar boards

  • 2 layers42 × 42 mmNEW PCB ADCS, the printed circuit board in 3D

    NEW PCB ADCS

    niki100jad/POQUITO_ADCS

    ADCS for a PocketQube mission (Warning: Still untested!)

    82 parts2
  • 6 layers100.7 × 106.4 mmSignal processing unit, the printed circuit board in 3D

    Signal processing unit

    scalinq-lab/cryomagsens

    The sensor unit was designed in KiCad 10 and manufactured by JLCPCB. It is built in a flex PCB material to achieve a very small build height, in order to come very close to the device under test.

    178 parts2CERN-OHL-P-2.0
  • 2 layers95.9 × 27.8 mmOpsx x, the printed circuit board in 3D

    Opsx x

    ZeshuLiu/SX-70-Mk2

    把板子上的U+ U- GND VCC焊到usb线上,连接电脑后可以当作树莓派Pico开发板进行操作,上传代码的参见这里(树莓派官网)。 \ 在将机身主控安装至机器内部之前需要将micropython固件及代码烧录至控制器中。后续可以通过机身控制器上的USB接口连接开发板并更新python代码。 将code根目录中的所有python文件上传至控制器(文件夹不需要),并且将gmain.py命名为…

    74 parts2GPL-3.0
  • 4 layers30 × 40 mmPulsepatch, the printed circuit board in 3D

    Pulsepatch

    suhaant/Amethyst

    Full-Stack Embedded System Wearable

    90 parts1
  • 2 layers28.1 × 34 mmVibeLight, the printed circuit board in 3D

    VibeLight

    ArjunD112/VibeLight

    Personal PCB Project

    42 parts
  • 4 layers34.8 × 69.6 mmEnokiEEG v2, the printed circuit board in 3D

    EnokiEEG v2

    io-tronic/EnokiEEG

    This project funded in part by the Russell Foundation

    93 parts
  • 2 layers90.5 × 104.4 mmRP spectroscopy, the printed circuit board in 3D

    RP spectroscopy

    SimoneDamian/RP_Spectroscopy_kicad

    Circuits for the hardware part of the project

    96 parts

Questions

How big is the Drone v2-systemboard notrace PCB?

It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Drone v2-systemboard notrace use?

61 parts, built around the ATMEGA328-PU, AD8603AUJ and BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Drone v2-systemboard notrace KiCad files?

From the lucaspcamargo/hydrus-v2 repository on GitHub, at the commit this page was made from: the board is hw/drone-v2-systemboard/drone-v2-systemboard-notrace.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Drone v2-systemboard notrace design in my own project?

Its repository states no licence, so its author keeps all rights: ask lucaspcamargo before reusing the design.