

20x20 fc
Open source flight controller based on the STM32F405 MCU that runs betaflight.
- Size
- 40 × 40 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 120
- Nets
- 100
- Pads
- 384
- Tracks, vias
- 881, 112
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 24 Mar 2026
- Updated
- 17 Oct 2026
Overview
20x20 fc is an open-source printed circuit board by lmiez, from the lmiez/yecnodF405 repository on GitHub, published under the GPL-3.0 licence. It is a 6-layer board of 40 × 40 mm with 120 parts on 100 nets, routed with 881 tracks and 112 vias.
It is built around the MP4420GJ-P, MAX7456EUI and W25Q128JVPIQ, with the MS561101BA03-50, LDL212PV33R and ICM-42688-P among its other parts. Its parts include 40 capacitors, 31 resistors, 8 ICs, 8 diodes and 2 connectors. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
8MP4420GJ-P
TSOT-23-8-40℃~+125℃@(TJ) 1 2A 410kHz 4V~30V Adjustable Buck Buck Built-in Yes TSOT-23-8 DC-DC Converters ROHSMonolithic Power SystemsDC-DC ConvertersMAX7456EUI
TSSOP-28-EPNon-volatile configuration storage TSSOP-28-EP Video Interface ICs ROHSAnalog DevicesVideo Interface ICsW25Q128JVPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 120ms@(32KB) 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASHMS561101BA03-50
QFN-8(3x5)-40℃~+85℃ 1.8V~3.6V 140nA 150pa 1Kpa~1.2bar 8.22ms I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output Yes QFN-8(3x5) Pressure Sensors ROHSTE ConnectivityPressure SensorsLDL212PV33R
DFN-6(2x2)-40℃~+125℃@(Tj) 1 1.2A 18V 250uA 3.3V 600mV@(1.2A) 60uVrms 87dB@(120Hz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable DFN-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsICM-42688-P
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps Motion Event Detection, Synchronization, Timestamp Support LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometersNANOT240AS
SMD-40℃~+85℃ 0.55mm 15V 2.1mm 2.4N 200,000 cycles 20mA IP57 Round Button SMD(SMT) Tab SPST-NO Surface Mount,Vertical SMD Tactile Switches ROHSC&KTactile SwitchesSMBJ28A
DO-214AA(SMB)-55℃~+150℃ 13.2A 28V 31.1V 45.4V 5uA 600W TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHSGOODWORKESD And Surge Protection (TVS/ESD)
README
README.mdyecnod F405 V1.1
Description
open-source (not that anyone would want to use it) 40x40 F405 Flight controller using betaflight software.
Features
- 3 Universal UARTS
- Dedicated pads for analog VTX
- 9V and 5V Buck converters
- 2x 3.3V LDOS
- Integrated barometer
- LDO and Buck converter status LEDS
- 16MB Blackbox flash
- Full betaflight support
- ICM 42688-P (kind of a flex with how hard they are to get nowadays)
- 4V5 Pads for RX
This is the first revision of the yecnodF405 so expect more features on the 2nd.
COST
- AROUND 60 USD PER PCB
- AROUND 30 USD FOR 5 PCBS
On my next revision I will try to cut the costs by atleast 40%
BOM
| NAME | PURPOSE | QTY | PRICE | LINK | |
|---|---|---|---|---|---|
| 1 | LCSC | PASSIVES/ALL IC'S | 1 | $73.43 | LINK |
| 2 | HOT AIR GUN | SOLDERING | 1 | $35 | LINK |
| 3 | MP4420 | BUCK CONVERTER (NOT AVAILABLE ON LCSC) | 10 | $7.7 | LINK |
| 4 | TWEEZERS | HELP FOR SOLDERING TINY 0402 | 2 | $16.5 | LINK LINK |
| 5 | FLUX | SOLDERING | 1 | $11.2 | LINK |
| 6 | C245 TIP | SOLDERING | 1 | $7 | LINK |
| 7 | JLCPCB | PCBS | 5 | $12.71 | LINK |
| 8 | TARIFFS | dumb eu laws | 1 | $41 |
Final prices for each website are available as screenshots on the macondo website. LCSC cart BOM is available as a csv. Total price for everything is 204.73 USD
Notes
- This is my 2nd ever electronics project (Although I made another 3 during the break I took on this project) so don't expect everything to be electrically sound, this has been a great learning experience though, even with all the headaches it gave me.
- The jlcpcb BOM is only partly complete since I've decided to not use PCBA (use at you own risk some parts may not be right)
Photos
Build Photos
Parts
120| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C6, C13, C14, C23, C25, C26, C27, C30, C33, C34, C36, C37, C40 +2 |
| 5 | 100K | Resistor_SMD:R_0402_1005Metric | R4, R8, R19, R22, R28 |
| 5 | 4V5 | TestPoint:1.5mm pad | TP6, TP7, TP8, TP10, TP13 |
| 5 | GND | TestPoint:1.5mm pad | TP5, TP9, TP16, TP23, TP24 |
| 4 | 10K | Resistor_SMD:R_0402_1005Metric | R13, R26, R27, R30 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D4, D5, D6, D7 |
| 4 | MountingHole | MountingHole:MountingHole_4.3mm_M4 | H1, H2, H3, H4 |
| 3 | +5V | TestPoint:1.5mm pad | TP14, TP21, TP22 |
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric | C17, C29, C41 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C9, C18, C20 |
| 3 | 2u2 | Capacitor_SMD:C_0402_1005Metric | C1, C2, C24 |
| 3 | 4.7K | Resistor_SMD:R_0402_1005Metric | R12, R33, R34 |
| 2 | +9V | TestPoint:1.5mm pad | TP17, TP20 |
| 2 | 100nf | Capacitor_SMD:C_0402_1005Metric | C38, C39 |
| 2 | 15pF | Capacitor_SMD:C_0402_1005Metric | C10, C11 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric | R31, R32 |
| 2 | 20 | Resistor_SMD:R_0402_1005Metric | R5, R18 |
| 2 | 22 | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric | C15, C32 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C19, C21 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C12, C28 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R3, R36 |
| 2 | 75 | Resistor_SMD:R_0402_1005Metric | R24, R25 |
| 2 | D_Schottky | Diode_SMD:D_0603_1608Metric | D2, D3 |
| 2 | LDL212PV33R | EasyEDA:DFN-6_L2.0-W2.0-P0.50-BL-EP1.45 | U8, U9 |
| 2 | MP4420GJ-P | EasyEDA:TSOT-23-8_L2.9-W1.6-P0.65-LS2.8-BL | U4, U7 |
| 2 | SMHT4020-100MT | EasyEDA:IND-SMD_L4.0-W4.0_TNR4030S | L3, L4 |
| 1 | 1.5K | Resistor_SMD:R_0402_1005Metric | R29 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R35 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C22 |
| 1 | 12.4K | Resistor_SMD:R_0402_1005Metric | R20 |
| 1 | 150K | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 16Mhz | EasyEDA:CRYSTAL-SMD_4P-L2.0-W1.6-BL | Y1 |
| 1 | 18.7K | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 22.6K | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 27Mhz | EasyEDA:CRYSTAL-SMD_4P-L2.0-W1.6-BL | Y2 |
| 1 | 47 | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 470nF | Capacitor_SMD:C_0402_1005Metric | C35 |
| 1 | 47uF | Capacitor_SMD:C_1206_3216Metric | C42 |
| 1 | 680 | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 8.66K | Resistor_SMD:R_0402_1005Metric | R21 |
| 1 | CAM | TestPoint:1.5mm pad | TP15 |
| 1 | FerriteBead_Small | Inductor_SMD:L_0402_1005Metric | FB1 |
| 1 | ICM-42688-P | EasyEDA:LGA-14_L3.0-W2.5-P0.50-TL | U2 |
| 1 | LED GREEN | LED_SMD:LED_0603_1608Metric | D8 |
| 1 | MAX7456EUI_ | EasyEDA:TSSOP-28_L9.7-W4.4-P0.65-LS6.4-BL-EP-2 | U3 |
| 1 | MS561101BA03-50 | EasyEDA:SENSORS-SMD_MS5611-01BA03 | A1 |
| 1 | NANOT240AS | button:NANOT240AS | S1 |
| 1 | RX3 | TestPoint:1.5mm pad | TP11 |
| 1 | SA | TestPoint:1.5mm pad | TP18 |
| 1 | SMBJ28A | Diode_SMD:D_SMA | D1 |
| 1 | STM32F405RGTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TX3 | TestPoint:1.5mm pad | TP12 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | VID | TestPoint:1.5mm pad | TP19 |
| 1 | W25Q128JVPIQ | EasyEDA:WSON-8_L6.0-W5.0-P1.27-BL-EP | U5 |
| 1 | jst sh | Connector_JST:JST_SH_SM08B-SRSS-TB_1x08-1MP_P1.00mm_Horizontal | J2 |
Similar boards
- 4 layers115.5 × 90 mm

- 6 layers29 × 33 mm

MINIREX G4
mathieupommery/MINIREX_G473
The following table demonstrates the estimated component costs based on Mouser volume pricing. The unit price of each component dynamically adapts to the total quantity required for the entire production batch (1, 100…
109 parts10 - 4 layers38.4 × 82.8 mm

- 4 layers44.5 × 44.5 mm

QUT Autopilot Pixracer
Heckus/QUT-OpenFCU
The primary objective is to create an alternative to the difficult-to-source off-the-shelf Pixhawk 6. This work builds upon a edited pixracer version produced by KAI (Wesley) in 2022.
145 parts - 4 layers50 × 50 mm

MCU Board 0.1
thejamesrhodes/Hyades-Flight-Computer
Full Hardware and Electronics design, Bare-metal GNC flight software for an actively attitude-controlled high-power rocket
80 parts1Apache-2.0 - 4 layers50 × 50 mm

FlightController Drone
damnitzhemanth-oss/Flight_Controller
Custom STM based flightcontroller designed from scratch.
157 parts - 2 layers39 × 39 mm

- 4 layers150 × 137.1 mm

Controller
CircuitGuy943/Sabre-Integrated-flight-controller
(🚧) A "Jack of all trades" custom flight controller board. With support for both power and control and the ability for custom firmware
282 parts2GPL-3.0
Questions
How big is the 20x20 fc PCB?
It measures 40 × 40 mm and has 6 copper layers, 1.6 mm thick.
What parts does the 20x20 fc use?
120 parts, built around the MP4420GJ-P, MAX7456EUI, W25Q128JVPIQ and MS561101BA03-50. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the 20x20 fc KiCad files?
From the lmiez/yecnodF405 repository on GitHub, at the commit this page was made from: the board is KiCAD/20x20 fc.kicad_pcb and its schematic KiCAD/20x20 fc.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the 20x20 fc design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).