

DroneFluxx
ARM-based custom flight controller firmware + hardware.
- Size
- 45 × 45 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 78
- Pads
- 218
- Tracks, vias
- 398, 104
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Jan 2020
- Updated
- 27 Jul 2021
Overview
DroneFluxx is an open-source printed circuit board by kyleRhess, from the kyleRhess/DroneFluxx repository on GitHub. It is a 4-layer board of 45 × 45 mm with 58 parts on 78 nets, routed with 398 tracks and 104 vias.
It is built around the CAM-M8C-0, BMP388 and LIS3MDL, with the LP2985-33DBV and LSM6DSM among its other parts. Its parts include 16 capacitors, 6 resistors, 6 ICs, 5 connectors and 4 diodes. It belongs with the STM32 boards of this library.
Main components
5CAM-M8C-0
SMD-31P-167dBm -40℃~+85℃ 1.6V~3.6V GPS、QZSS、BeiDou、GLONASS UART、SPI SMD-31P GNSS Modules ROHSu-bloxGNSS ModulesBMP388
LGA-10(2x2)-40℃~+85℃ 1.65V~3.6V 1pa/K 2uA 30Kpa~1.25bar 50pa 8pa I2C、SPI LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsLIS3MDL
LGA-12(2x2)-40℃~+85℃ 1.9V~3.6V 16bit 1uA、40uA、270uA I2C、SPI ±1.6mT、±1.2mT、±8Gs、±4Gs ±1.6mT、±1.2mT、±8Gs、±4Gs LGA-12(2x2) 3D Magnetic Sensors ROHSSTMicroelectronics3D Magnetic SensorsLP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLSM6DSM
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 4KB Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometers
README
README.mdDroneFluxx
A custom quadcopter flight controller
Firmware
The current firmware version is tailored for an STM32F4 microcontroller. This means that it is best-suited for the related hardware, and much of this firmware is very proprietary.
However, the lightweight PID module built for this project could be useful in other applications.
Hardware
Flight controller hardware is still in work, but has been made public for those who are interested.

Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | Conn_01x01_Female | Measurement_Points:Measurement_Point_Square-SMD-Pad_Big | CH1, CH2, CH3, CH4, E1, E2, E3, E4, Gnd, Gnd, Gnd, Gnd, Gnd |
| 9 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C7, C8, C10, C11, C12, C13, C15 |
| 4 | 470 | Resistor_SMD:R_0805_2012Metric | R2, R3, R4, R5 |
| 4 | LED | LED_SMD:LED_1206_3216Metric | D1, D2, D3, D4 |
| 3 | Conn_01x01_Female | TestPoint:TestPoint_Pad_3.0x3.0mm | J20, J21, J22 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R6 |
| 2 | 10nF | Capacitor_SMD:C_0805_2012Metric | C5, C6 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C2, C9 |
| 2 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C3, C16 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C14 |
| 1 | BMP388 | kyleRhess_packages:LGA-10_2x2mm_Pitch0.5mm | U1 |
| 1 | CAM-M8C-0 | kyleRhess_packages:31-SMD_Module | U5 |
| 1 | Conn_01x02_Female | Connector_PinSocket_2.00mm:PinSocket_1x02_P2.00mm_Vertical | J2 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | LIS3MDL | Package_LGA:LGA-12_2x2mm_P0.5mm | U4 |
| 1 | LOGO | kyleRhess_logos:logo_blackmesa | G*** |
| 1 | LOGO | kyleRhess_logos:logo_foxhound | G*** |
| 1 | LOGO | kyleRhess_logos:logo_foxflight | G*** |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | LSM6DSM | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U2 |
| 1 | STM32F410RBTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U6 |
| 1 | SW_Push | Buttons_Switches_SMD:SW_SPST_KMR2 | RST |
The 54 most common of 58 parts.
Similar boards
- 2 layers44.5 × 50.8 mm

- 4 layers42 × 42 mm

Exa tim
hasenbanck/exa_tim
EXA_tim is a wrist watch PCB with GNSS time synchronization and e-paper display
53 parts6 - 2 layers53 × 85 mm

Flight computer
Rain-604/PERRII---Aerospace-Flight-Computer-version-2
PERRII - a modular aerospace flight computer designed for environmental sensing and long-range data telemetry
30 parts1 - 2 layers

Barry FL
Rain-604/PERRII---Aerospace-Flight-Computer
PERRII - a modular aerospace flight computer designed for environmental sensing and long-range data telemetry
41 parts - 4 layers45 × 98 mm

Ofc v3
rland93/ollyfc
A small rust-embedded flight computer. RTIC, FrSky protocols, and STM32F4 hardware.
151 parts3MPL-2.0 - 4 layers35 × 30.4 mm

Siplab wristband
bastocon/sparse-pose-benchmark
Bachelor Thesis Paper: Sparse Pose Estimation data collection, evaluation backend, frontend, as well as all resources for the creation of the Hidden Dataset using commodity sensors.
67 partsMIT - 4 layers53 × 35.2 mm

- 4 layers55.3 × 70.2 mm

FCC KiCAD
nikphillydev/NP1_DRONE
Building a quadcopter from scratch. Hardware and software. Developed using STM32 microcontroller and FreeRTOS.
116 parts3MIT
Questions
How big is the DroneFluxx PCB?
It measures 45 × 45 mm and has 4 copper layers, 1.6 mm thick.
What parts does the DroneFluxx use?
58 parts, built around the CAM-M8C-0, BMP388, LIS3MDL and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DroneFluxx KiCad files?
From the kyleRhess/DroneFluxx repository on GitHub, at the commit this page was made from: the board is Hardware/DroneFluxx.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DroneFluxx design in my own project?
Its repository states no licence, so its author keeps all rights: ask kyleRhess before reusing the design.