

Sugarkey
A small USB-C FIDO security key powered by RP2350 and Pico Keys.
- Size
- 20.4 × 29.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 39
- Nets
- 59
- Pads
- 180
- Tracks, vias
- 288, 29
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 24 Oct 2025
- Updated
- 25 Oct 2025
Overview
Sugarkey is an open-source printed circuit board by kristoferkp, from the kristoferkp/sugarkey repository on GitHub. It is a 2-layer board of 20.4 × 29.4 mm with 39 parts on 59 nets, routed with 288 tracks and 29 vias.
It is built around the AMS1117-3.3, ABM8-272-T3 and AOTA-B201610S3R3-101-T, with the WS2812B among its other parts. Its parts include 19 capacitors, 8 resistors, 2 ICs, 2 switches and 1 diode. It belongs with the RP2350 boards of this library.
Main components
4AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystalsAOTA-B201610S3R3-101-T
0806115mΩ 2.1A 2.4A 3.3uH Molded inductor 0806 Molding Power Inductors ROHSAbraconPower InductorsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdsugarkey
A FIDO2 compliant security key powered by my sugar addiction (and RP2354). Firmware is Pico Keys by Pol Henarejos.
Done in collaboration with Blueprint by Hack Club.
Features
- Powered by RP2354 with 2 MB of on-chip flash and built in security features.
- Open Source
- Compact (around 3cm x 2cm)
- Protective case
Getting started
- Have your sugarkey with you (JLCPCB fabrication files are in the production folder)
- Plug in your sugarkey while holding down BOOTSEL button.
- Download the latest Pico Keys firmware for the Raspberry Pi Pico 2.
- Copy the downloaded .uf2 file to the Picoboot storage mount.
- Commisson your sugarkey here.
- The LED is a WS2812 on GPIO 16.
- Plug the key into your device, it will show up as a passkey.
Hardware
- MCU: RP2354A
- LED: WS2812 or similar
- Raspberry Pi recommended LDO, inductor, crystal oscillator.
Disclaimer!
This isn't a finished product and shouldn't be trusted with super important stuff. I am in no way responsible for lost data.
Schematic

PCB

Picture of the JLCPCB cart

Parts
39| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | PCM_JLCPCB:C_0402 | C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C14 |
| 4 | 4.7uF | PCM_JLCPCB:C_0402 | C13, C15, C16, C17 |
| 4 | LOGO | LOGO | G***, G***, G***, G*** |
| 3 | 1kΩ | PCM_JLCPCB:R_0402 | R6, R7, R8 |
| 2 | 10uF | PCM_JLCPCB:C_0402 | C1, C2 |
| 2 | 15pF | PCM_JLCPCB:C_0402 | C18, C19 |
| 2 | 27Ω | PCM_JLCPCB:R_0402 | R3, R4 |
| 2 | 5.1kΩ | PCM_JLCPCB:R_0402 | R1, R2 |
| 2 | SW_Push | PCM_JLCPCB:SW_TS-1088-AR02016 | SW1, SW2 |
| 1 | 33Ω | PCM_JLCPCB:R_0402 | R5 |
| 1 | ABM8-272-T3 | PCM_JLCPCB:CRYSTAL-SMD_4P-L3.2-W2.5-BL | X1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | AOTA-B201610S3R3-101-T | SamacSys_Parts:AOTAB201610S3R3101T | L1 |
| 1 | RP2354A-QFN60 | RP2350_KiCad-main:RP2350A_QFN-60_EP_7.75x7.75_Pitch0.4mm | U1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | WS2812B | PCM_JLCPCB:LED-SMD_4P-L1.6-W1.5_XL-1615RGBC-WS2812B | D1 |
Similar boards
- 2 layers99.6 × 49.8 mm

- 2 layers70 × 99 mm

Campfire console
MeghanaM4/campfire-console
PCB Badges with TFT display, NFC module, lipo battery charging, and 6 programmable buttons
71 parts1MIT - 4 layers44.3 × 95.9 mm

- 4 layers72.5 × 39.7 mm

FOC RP2350
totaldesaster/SimpleFOC-Serial-Driver
Advanced dual BLDC driver based on the RP2350 and DRV8323S ICs, designed to be controlled from a trajectory controller over RS-485, RS-422 or TTL UART. Features a compact high power design with two stacked PCBs.
68 parts1GPL-3.0 - 4 layers68.6 × 56 mm

Cartridge
coco-chameleon/chameleon-hardware
TRS-80 Color Computer cartridge emulator
95 partsCERN-OHL-W-2.0 - 4 layers34 × 87.3 mm

- 4 layers68 × 75 mm

- 4 layers91 × 91 mm

Questions
How big is the Sugarkey PCB?
It measures 20.4 × 29.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Sugarkey use?
39 parts, built around the AMS1117-3.3, ABM8-272-T3, AOTA-B201610S3R3-101-T and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sugarkey KiCad files?
From the kristoferkp/sugarkey repository on GitHub, at the commit this page was made from: the board is PCB/sugarkey.kicad_pcb and its schematic PCB/sugarkey.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sugarkey design in my own project?
Its repository states no licence, so its author keeps all rights: ask kristoferkp before reusing the design.