
Pyaa
konomu/pyaa
A thirty key steno keyboard that runs with QMK firmware and direct pin connections. It only requires kailh choc switches, two pro micros, and two TRRS jacks.

A thirty key steno keyboard that runs with QMK firmware and direct pin connections. It only requires kailh choc switches, two pro micros, and two TRRS jacks.
Pyaa is an open-source printed circuit board by konomu, from the konomu/pyaa repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 123 × 154.9 mm with 18 parts on 23 nets, routed with 248 tracks and 0 vias.
Its parts include 16 switches, 1 IC and 1 connector. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.
A thirty key steno keyboard powered by QMK firmware and Plover.
To build pyaa, all you need is the following:
Once you have finished building it, you must flash the firmware onto the keyboard with QMK.
pyaa is powered by QMK firmware and takes advantage of its stenography, combo, and direct pin implementations. Its firmware is available here. It functions along with Plover, a desktop application developed as a part of the Open Steno Project.
There are many other steno keyboards out there, all of which allow you to input text at speeds upwards of 200 words per minute with the magic of Plover! (and of course, a bit of practice) In fact, pyaa is heavily inspired by Georgi, which was developed by g Heavy Industries' Jane Bernhardt and is available at gboards. Other options for steno keyboards can be found on Plover's wiki.
The PCB uses a direct pin matrix, where each key is connected to an I/O pin on the microcontroller and ground. This makes it so that soldering diodes onto the pcb is not necessary as with other keyboards, reducing cost slightly. N-key rollover functionality, which is crucial for stenography, is left intact.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | KEYSW | switches:Choc_PG1350_Choc_Spacing_Reversible | K0, K1, KA1, KHL1, KKL1, KN1, KO1, KPL1, KRL1, KS1, KS2, KST1, KST2, KTL1, KWL1 |
| 1 | MJ-4PP-9 | Lily58_Footprints:MJ-4PP-9_rev2 | J1 |
| 1 | ProMicro | Keebio-Parts:ArduinoProMicro | U1 |
| 1 | SW_PUSH | Lily58-footprint:TACT_SWITCH_TVBP06 | SW1 |

konomu/pyaa
A thirty key steno keyboard that runs with QMK firmware and direct pin connections. It only requires kailh choc switches, two pro micros, and two TRRS jacks.


VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.


Twotoz/C5VRX
Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS
It measures 123 × 154.9 mm and has 2 copper layers, 1.6 mm thick.
18 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the konomu/pyaa repository on GitHub, at the commit this page was made from: the board is reversible-old/pyaa.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).