
ProgrammaGull Sandpiper
4n3m4i1/PG_Logic
Open Source FPGA Development Boards for Education and Deeply Embedded Applications

Reforge 1 is an open-source printed circuit board by kishoriju-vrind, from the kishoriju-vrind/Reforge repository on GitHub. It is a 2-layer board of 61 × 77.8 mm with 96 parts on 124 nets, routed with 1,530 tracks and 181 vias.
It is built around the ICE40UP5K-SG48ITR50, ESP32-WROOM-32D and W25Q32JVSSIQ, with the AMS1117-3.3, SS8050 and 1N4148WT among its other parts. Its parts include 27 capacitors, 27 resistors, 9 connectors, 7 ICs and 5 diodes. It belongs with the ESP32 and FPGA and CPLD boards of this library.
THIS FOLDER IS MEANT TO STORE THE PCB DESIGNS, MADE ON KICAD 10.0
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C12, C14, C17, C18, C21, C24, C25, C27, C28 |
| 9 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C6, C7, C13, C15, C16, C19, C20, C22, C23 |
| 5 | 0.1uF/50V(10%) | Capacitor_SMD:C_0805_2012Metric | C2, C3, C9, C10, C11 |
| 5 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R16, R17, R18, R19 |
| 5 | Conn_01x12_Pin | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J8, J11, J12, J14, J15 |
| 5 | LOGO | LOGO | G***, G***, G***, G***, G*** |
| 4 | OPEN | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | SJ19, SJ26, SJ28, SJ29 |
| 3 | 10K(5%) | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R6, R26 |
| 3 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R7, R8 |
| 3 | DNI | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14, R20, R22 |
| 3 | RED LED | LED_SMD:LED_0603_1608Metric | PWR_LED1, PWR_LED2, PWR_LED3 |
| 3 | SHORT | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | SJ20, SJ31, SJ34 |
| 2 | 0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R23 |
| 2 | 10k(5%) | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R10 |
| 2 | 22.1K(5%) | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R5 |
| 2 | 5.1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R24, R25 |
| 2 | Conn_01x14_Pin | Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_Vertical | J9, J10 |
| 2 | SHORT | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | R13, SJ27 |
| 2 | SS8050 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 1N4148WT | Diode_SMD:D_SOD-523 | D1 |
| 1 | 2.2K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C26 |
| 1 | 22uF/10V(20%) | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 4.7uF/6.3V(10%) | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 47.5K(5%) | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | AP2112K-1.2 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | CP2102N-Axx-xQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U2 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32D | U5 |
| 1 | ICE40UP5K-SG48ITR | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U3 |
| 1 | LED_ABGR | LED_SMD:LED_RGB_Wuerth-PLCC4_3.2x2.8mm_150141M173100 | D2 |
| 1 | LED_Filled | LED_SMD:LED_0603_1608Metric | D7 |
| 1 | MountingHole | MountingHole:MountingHole_2.1mm | H1 |
| 1 | SG-210STF | Oscillator:Oscillator_SMD_SeikoEpson_SG210-4Pin_2.5x2.0mm | Y1 |
| 1 | SN74LVC2G125DCUR | SN74:SOP50P310X90-8N | U11 |
| 1 | SP0503BAHT | Package_TO_SOT_SMD:SOT-143 | D3 |
| 1 | SS14 | Diode_SMD:D_SMB | D6 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U8 |

4n3m4i1/PG_Logic
Open Source FPGA Development Boards for Education and Deeply Embedded Applications

Aztro-dev/MCL-Accel
Monte-Carlo Localization Accelerator board for the Vex V5 system

uzzambutt/NorthernStudios-iCE40-UltraPlus-FPGA-Dev-Board
NorthernStudios iCE40 UltraPlus FPGA Dev Board

sneakylizard123-4/FPGA_Board
It is built around the Lattice iCE40 FPGA, designed to be programmed over USB through the on-board FT232H. The SPI flash boots the bitstream on power-up.


4rynv/Eklavya_Gantry
an attempt to automate screwing out and in of screw holes arranged in a matrix formation

LeoSole423/PCB_SALUS_V3
PCB de control para el robot Ackermann SALUS. Esta revision se inspira en la arquitectura de Hoja-Base, pero usa un ESP32-S3 y se mantiene como un diseno independiente.

mubarizahmed/desk_control
Firmware for an ESP32 based physical productivity widget
It measures 61 × 77.8 mm and has 2 copper layers, 1.6 mm thick.
96 parts, built around the ICE40UP5K-SG48ITR50, ESP32-WROOM-32D, W25Q32JVSSIQ and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the kishoriju-vrind/Reforge repository on GitHub, at the commit this page was made from: the board is KICAD/Reforge_1.kicad_pcb and its schematic KICAD/Reforge_1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask kishoriju-vrind before reusing the design.