Skip to the content
2 layers22.2 × 32 mmCmos guy2, the printed circuit board in 3D

Super simple square wave oscillator with speaker and stereo line out

Size
22.2 × 32 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
7
Pads
31
Tracks, vias
93, 9
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
26 Apr 2019
Updated
16 May 2020

Overview

Cmos guy2 is an open-source printed circuit board by kinoshita-lab, from the kinoshita-lab/cmos_guy2 repository on GitHub, published under the MIT licence. It is a 2-layer board of 22.2 × 32 mm with 10 parts on 7 nets, routed with 93 tracks and 9 vias.

It is built around the TC7W14FU and CR2032. Its parts include 3 capacitors, 1 resistor, 1 IC, 1 diode and 1 connector.

Main components

2

README

README.md

CMOS野郎2

説明

CMOS野郎2は、シュミットトリガインバータ(TC7W14FU)を使った発振器と、スピーカーを組み合わせた、電池で動くシンプルな楽器です。 ステレオラインアウトもあります。

初代CMOS野郎(初代CMOS野郎 https://github.com/kinoshita-lab/cmos-guy )を基板化&小型化したものです。

基本的な使い方

  • 電池を入れると動きます。向きに気をつけてください。 使わない時は電池をはずしてください。
  • あまり奥まで電池を入れると、抜くのが大変なので途中くらいにしておくとよいです。
  • ツマミを回すと、ピッチが変わります。

応用的な使い方

  • 回路がむき出しになっているので、あちこち触ってみると面白いです。
    • ツマミの裏辺りを触ると微妙にピッチが変わります。上手くやるとビブラートもできます。
    • スピーカーの穴を指でふさいだりすると、微妙にフィルターがかかります。
  • 複数使うと、うなり(beat)が作れて面白いかもしれません。
  • ミキサーに差すと、とりあえずPAつながってる?とかわかって便利かもしれません。

交換が必要な部品

電池は CR2032 を使って下さい。

回路

Parts

10
QtyValueFootprintReferences
20.1uCapacitors_SMD:C_0603_HandSolderingC2, C3
1100uCapacitors_SMD:C_1206_HandSolderingC1
110kmylib:POT_TOCOS_GF063P1RV1
1AudioJack3mylib:stereo_3.5mm_stereo_uxcell_thruholeJ1
1CR2032mylib:Battery_Holder_CR2032_AkidukiBT1
1LEDLEDs:LED_0603_HandSolderingD1
1RResistors_SMD:R_0603_HandSolderingR1
1Speakermylib:UGCM0603APE_Akiduki_Small_Speaker_6.7mmLS1
1TC7W14FUHousings_SSOP:SSOP-8_2.95x2.8mm_Pitch0.65mmU1

Similar boards

  • 2 layers333.4 × 149.9 mmOmega Mainboard, the printed circuit board in 3D

    Omega Mainboard

    skiselev/omega

    Omega Home Computer

    248 parts459GPL-3.0
  • 2 layers17.2 × 30.4 mmWeigand, the printed circuit board in 3D

    Weigand

    linklayer/BLEKey

    A Bluetooth Low Energy device for interfacing with Wiegand

    17 parts268
  • 4 layers188 × 188 mmITX Llama, the printed circuit board in 3D

    ITX Llama

    eivindbohler/itxllama

    422 parts246GPL-3.0
  • 2 layers61 × 36.8 mmKeebcard, the printed circuit board in 3D

    Keebcard

    rsheldiii/Keebcard

    Home of the KeebCard project - Kicad files, code, and more!

    15 parts112
  • 2 layers59.2 × 41 mmBluey, the printed circuit board in 3D

    Bluey

    electronut/ElectronutLabs-bluey

    Nordic nRF52832 BLE development board with sensors.

    79 parts96
  • 2 layers35 × 35 mmQron0b, the printed circuit board in 3D

    Qron0b

    qewer33/qron0b

    a sleek and low-power binary wristwatch

    35 parts62GPL-3.0
  • 2 layers90 × 89.4 mm38-04-usb sleuth, the printed circuit board in 3D

    38-04-usb sleuth

    smaroukis/usb-sleuth

    USB cable continuity tester ++

    68 parts61
  • 2 layers170.2 × 100 mmZ80-SBC, the printed circuit board in 3D

    Z80-SBC

    skiselev/zeta_sbc

    Zeta SBC is an Zilog Z80 based single board computer. It is inspired by Ampro Little Board Z80 and N8VEM project. Zeta SBC is software compatible with RomWBW Firmware

    75 parts53GPL-3.0

Questions

How big is the Cmos guy2 PCB?

It measures 22.2 × 32 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cmos guy2 use?

10 parts, built around the TC7W14FU and CR2032. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cmos guy2 KiCad files?

From the kinoshita-lab/cmos_guy2 repository on GitHub, at the commit this page was made from: the board is cmos_guy2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cmos guy2 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).